The butterfly valve controls flow by using a circular disc or vane with its pivot axis at right angles to the direction of flow in the pipe. The butterfly valve is used both for on/off and throttling services.

Design Description:
• API 600 DESIGN • API 603 DESIGN FOR 150 LBS & 300 LBS • BOLTED COVER (PRESSURE SEAL COVER FOR 1500LBS) • SWING TYPE FOR HORIZONTAL OR VERTICAL LINES • RENEWABLE SEAT RING • INTEGRAL SEAT FOR 150 LBS & 300 LBS
Material:
• A216-WCB • A217-WC6 • A352-LCB • A351-CF8 • 351-CF8M • A351-CF3M
OTHER MATERIALS UPON CUSTOMER'S REQUEST
Ends:
• FLANGED ENDS • BUTTWELDING ENDS
Ratings:
ANSI
• 150 LBS • 300 LBS • 600 LBS • 900 and 1500 LBS
• JIS 10K, 20K, 30K, and 40K
• PN 16 and 40
Size:
• 2” - 24”

Design Description:
• API 602 DESIGN • OUTSIDE SCREW AND YOKE • BOLTED BONNET (PRESSURE SEAL BONNET FOR 1500LBS & OVER)• RENEWABLE SEAT RINGS
• RISING STEM AND NON-RISING HANDWHEEL
Material:
• A105 • A182-F11 • A182-F22 A182-F304 • A182-F316 • A182-F316L
Ends:
• SOCKET WELD ENDS • SCREWED ENDS • FLANGED ENDS
Ratings: ANSI • 150~800 LBS • 1500 and 2500 LBS
Size: 1/2” - 2”

The gate valve is a general service valve used primarily for on--off, non-throttling service. The valve is closed by a flat face, vertical disc, or gate that slides down through the valve to block the flow.
Design Description:
• API 603 DESIGN FOR 150 LBS & 300 LBS • API 600 DESIGN • OUTSIDE SCREW AND YOKE • BOLTED BONNET (PRESSURE SEAL BONNET FOR 1500 LBS) • FLEXIBLE WEDGE, FULLY GUIDED • RENEWABLE SEAT RINGS • RISING STEM AND NON-RISING HANDWHEEL • AVAILABLE WITH GEAR OPERATOR • AVAILABLE WITH ACTUATOR • AVAILABLE WITH BY-PASS VALVE
Material:
• A216-WCB • A217-WC6 • A352-LCB A351-CF8 • 351-CF8M • A351-CF3M
• OTHER MATERIALS UPON CUSTOMER'S REQUEST
Ends:
• FLANGED ENDS • BUTTWELDING ENDS
Ratings:
ANSI
150 LBS • 300 LBS • 600 LBS • 900 LBS • 1500 LBS
• JIS 1OK, 20K, 30K and 40K
• PN 16 and 40
Size:
• 2” - 24”

The globe valve effects closure by a plug with a flat or convex bottom lowered onto a matching horizontal seat located in the center of the valve. Raising the plug opens the valve, allowing fluid flow. The globe valve is used for on--off service and handles throttling applications.
Design Description:
• API 603 DESIGN FOR 150 LBS & 300 LBS • API 600 DESIGN • OUTSIDE SCREW AND YOKE • BOLTED BONNET (PRESSURE SEAL BONNET FOR 1500 LBS) • YOKE INTEGRAL WITH BONNET • LOOSE DISC • RENEWABLE SEAT RINGS • RISING STEM AND HANDWHEEL • AVAILABLE WITH GEAR OPERATOR • AVAILABLE WITH ACTUATOR
Material:
• A216-WCB • A217-WC6 • A352-LCB • A351-CF8 • 351-CF8M • A351-CF3M
• OTHER MATERIALS UPON CUSTOMER'S REQUEST
Ends:
• FLANGED ENDS • BUTTWELDING ENDS •
Ratings:
ANSI
150 LBS • 300 LBS • 600 LBS • 900 and 1500LBS
• JIS 10K, 20K, 30K and 40K
• PN 16 and 40
Size:
• 2” - 16”

ALFA a leading MFRS of specialized Industrial Valves offers, spring loaded. Full Lift Safety Relief Valve, In a verity of orifice.
"AIE" Safety Valve provides Relief from an over pressure condition Automatically, reliably and effectively ensures the maximum discharge rates, Protects expensive equipment's from dangerously high pressure.
ALFA knowledgeably designed & 100 % factory Tested " Zero defect " & mfg. under pressure rating of American Standard.
The Different size of orifice is available for different discharge capacity.
"AIE" Safety Valves are excellent for used on Steam Boilers, Steam Services on unfired Pressure Vessels, Accumulators, Cleanness and Distillers as well as on Compressors, Receivers, Burners, Dryers and others piping system.
Material: Cast Iron, Carbon Steel, SS 304/316, SS 304 L / 316L, Gunmetal etc.
Deasign: Self Actuating, Full lift type
Discharge: Angle, Straight
Bonnet: 0pen, Closed
Rating: 150 LBS X 150 LBS, 300 LBS X 300 LBS, 600 LBS X 600 LBS
Ends: Screwed, Flanged End
Size: ½" X ¾ " - 6" X 8"

Thermodynamic steam trap with an inbuilt strainer and a full stainless steel construction, best suited for header and mainline drains and drop legs. This trap with screwed ends is suitable up to 36 barg and with socket weldeble ends is suitable upto 42 barg and 425°C.
Salient Features:
• Complete stainless steel construction ensures better mechanical and corrosion resistant properties.
• The disc and seat, hardened by induction hardening process to about 45 Rc to enable withstand continuous water hammering Condition.
• Seat integral part of the body eliminates leakage - prone joints and gaskets.
• Condensate entry below the disc concentric to disc/seat ensures dean and parallel lift of disc with reference to seat, eliminating any localized wear and tear.
• An inbuilt strainer screen of adequately large area ensures long and trouble free operation.
Materials: ASTM A 105, ASTM A 182 F 304 /316
Ratings: 800 LBS, 2500 LBS
Ends: Screwed End / Socket Weld End / Flanged Ends
Size: 15mm - 50mm

Design Description:
• Y-PATTERN
• BOLTED COVER WITH DRAIN PLUG
• PERFORATED STAINLESS STEEL SCREEN
• AVAILABLE WITH 40 - 200 MESH SCREEN
Material:
• A216-WCB • A217-WC6 • A352-LCB • A351-CF8 • 351-CF8M • A351-CF3M
• OTHER MATERIALS UPON CUSTOMER'S REQUEST
Ends:
• FLANGED ENDS • BUTTWELDING ENDS • SCREWED ENDS
Ratings:
ANSI
• 150 LBS • 300 LBS • JIS 10K and 20K • PN 16 and 40
Size:
• 1/2” - 16”

The range of flush bottom valves are extensively used in flush tanks that are mounted at the bottom of the tank. Its is provided with PFA / FEP lined coating that is resistant to corrosion and can withstand high temperature.

We are designing and manufacturing superior quality pressure reducing valves that are provided with high pressure regulators that are easy to install, adjust & inspect. Its application areas include field regulator applications, high pressure industrial air or gases and many more.

Sight Glasses are devices that are normally fitted in a fluid line provide a visual indication of the system condition. A sight glass fitted after a trap will quickly show whether it is working correct and will save hours where a lot of traps discharge into a closed condensate return system. It is very essential if ball float steam traps with steam lock release (SLR) are to be adjusted properly.

Single Window and Double Window versions are available. The double window sight glass gives a clearer indication of flow, particularly if the sight glass has to be fitted in a position where it is difficult to see, such as underneath a machine.