AGC Chemical

Liquid and auto-instrument wind drying of petrochemical, textile and oxygen-marking industries, psa in air-separation are the properties and uses used as dryer in gas phase. It is very suitable for the use of heat free regeneration device due to its high heat-adsorption quantity of single molecular absorbing layer.

Precautions:don't unpack the product before use, in order to avoid moisture adsorption and efficiency

Decrease of use: the product is suitable for deep drying with the pressure over 5kg/cm2.

The Actived Alumina should be regenerated to remove the absorptive moisture as the absorptivity ability will decrease gradually after a certain time in order to its repetitive use.

The gases use for the regeneration should be dried gas with lower or same operating pressure of drying operation. The dried gas should be used with higher the temperature of dying operation, while wet gas should be used after rising temperature.

We are engaged in manufacturing carbon molecular sieve, that is widely used in petroleum & chemical and heat treatment of metal, electronic manufacture and food preservation industries. It is a nonpolar absorbent with adsorbing oxygen molecule to get nitrogen-enriched air at normal temperature. Made using premium grade raw material, our range is known for features such as precise pH value, pure, and accurate composition.

The product is suitable for deep drying with the pressure over 5kg/cm2. The absorptivity ability generally tend to decrease gradually with the after certain time. Thus to use it repeatedly, the product should be regenerated to remove the absorptive moisture.

The dried gas should be used with lower or same operating pressure for regenerating the product. For drying operation, the dried gas should be used either higher or same temperature.

Our facilities empower us to pack 50kgs of the product in a 22 gallons steel drum 140kgs gallons steel drum.

Precautions: don't unpack the product before use in order to avoid moisture adsorption and efficiency decrease of use.

Molecular Sieve Type 13X is the sodium form of type X crystal. It has a much larger pore opening than the type A crystals. It will adsorb molecules with a kinetic diameter of less than 9 Angstrom (0.9nm) and will leave out which are larger than that. It has got the highest theoretical capacity of the common adsorbents. Further, it also proffers very good mass transfer rates. It is powerful enough to remove impurities as large as to fit into a type a crystal. Molecular Sieve Type 13X is commonly used to separate nitrogen from oxygen.

Applications :

• Paraffin sweeten Removing CO2 and H2O from air
• Solvent drying
• Treatment of acetic acid process gases
• Natural gas sweetening
• Drying and sweetening of rocket propellant
• NH3, synthesis gas drying and purifying
• Removing C02 from steam cracked gas
• Sweetening and drying of liquefied petroleum gas

We offer it in a best packed way in 25/136-150kg air-tight steel drum. Further, we also offer it in 500kgs super sack bag. Our in-house facilities empower us to store the chemical in 2 to 50c degree and max 90%RH in dry room. Our storage also prevent it against water, acid and skills.

We are an eminent manufacturing and exporter of Molecular Sieve Type 3A which is an alkali metal alumino-silicate. It is the potassium form of crystal structure. Type 3A has an effective pore opening of about 3 angstorms (0.3nm).It carries a large structure so that it can allow in moisture. Furthermore, it excludes molecules such as unsaturated hydrocarbons which can potentially form polymers. This capability allows to maximize the lifetime during dehydration of such molecules.

Applications :

• Olefin drying (ethylene, propylene. But adience)
• Drying of polar liquids(methanol, ethanol)
• Drying of cracking gas/liquid
• Drying of polymer plant feed
• Drying N2-H2 mixtures made by cracking of NH3 C02,
• Solvent drying of liquefied petroleum gas
• Deep drying of kerosene and jet fuel.

We offer our range of Molecular Sieve Type 3A packed in 25/136-150kg air-tight steel drum as well as 500kgs super sack bag. Our smartly equipped warehouse allow us to storage the product 2 to 50c degree along max 90%RH in a dry room which is required for the chemical. Further, our storage system Prevents them against water, acid and skills.

Molecular Sieve Type 4A is the sodium form of the type A crystal structure which is an alkali metal alumina silicate. 4A molecular sieve has an effective pore opening of about 4 angstroms (0.4nm) [Cant Re-phrase]. 4A molecular sieve will adsorb most molecules with a kinetic diameter of less than 4 angstroms excluding the larger ones. Our range of Molecular Sieve Type 4A can absorb molecules such as oxygen, nitrogen, carbon dioxide and straight chain hydrocarbons. On the other hand, the process excludes branched chain hydrocarbons and aromatics.

Applications :

• Deep frying of glass and liquids (air, natural gas, industrial gases, noble gases, alcohol)
• Removing of carbon dioxide, ammonia and methanol from liquid.
• Drying natural gas

Our packaging facilities allow us to pack the product in 25/136-150kg air-tight steel drums as well as 500kgs super sack bags. We store these 2 to 50c degree, max 90%RH in dry room. Our expertise allow to prevent our range of Molecular Sieve Type 4A against water, acid and skills.

Molecular Sieve Type 5A is an alkali alumina silicate. It is the calcium form of the type A crystal structure that come with an effective pore opening of 5 angstroms (0.5nm). Molecular Sieve Type 5A adsorbs molecules with a kinetic diameter of less than 5. The product is especially suitable for PSA absorber applications. It may be used for the separation of is - paraffin (C4 to C6 species), in PSA hydrogen and in oxygen concentrators.

Applications :

• Separating of normal and isomeric hydrocarbons
• Natural gas drying,
• Removing CO2 sweetening,
• N2/O2 Separating
• Separating of aromatics,
• H2 purification
• Liquefied petroleum gas sweetening

Our warehousing and packaging is equipped enough to packing it in 25/136-150kg air-tight steel drum. While we also pack it in 500kgs super sack bags too. We keep these in 2 to 50c degree temperature which is best for it. Along with max 90%RH in dry room we also make sure that our range is getting proper prevention against water, acid and skills.