We offer high quality hydraulic compression testing machines, which are designed for carrying out compressive strength tests on cement cubes, concrete and other such different materials. These machines are available in the capacity of 25KN to 3000KN and are supplied with pressure gauge and digital display. It can test the cubes specimens of sizes 10cm to 20cm and cylinder specimens of sizes 7.5 x 15cm to 15 x 30cm. The frames of this hydraulic compression testing machines are steel fabricated and are constructed in the following way:

Channel type with hand or electric cum hand operated pumping unit.

Two pillar type with hand or electric cum hand operated pumping unit.

Two pillar nut type with hand or electric cum hand operated pumping unit.

Four pillar welded type with hand or electric cum hand operated pumping unit.

We manufacture and supply AIV apparatus, which are conforming to IS 2386. These machines are used for determining the aggregate impact value. The sturdy construction of our AIV apparatus consists of base and support columns to form a rigid framework around the quick release trigger mechanism to ensure an effective free fall of the hammer during test. The free fall are adjustable. The hammer is
provided with a locking arrangement. The apparatus is supplied complete with cylindrical cup, metal measure and tamping rod. Our range of AIV apparatus has been designed in a particularly heavy-duty form, with specially hardened steel surfaces for minimum wear.

Our specially designed electric vibrating machine is designed to suit compaction of 7.06cm mortar specimen according to IS 4031 requirements. It is used for vibrating the mix in moulds according to strictly controlled program at a frequency of 12,000 rotation per minute. These vibrators are mounted over coiled springs and the vibrations are developed by means of a revolving eccentric shaft. The simple design of the machine facilitates easy assembly and dismantling of the cube moulds.

Our mixing and moulding equipment are manufactured as per the IS standards and also BS 1881:DIn 51229, Bs 1881:Part 110. We offer these moulds in various specifications and are available in materials like cast iron, steel cylinder and steel beam. Different specifications of cast iron moulds are:

It is available in cube mould with clamp, base pate and the size available is 150mm x 150mm side.

It is available in cube mould with clamp, base pate and the size available is 100mm x 100mm side.

It is available in 3-gang mould with clamp, base pate and in size 50mm x 50mm side.

It is available in cylinder mould and the size is 100mm diameter x 200mm (H)

It is available in cylinder mould and the size is 150mm diameter x 300mm (H)

It is available in cylinder mould and the size is 160mm diameter x 320mm (H)

Different specifications of steel cylinder moulds are:

It is available in cylinder mould and the size is 100mm diameter x 200mm (H)

It is available in cylinder mould and the size is 150mm diameter x 300mm (H)

It is available in cylinder mould and the size is 160mm diameter x 320mm (H)

Different specifications of steel beam moulds are:

It is available in beam mould with clamp, base pate and the size available is 150mm x 150mm x 750mm.

It is available in beam mould with clamp, base pate and the size available is 100mm x 100mm x 500mm.

It is available in tamping bar of 25mm square mortar cube mould 7.06cm side.

Humidity oven are designed specially for climatic and durability tests. These are used for drying environment of plant, animal growth, investigation of vapour proofing of packed material, determination of die-electric strength, insulation test of electronic component, mechanical assemblies, paints, etc. The exterior of humidity ovens is made of heavy gauge ms with durable powder coating paint in pleasant shade and interior made of polished stainless steel or anodised aluminium. This ovens are having superior thermo fibre board or puf insulation. It gives a full view inner glass door with
metal frame to inspect the specimen from outside without disturbing the specimen or loosing the temperature of the chamber is also provided, outer door is of massive construction having seals against atmospheric infiltrations by rubber gasket. Air circulation arrangement is done with the help of suction blower with turbo fhp motor.

Motorised 50 Kn Cbr Marshal Test Machine Bench Mounted
We manufacture and supply Motorised 50 Kn Cbr Marshal Test Machine Bench Mounted, with geared speed drive control and simple selector switch for 3 speed, 1.0mm/min (BS), 1.27mm/min (ASTM) and 50.8mm/min (Marshall). It is provided with platen adjustment switch for forward and reverse on CBR test. Power required for the operation is 240V, 50 Hz, 1pH. Some of the features of our Motorised 50 Kn Cbr Marshal Test Machine Bench Mounted are:

Penetration plunger.

Dial gauge holder with stopper.

Dial gauge 20mm x 0.01 mm per division with certificate.

Stability mould, open type, made from steel with inside diameter of 4'' to dimension given in BS598.

Flow meter (dial gauge) with 10mm travel x 0.01 mm resolution and stopper unit.

Our direct and residual shear apparatus comes with shear box apparatus premises, which can test the both square and circular specimens of 60mm, 70mm, 100mm, .5'' diameter. The speed rate is controlled by gears system that can keep consistent under load stress. Our direct and residual shear apparatus is provided with rapid adjustments and safety limit switch, which prevent from over strain and overloading of the apparatus. It is supplied with shear box assembly, load ring, vertical and horizontal dial gauge and weight set.

Our core drilling machine combines innovative features, precision engineering and compact design for professional drilling operations such as taking out specimens from floor, reads and runways. It answers the demands of the coring industry and created this unit to master every drilling environment and challenge. Our drilling machines are built to stand up to all the dynamic rigors of the professional market. It is the combination of advanced technology, simplicity of
design and high quality components to deliver exceptional drilling performance.
Features of our core drilling machine include Anchor/vacuum base, mast, carriage, control panel, vacuum pump, ceiling jack and motor mount plate. It comes with the electrically operated and machine with petrol engine are available that make it the premier choice in core drilling machines.

Our tensile testing machines are electrically operated and are used for determining the tensile strength and elongation of various materials like rubber, plastic, paper, wires, chords etc. These machines are manufactured in various capacities and test appropriate traverse speed and using suitable grips in conformity with ASTM, DIN, BIS, and BSS standards. It is fitted with over-travel safety switches suitable for 230 V AC supply. This machine is available in analogue as well as digital models and with the capacity of 100kg to 5 ton.

Our range of motorised test sieve shaker carries 8 sieves of 20 cm diameter and 6 sieves of 30cm diameter. The sieve shaker is driven by 1/4 HP motor through reduction gearbox. It is suitable for operation on 240V, 50 HZ 1 pH and weigh 80kg. We also provide laboratory and rotate type shakers.

Our Los Angeles Abrasion Testing Machine is used for determining the resistance of small size coarse aggregates and crushed rock. It consists of a hollow cylinder, mounted on a sturdy frame on ball bearings and with a detachable shelf which extends throughout the inside length of the drum catches the abrasive charge and does not allow it to fall on the cover. The drum of this machine is rotated at a sped of 30-33 rpm by an electric motor through a heavy-duty reduction gear. It is supplied completely with a tray for collection of the materials with revolution counter and abrasive charge.

Our high performance vibratory hammers are not only used for driving and extracting piles and steel profiles but also for soil compaction. It generate vertical oscillating movements with an average frequency of 1200 to 3000 (20 to 50 Hz) depending on the hammer used. The vibrations produced by the hammer reduces or remove the inner soil stresses so only small forces on the pile are needed to penetrate the soil. The weight of our hammer itself is normally enough to provide for the penetration.