Models F21-E1B (shown in picture) are designed for 3-motion (namely Main Hoist, Cross travel & Long travel).
Model F21-E1B is with single step push button type transmitter which can be used to achieve single speed for each motion similar to pendant operation.

Specifications:
 
 Transmitter

• 6 single-step buttons ,1Emergency stop,1 start button
• Powered by Size: AAx 2 (Alkaline battery) 
• providing 9 control contact.
• Size: 164 x75 x 46 mm (excluding protrusion)

 
Receiver

•        Power Supply: 110/220VAC50HZ
•        Relay output: 10A/250V
•        Size: 185x85x85 mm
•        Antenna
•        Weight: About 550 g

Model F24- BB ( Shown in the picture )

Our design for 4-motion ( Namely main hoist, Aus hoist, Cross travle & Long travle. This modle is with single step bush button type transmitters which can be used to achieve single speed of each motion similar to pendant operation.

Specifications:

General

• Encoding : Microprocessor based
• Decoding : Microprocessor based
• Range     :    100M Approx.
• Temperature : -30 degree C - +80 degree C-


Transmitter

• 10 single-step buttons, 1 Emergency stop, 1 start button
• Powered by size AA X 2 Alkaline battery.
• size : 186 X 61 X 51 mm ( excluding protrusion )
• Power supply : 3V
• Weight : about 260gms
• Housing : Nylon fiber

Receiver

• Power Supply   : 110/220VAC 50 Hz
• Size                : 200X 162 X 51 mm
• Housing           : Nylon Fiber
• Weight             : About 1225 gms

Model F24-10D (shown in picture) is with 2 step push button and can offer 2 speeds ( i.e. slow speed on the first step of the push button and 2^nd step of the push button can be used to achieve full speed).

Specifications:

General

• Encoding - Microprocessor based
• Decoding - Microprocessor based
• Range - 100M Approx.
• Temperature – - 30 degree C - +75 degree C


Transmitter

• 10 double-step buttons, 1 Emergency stop, 1 Rotary key switch, 1 Start button
• Powered by size AAx 2 Alkaline battery.
• Size : 186 x 61 x 51 mm (excluding protrusion)
• Power Supply - 3VDC
• Weight - About 260gms
• Housing - Nylon fiber


Receiver

• Power supply - 110/220 VAC 50Hz
• Size - 200 x 162x51 mm
• Housing - Nylon Fiber
• Weight - About 1225 gms

Shoulder held transmitter with joysticks for crane shall be replica of the crane controls provided by you for the cabin. The joystick will have speed steps in each direction. The other functions shall be carried out through push buttons/switches provided on the transmitter. The joystick systems have been provided with dual joysticks with proportional control if required.
 
The dual joystick is much easier for the operator to use compared to single joystick. In dual joystick, hoisting and lowering is carried out in vertical plane whereas cross travel and long travel in horizontal plane unlike single joystick system where all the joysticks have to be moved in vertical plane, despite the fact that cross travel and long travel motions are required to move in horizontal plane. With the use of dual joystick the transmitter becomes light and compact. Proportional control is also not possible in single joystick system.
 
Specifications:

General
• Encoding - Microprocessor based
• Decoding - Microprocessor based
• Range - 100M Approx.
• Temperature – 35 degree C - +80 degree C

Transmitter

• 2 dual joysticks with 5 speed steps. Any two motions can be clubbed in one joystics • Control of additional motions with push buttons and rotary switches.
• Powered by size AA x 4 Alkaline or rechargeable battery.
• Size : 220 x 110 x 90 mm (excluding protrusion)
• Power supply : 6V
• Weight : Approx 860 g
• Housing : Nylon- Fibre

Receiver

• Power Supply : 110/220VAC50HZ
• Size : 290 x 230 x 70 mm
• Housing : Nylon-Fiber
• Relay Output : 10A/250V
• Antenna : External
• Weight : Approx. 2200 g