A. K. Industries, Mumbai

AK Industries range of Ball Valves are designed for use in hazardous and corrosive environment. All Ball Valves are preciously machined, designer durability and maximum efficiency to provide high quality and low cost.

Features

• Two way on off, 3 or 4 way swiching models.
• Blow-Out Proof Bottom Loaded stem.
• Low operating torque with SS lever/Fenolic handle.
• Full or reduced Bore for Perfect Flow.
• Floting ball design for positive seating.
• Working Pressure from 1000 PSI to 6000 PSI.
• With PTFE seat.

Construction

SS-316, SS-304, Carbon Steel, Brass and Monel Material in different type of end connection include Male/Female thread NPT, BSP, BSPT and Single or Double Tube Fittings ends.

Application

Process Control, Instrumentation.

AK Industries offers a full range of Industrial Valve like Gate, Globe, Butterfly, Check and Ball Valves, Special Valves like Flush Bottom, Flush type Ball Valve, Three Way / Four Way and Jacketted Ball Valves are also manufactured.

AKI Industrial Valves are design and manufactured in compliance with API, ANSI and other standards.

Construction

Generally fabricated from Forged, Cast or Barstock in cast iron, cast steel, mild steel, stainless steel, alloy steel and higher grade alloys such as Hast alloy 'C' & 'B', Size range is from 1/4" to 18" sizes varying from 150 to 2500 Class.

Application

AK Industries has been manufacturing high quality valves, which have been used in Oil & Gas, Petro-chemical, Fertilizers, Mining,Power Plants & many other industries.

AK Industries manufacture complete range of manifolds specially designed for applications in process, chemical, petrochemical and offshore installation to control, measure, isolate, equalize, calibrate, drain, vent or differentiate the pressure of liquids and gases.

AK Industries valve manifolds series offer 2,3 and 5, valves configuration which come in remote mounting R type (Pipe to pipe)direct mounts T & ‘H’ Type (Pipe to Flange & Floating to Flange) on to the instrument on 54 mm center.

AKI Guage Root Valves are for application where more than one inlet or outlet is required to used also as a guage valve or a sampling valve. These valves are simple and economical for installing pressure swiches and transmitter gauges. This Valves are Long body for insulation clearance.

Features

• One Piece Barstock Forged Body for high strangh and fully safety.
• Bonnet lock prevents accidents disassembly.
• Stem threads rolled and hard plated provides maximum service life.
• Two Part Stem tip, stellited and hardened provides excellent flow control and ensures buble-tight shutt off.
• Non Rotating Vee / Ball Tip design: Which forms a bearing joint with the stem eliminates rotation between plug & seat at closure. This prevents scoring and gailing up the valve seat and ensure long life in repetitive shutt off service.
• Packing below stem threads prevents stem lubrication washout and isolate threads from system fluids.
• Hard seat designed to reduce packing friction giving very low torque operation.
• Packing material – PTFE / Ccrafoil

Construction

• SS-316, SS-304, Carbon steel, Monel & Inconel.

The Sophisticated and costly instrument used in complex plants need to be installed according to certain carefully laid down safeguards using selected and reliable accessories.

Most of the instrument valves produced without any adherence to the rigid codes of the instrumentation industry are unsafe to high pressure use. These Valves cheaply produced have common deficiencies:

• Their seal just an 'O' ring Spindle cannot take wear.
• Leakage due to galling at the tip Spindle Which rotates on closure is prone to galling
• Normally threads are in contact with process media.

AKI Needle Valve are specially designed to eliminate all the above deficiencies and produced under rigid qually control from basic raw material stage. Valves are precises machining on mordern machinery to provid high quality and low cost, to meet the exacting standards of our valuable customers.

Features

• All AKI Instrument valve including those used with instrument Air Feed Headers are produced for working pressure 6000 PSI.
• Stem design with no turning action on closure thus preventing galling.
• Threads Protected from process media.
• Forzed or Bar Stock Construction in straight or angel pattern with panel mounting type.
• Screwed bonnet, union bonnet and integral body bonnet construction, Valves.
• Metal to metal or stellited and non rotating tip stem for high pressure, Teflon seal for positive repetitive shutt off for low density gases and non lubricating fluide.
• Special Telfon as grafail packing for leak proof joint at various temperature.

Construction

Generally fabricated from forged / barstak. material in high grade stainless steel, carbon steel, brass and monel materials in variety of end Connection.

• ALL NPT threads to ANSI B2.1
• ALL BSP Parallel threads to BS 2779
• ALL BSP taper threads to BS 21
• Socket Weld design optional

For more info please refer the attached pdf file