As industry & telecom department is using multi source of supply and use a single suitable supply as their requirement by using change over switch. Increasing or decreasing the AC voltage on input distribution panel the efficiency goes very low about 60 to 65%. Due to this efficiency losses most of raw power goes waste as heat. It is lot of revenue losses to telecom department. When high voltage or low voltage crosses the voltage limit and attached equipment gets faulty, to overcome this type of problem we introduce our product Auto Change Over Unit.
Industries require three phases power to run their machinery. Some of them require continuous \ uninterrupted power to maintain their data. We introduce auto phase selector unit for those equipment whose supply is single phase. The single phase supply is selected automatically from three phases supply.
Auto Phase Selector introduces an automatic solution to overcome power fluctuation \ phase interruption by selecting next most healthy available phase to feed the equipment.
Batteries are major source of power backup for equipment running on this. These are also as heart of any critical equipment. The end user is concerned for using battery back up, he actually is not aware about the status of individual cell of battery, & this un- conciseness introduces un-required battery back-up failure in critical time. In the past time the battery monitor consisted of a voltmeter on the DC Bus, through some ground fault detection but 80% of all battery failures are connection path related i.e. any cell failure. So, the role of observation process has been introduced. In ever increasing spirals of demand and sophistication, everything including stationary batteries is fair game for some form of observation.
The battery manufacturer recommends the charging voltage in different mode as float mode charge mode and they also recommend the depth of discharge it means if a battery of 48V goes below from specified voltage it may be difficult to charge it again easily. Therefore, the life of battery decreases or battery may get damage. This creates back up problem for the equipments running on batteries. So to overcome this kind of problems our BHMP has been introduced, to give battery protection against deep discharging as a set of whole battery status.
The AMF unit is designed for Observation the Mains supply and control the Generator unit to reduce the Electric power failure condition. It will continue the supply to load either by Mains or by Generator unit (When mains is not available or out of range)
Line Regulation Unit is designed to provide stable voltage for operation of costly equipment on abnormal incoming mains and varying loads the system is controlled by micro processor to provide stable and continuous correction. There is low and high both type of correction provided. Its subtracted / added to keep the output voltage within set voltage without any introduction of waveform distortion. This Unit is useful for telecommunication, TV, Video Recorder, RADAR navigational Devices, Computer, Micro Scope, Photo Processing equipment etc.
The Communications and power equipment are housed at various locations away from Central office. It becomes mandatory to monitor and control that the system is working satisfactory. Power Automation System is the primary objectives to Energy & Manpower Saving, Reducing maintenance cost, increasing the life of equipment, maintaining operation schedule. The PAS unit is designed for Observation the Mains supply and control the Generator unit to reduce the Electric power failure condition. It will continue the supply to load either by Mains or by Generator unit (When mains supply is not available or out of range)
SMPS rectifiers works between 150V to 275V on single phase & 320 to 480V in three phases. PPU will connect the mains supply whenever mains will be available in range. If mains will come out of range, at that time this unit will disconnect the mains supply for power plant. So that power plant can work with out any trouble. If mains come either less then 150V or more than 275V, it means it is very dangerous for the equipment. It can damage the equipment. Surge Protector will also provided with this unit to protect against surges and as well as High and Low voltage.
Servo Voltage Stabilizer is designed to provide stable voltage for operation of costly equipment on abnormal incoming mains and varying loads the system is controlled by micro processor to provide stable and continuous correction. There is low and high both type of correction provided. Its subtracted / added to keep the output voltage within set voltage without any introduction of waveform distortion. This Unit is useful for telecommunication, TV, Video Recorder, RADAR navigational Devices, Computer, Micro Scope, Photo Processing equipment etc
Nirmal Electric Works Supplier of automation systems, control panel, electric control panel, heavy duty panels , industrial control panel, automatic control systems, capacitor control panel and power control centre.
Kerone Engaged in manufacturing of all kinds of ac drives, motor ac drives, motor controller ac drives, speed controller ac drives, torque controller ac drives and induction motor controller ac drives.
Rajashree International Manufacturer and exporter of plant control panel, programmable logic controller systems, motor control panel, panel, synchronizing panel, industrial control panels, distribution panel and variable frequency drive panel.
Processing...
