A. Damiano & Company

pole bands supplied complete with four studs or bolts and square nuts
all ferrous parts are hot dip galvanized to astm a153 / bs 729

Anchor rods supplied with one square nut unless otherwise specified
Washer can be supplied at additional cost.
Recommended size of washer is as stated above.
All ferrous parts hot dip galvanized to ASTM A153
Thimble eye anchor rods conform to requirements of ANSI C135.2

Anchor Shackles supplied complete with one cotter & pin

Shackles available in various strength ratings by using difference grades of steel

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729 except
cotter pin which is of stainless steel

Anchor Shackles supplied complete with one bolt & nut Shackles available in various strength ratings by using difference grades of steel
All ferrous parts are hot dip galvanized to ASTM A153 / BS 729 except cotter pin which is of stainless steel

Clamps are capable to withstand dielectric strength of 6000V for one minute
Anchoring clamp consists of body made of aluminium alloy or thermoplastic
Wedge is made of zinc alloy or thermoplastic
Bail is made of stainless steel or hot dip galvanized steel
All dimensions

Minimum failing load of anchoring eye is 30 KN

The anchoring eye is securely welded to the base which fits on to pole or wall surface

All ferrous parts are hot dip galvanized to BS 729

Ball Clevis available as forged or as cast

Ball clevis supplied complete with one cotter and cotter pin

Ball clevis can be supplied in higher strength rating if required
by using higher strength steel and heat treatment thereof

All ferrous parts hot dip galvanized to BS 729 except
Cotter pin which is made of stainless steel

Ball Clevis conforms to requirements of BS 3288

Ball eye available as forged or as cast

Ball eyes can be supplied in higher strength rating if required
by using higher strength steel and heat treatment thereof

All ferrous part are hot dip galvanized to BS 729

Ball eyes conform to requirements of BS 3288

Ball eye available as forged or as cast

Ball eyes can be supplied in higher strength rating if required
by using higher strength steel and heat treatment thereof

Ball eye supplied complete with one hex bolt, nut & spring washer

All ferrous parts are hot dip galvanized to BS 729

Ball eyes conform to requirements of BS 3288

All ferrous parts hot dip galvanized to BS 729

B&S Coupling confirms to 16mmB

Pig Tail Hooks can be supplied in higher strength rating if required
by using higher strength steel and heat treatment thereof and also
using special designs of eye to increase strength function

Pig Tail hooks conforms to requirements of BS 1320
Other sizes

Binding stirrups offer traditional method of securing conductor
on to groove of insulator with binding wire

Binding stirrups are made of high strength aluminium alloy wire

Binding Stirrups conform to requirement of BS 1320

Catalog A B C D E F R D1
BR-01 45 34 60 30 34 15 12 5

Catalog A B C D E F R
BR-02 52 30 10 12 8 6 20

Busbar Insulators are made of moulded DMC composite with
Integral inserts of extruded high strength brass in natural finish

The brass inserts can accept ISO Metric threaded fixing bolts
of the nominal diameters as stated above
Other

CATALOG A B C D
ICS - 01 64 79 64 10

P.F. withstand voltage :- 8 kv
Impulse withstand :- 20 kv

Failing loads
In line with screw :- 4.0 kn
Lateral pull :- 2.5 kn

Weight :- 0.35 kg approx

The insulators are made of porcelain or nylon composite

The screw is made of hot dip galvanized steel

Conical dead end clamps can be used for terminating the aerial bundles cables on a pole or wall when used with other wall / pole
fixing clamps
The grips is designed such that it can accept a range of conductor diameter and still provide effective grip under load conditions
The clamps , grips and nuts are made of high strength aluminium alloy and Bail is made of hot dip galvanized steel

Typical arrangement of complete cross arm assembly

1. Intermediate Crossarm
2. Earth Wire Cross arm
3. Flat Tie Strap
4. Angle Tie Strap
5. Pole Fixing Bolts & Nuts
6. Brace fixing bolts & Nuts
7. Pole ( not in our scope of supply )
All ferrous parts are hot dip galvanized to ASTM A153 / BS 729
Cross arms available in various shapes and sizes as per user requirement

The compact lightweight construction of the cutouts
ensures complete ease of installation. Each unit is
secured by a single bolt fixing at centre mounting
point. An adjustable support bracket complete with
bolts , nuts and washer is available on request and
suitable for cross arm pole of wall mounting.

4. The fuse carrier is designed to accommodate
standard expulsion Fuse Links of the button head
pattern. Two speeds of operation are available :- Type K
( Fast operating ) and Type T ( Slow operating ) each
with rating for 1 to amperes
Insulation level for a given system voltage can vary
considerably with climatic and environmental
conditions. The availability of both single and double
insulator style of cutouts can therefore provide and
optimum choice in the selection of most suitable design

CATALOG A B E F T
DWDB-01 44 52 10 24 5

Minimum Failing load of distribution bracket is 2 KN

All ferrous parts are hot dip galvanized to BS 443

Drop wire distribution clamps consists of clamp made of poly carbonate
Material and hook made of hot dip galvanized steel

Clamps are also available in various grade of nylon if required

Bails are also available in stainless steel if required

Double arming bolts supplied complete with four square nuts

Spring washer are recommended but supplied against additional costs only if specified

All ferrous parts are hot dip galvanized to ASTM A153

Double arming bolts and nuts confirm to requirements of ANSI C135.1

Drive hooks are single pierce forged construction with high strength
buttressed threads suitable for pole , wall or concrete fixing

The unique design provided seating surface to hammer or any power
tool to drive the hook into the wall or concrete with easy and safely

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729

Drive rings are supplied with one hardened steel pin suitable
for pole , wall or concrete fixing of the ring with ease

All ferrous parts are hot dip galvanized to BS 443

Drop wire dead ends are made of stainiess steel with

applied length coated with neoprene/polyviny/compounds

for use with insulated and jacketed conductors

Fixing nails supplied complete with 120 mm long bolt

Fixing nails consist of body and insert made of nylon composite and
Fixing bolt made of hot dip galvanized steel

The expanding inserts helps to firmly grout the bolt on the
pole or wall surface
Other

Guy grip dead ends are made of galvanized steel confirming to BS 443

heavy coating as per Class A-C of ASTM A-495 are also avaliable on request

Insulated Clevis supplied complete with one cotter and cotter pin

All ferrous parts are hot dip galvanized
except cotter pin which is made of stainless steel

Insulated piercing connector is used for connecting LV Insulated
overhead line to another LV Insulated Overhead line

Body is made of thermoplastic with tinned copper blades and bolts
made of hot dip galvanized steel

All ferrous parts are hot dip galvanized to ASTM A153

Long shank supplied with square nut, mf lock nut , square washer and spring washer
Short shank supplied with square nut and two spring washers

Eye nuts are single piece forged construction

Eye nuts are tapped oversize ( 0.015 ) as permitted after galvanizing to ensure smooth fitment with matching threads on bolts

All ferrous parts are hot dip galvanized to ASTM A153 and internal threads oiled after re tapping to prevent rusting as permitted by specification

HV Pins long shank supplied complete with one nut , one lock nut & one washer
( round / square )
HV Pins short shank supplied complete with one nut & one spring washers
HV Pins available in lead & nylon threads
All ferrous parts hot dip galvanized to ASTM A153

Shank Length 50 or 130 mm
to be specified while ordering

All ferrous parts hot dip
Galvanized to BS 720

Pins confirming to BS 3288

Line Pins supplied complete with one hex nut .
Additional lock nut and washers can be supplied at extra cost
Please add suffix l ( lock nut ) , p ( plain washer ) and s ( spring washer )

Pilot Pins ( Fig 1 ) supplied complete with two hex nuts

Additional lock nut and washers can be supplied at extra cost

Please add suffix l ( lock nut ) , p ( plain washer ) and s ( spring washer )

Transformer Lead Pins available in lead & nylon threads
All ferrous parts hot dip galvanized to ASTM A153
Other

Pin type brackets supplied complete with one self locking cotter

All ferrous part hot dip galvanized

Self locking cotter is painted with protective paint at locking portion
since it is locked after galvanizing is completed

Saddles can be supplied and to be ordered separately

Riser Guards are made of pressed steel of 2 mm thickness

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729

Service drop wire clamp consists of:-

- Shell made of stainless steel and serrated

- Wedge with attached tail made of stainless less

- Shim made of polyethylene or equal to induce smoother wedge action

Insulators conform to requirements of BS 137

Insulators available in brown or white glaze

Shoulder eye bolts eliminate need of additional washer under the eye

Shoulder eye bolts supplied complete with one nut ( hex / square )
Unless otherwise specified

Washers ( round / spring ) can be supplied at additional costs

All ferrous parts hot dip galvanized to BS 729

Shoulder eye bolts conforms to requirements of ESI 43-91 / ANSU C135.4

Other sizes & ratings available on request
All dimensions in mm * We reserve the right to change design & construction without prior notice

Socket clevis available as forged or as cast

Socket clevis supplied complete with one security clip , one cotter & pin

Security clip may be w or r type.
Please specify by adding w or r to the suffix while ordering

Socket clevis conforms to requirements of BS 3288

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729
excluding security clip and cotter pin which is made of stainless steel

Socket eye available as forged or as cast

Socket eye supplied complete with one security clip

Security clip may be w or r type.
Please specify by adding w or r to the suffix while ordering

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729
excluding security clip which is made of stainless steel

1. STRAP 197 X 45 X 8 HDG STEEL 4 NOS
2. CUP HEADED BOLT& NUT HDG STEEL 2 NOS
3. HEX BOLT & NUT M20 X 65 HDG STEEL 2 NOS
4. ARCING HORN & NUT HDG STEEL 2 NOS
5. STAY INSULATOR WOOD UW1 1 NOS
6. THIMBLE HDG STEEL 2 NOS

X = 57 MM
W = 25 MM
Stay Insulators are made of laminated densified wood duly treated For high voltage application

Stay Insulators conform to requirements of BS 137

Stay insulators available in brown glaze
Other

Stay straps supplied complete with one thimble assembled together
All ferrous parts are hot dip galvanized to BS 729

CATALOG A B C D
SC-0-30-DEG 309 132 55 18

Suspension Clamps are made of pressed steel and supplied
Complete with retaining bolts and nuts which are hot dip galvanized steel

Suspension Clamp assembly consists of suspension clamps with
rubber inserts , pig tail hook assembled with two nuts

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729
Other sizes

Clamps are made of hot dip galvanized cast iron
Bolts are made of hot dip galvanized steel
Minimum failing load of clamps is 3 KN

Suspension Clamps are supplied complete with two no M8 x 35 mm
Hex bolts and are hot dip galvanized to ASTM A153 / BS 729

CATALOG W L G
SC-30-60-DEG 100 MIN 90 MAX 24 MIN

Suspension Clamps and keeper are made of cast high strength
Aluminium alloy

Protector is made from poly ethylene composite

Suspension Clamps are also available with complete insulation
Other sizes

Braces available in straight / twisted types of varying sizes

All ferrous parts hot dip galvanized to ASTM A153 / BS 729

Catalog A B C D E
WB-CA-02 125 65 100 100 60

Wall brackets are made of high strength cast aluminium alloy

All ferrous parts are hot dip galvanized to ASTM A153 / BS 729