Anala Pumps (S. J. Industries)

AWP/AWC series of centrifugal pumps in C.I, SS304, SS316, Alloy-20, Hostelloy-C, etc., are excellent for handling clean or slightly turbid, non-aggressive liquids. They are suitable for pumping condensate, including water upto 100^o C, irrigation, general water supply in agriculture, trade and Industries with favorable NPSH conditions.

Construction Features

Horizontal single stage volute casing pump’s dimensions correspond to DIN 24255 with end suction and top centerline discharge. Back pullout design enables to remove the rotor assembly without disturbing the pipelines. The supports feet are integrally cast with volute casing. The AWP/ACP range comprises of 31 pump types with 3 shaft sizes, which cover the entire range with maximum interchangeability. For pumps nut and bearings are interchangeable. Impeller is hydraulically balanced by back vanes, and in the case of larger impeller diameter by renewable wear ring and relief holes.

Technical Data

• Capacity Upto – 550 M3/hr
• Total head Upto – 100 Meters
• Speed Upto – 3600 RPM
• Temperature Upto - 160o C
• Casing Pressure Upto – 16 cm2
• Flanges Flange dimensions are according to Din 2532/2533. ANSI/BS is an option.
• Direction Or Rotation Moves clockwise from the    drive end
• Casing Pressure
• 16 Bars (Subject to total head of 100 Metres)
• Shaft Sealing
• Shaft

Our metering or dosing pumps are high precision positive displacement pumps, according to the API 675 standard for controlled volume pumping. The discharge can be varied from zero to maximum capacity while pumps are running or at rest. Our pump design makes it an ideal flow control tool in chemical process for feeding chemicals with high degree of accuracy under any discharge pressure conditions. These are of robust design, unmatched quality and offer considerable saving due to small space requirement, low installation cost, minimum maintenance etc.

Typical Characteristics

Our dosing/metering pumps have a capacity output which is digital in nature, linear in proportion to the length of the stroke and is almost independent of discharge pressure.

Pumps Head Design
Plunger type liquid-ends are suitable for non-hazardous liquids. Because of their simple design, they are quite economical. They can be provided with flushing connection. In case of molten liquids, steam jacketed heads can be provided. The jacket encloses the check valves and gland chamber. The valves are cartridge type and can be removed for servicing without dismantling the suction and discharge connections.

Diaphragm Pumps
Diaphragm type heads are suitable for service conditions involving hazardous, toxic, radio active or poisonous liquid, where product leakage is not at all permitted. The diaphragm is hydraulically actuated and has a long life, as it is always under hydraulic balance with the liquid being pumped on one side and actuating fluid on the opposite side. The function of the diaphragm is basically that of a partition. The diaphragm material is usually teflon or synthetic rubber. The system is safe guarded by in-built relief vacuum valve on the hydraulic side. For very severe duty condition or when handling slurry or hot liquids, double diaphragm and remote type heads can be provided.


Applications
Typical applications of our pumps are the accurate dosing and mixing of acids, alkalis, slurries, viscous liquids, etc. which may be pumped at elevated ambient or low temperature, twenty four hours a day. Our range covers everything from a single pump to a complete automated metering dosing system comprising of plunger and diaphragm pumps with metering ranges from three to 5000 L / hr. Pumps can be provided with up to twelve heads and all the necessary accessories can be provided with up to twelve heads and all the necessary accessories can also supplied.

Stroke Adjustment
The pump discharge is variable while pump is running or at rest from zero (0%) to full stroke by means of a precision machined crank equipped with a stroke length adjustment mechanism. The stroke of the pump can be controlled either - Manually (local) Automatic, electrically or pneumatically, (Remote)

Liquid End Material
Our parts can be offered in the following materials, which are mentioned below:

• Stainless Steel 304
• P.V.C.
• Stainless Steel 316/3162
• P.P.
• Steel
• Teflon

Special Features
Pumps can be offered in simplex, duplex or multiple heads, (up to Twelve heads) for handling different chemicals with a common motor, Each head would have independent connections and the capacity of each head can also be independently adjustable.

Capacity

• 0.5 to 5 HP
• 20 to 10,000 LPH
• Pressure 10 kg/cm2
• 0 to 100% stroke adjustment
• Liquid end materials available:- SS304, SS316, SS3162, PVC, PP and Teflon(PTFE)
• Pumps are available in simplex, duplex and multiple head
• Pumps are designed as per API 675 standard for controlled volume pumping

SS Gear Pump - Features

These are available in investment cast SS 316 and SS 316L material. The gears and shafts are nitrated and the DU bushes Teflon coated. They are wear resistant and can operate in temperature up to 200 deg C.

Recommended for Liquids

Viscous and corrosive liquids, mild acids, printing ink, dyes, sugar scrub, resin or pigments, slurry, glycerin, kerosene, vegetable, oils, honey admixture, edible oils etc.

Body	SS 316
Covers	SS 316
Gears	SS 316 nitrided
Shafts	SS 316 nitrided
Gland cover	SS 316
Seal	PTEF
Bracket	C.I
Bush	PTFE coated
Bolts	SS 304
Relief vlaue	SS 316

CI gear pumps - Salient Features

They are simple, silent, compact, efficient and economical. They are good for temperatures upto 90 deg C. High temperature various are available on request.

Applications

They are suitable for transfer of vegetable oils, mineral and animal oils, non-corrosive viscous and semi-visous liquids, lubricants like engine oil and gear oil, kerosene etc.

Casing	C.I or Gr 20
Covers	C.I. or Gr 20
Shafts	En9 H & G
Gears	En8
Shafts sear	Oil Seal
Bearing	Bronze bush bearing
Plug	Brass