This is a non yellowing, non ionic softening agent used for treatment of cellulosic fibers, synthetic fibers and their blends. This can be availed in pourable form and can be applied by padding and exhaust method.

Application

AUXI SOFT NS is basically used to apply in both exhaust and padding method. The concentration of the chemical is determined as per the desired effect and for the kind of fiber. The chemical can be applied as a self finish or in combination with other finishing chemicals and optical brightening agents.

Specifications:

Appearance	: White pourable paste
Composition	: Fatty Acid condensation product
Ionicity	: Non - ionic
pH of 1 % soln	: 6 - 7
Solubility	: Can be diluted with water to any extent
Compatibility	: Compatible with Anionic as well as cationic finishing agents

AUXI IN HPLF is a low foaming wetting agent which has good washing capacity and excellent wetting properties. This chemical can be applied on all native and synthetic fibers in all cleaning procedures. This suits for installation with spraying devices and where small amount of foam is required. This chemical is dissolved by pouring warm or cold water over it. This can be availed in the following specifications:

Chemical character	: Modified fatty alcohol ethoxylates
Appearance	: Colorless, clear liquid
Ionic character	: Non - ionic/anion active
pH-value of a 10% Solution	: 5.0 - 7.0
Specific weight at 20 ' C	: Approx. 1.0
Stabilities	: AUXIIN HPLF as well as the watery solutions prepared of it are stable to the usual concentrations of acids, alkalis, metal salts, oxidation and reduction agent as well as to hard water. When preparing the stock liquors the product gives turbid solutions since part of the substances are emulsified. AUXIIN HPLF is not sensitive to frost.

AUXI IN AWN is a good stabilizer for peroxide bleach under higher alkaline pH and it does not foam.

Applications

Usually 10-30% AUXI IN AWN is used and the calculated amount in ml of peroxide is used. It can be applied by both exhaust and cold pad batch method.

AUXI IN AWN can be applied both by exhaust as well as by cold pad batch method.

Suggested Concentration of AUXI IN AWN

• Jigger0.5-1% AUXI IN AWN on weight of material
• Winch 1-2g/l AUXI IN AWN

Cold Pad Batch Method
7/10/2003 g/IAUXI IN AWN

The quantity or the concentration of the chemical may vary as per the quantity of alkali and peroxide according to time, temperature and quality of fabric to be bleached.

Properties:

Appearance	: Light yellow brown liquid
Composition	: Based on organic compounds
Ionicity	: Anionic
pH	: 6-7
Dilutability	: Miscible with water in any proportion
Storage	: Stable for atleast 6 months if stored in cool place

AUXI IN SOFT CS is a cost effective softener and is available in pourable form.

Application (Dissolving Method)

The chemical can be applied by both exhaust as well as padding method. AUXI SOFT CS is dissolved by steadily by adding it up while stirring 10-20 times the weight of water at 60-70'C. The stock solutions are stable and can be diluted with water as per the requirement. Concentration depends on the kind of fiber and the effect desired.

Properties

Appearance	: Creamish white pourable paste
Composition	: Fatty acid condensation product
Ionicity	: Cationic
pH	: 4-5
Solubility	: Can be diluted with hot or cold water to any extent
Compatibility	: Compatible with non ionic finishing agents but not compatible with anionic finishing agents

AUXI IN DESAN kills metal ions like Fe and is phosphate-free, polymer based sequestering agent with dispersing properties.

Application - Dyeing

AUXI IN DE SAN can be applied in both exhaust baths and in padding processes.
In the exhaust dyeing of reactive with prior addition of 1-2% of AUXI IN DE SAN in the dye bath maintains Ca and Mg ions. These ions may interfere in the dyeing process, particularly when using hard water.

In the dyeing of reactive during the cold pad-batch process, the adding up of 2-3 gm of the chemical in the padding solution gives dyeing with fine constancy and solidity for the similar reason.

Addition of 2 gm/I of our auxiliary chemical during the washing of reactive dyeing facilitate speedy removal of unfixed dye. This leads to improve rub fastness of the dyeing. During washing-off in cold pad-batch dyeing, the addition of 2 gm/I of our chemical in the washing bath assist in the quick removal of sodium silicate from the fabric.

Properties

Appearance	: Clear liquid
Composition	: Synergistic mixture of organic compounds
Ionicity	: Anionic
Compatibility	: Compatible with anionic and non-ionic compounds. Can also be used with mildly cationic compounds after ascertaining compatibility
pH	: 8.0 + 1.0
Dilutability	: Can be diluted with water in all proportions
Solid Content (%)	: 27 + 1.0 (drying at 140’C)
Storage Stability	: 1 year if stored in closed containers, in a cool dry place, away from heat and direct sunlight

AUXI IN SOLJET is an anti Creasing & Lubricating chemical with the following specification:

Nature	: High-molecular-weight polymer in aqueous solution, non-ionic
Physical form	: Clear to slightly hazy. Somewhat viscous, colourless liquid. Readily Pourable
Ionicity	: In the original sealed containers at temperature between 5’C and 35’C. AUXI IN SOL JET has a shelf life of atleast 12 months. Once containers have been opened, the contents should be used up quickly. Containers should be closed tightly after use

Properties

Density	: Approx 1.0 g/cm3 at 20’C
pH	: 5.5 – 7.5 (100 g/I in water at 23’C)
Viscosity	: Intrinsic viscosity, approx, 1000-2000 mPas (100/min, rotational viscometer, open vessel at 20’c)
Solubility	: Miscible with water in all proportions to form a clear solution
Action	: AUXI IN SOL JET has unusual viscosity properties

AUXI IN WAA is a low foaming detergent and dispersing agent for reactive dyeing. This is appropriate for pre treating and bleaching cotton and fiber blends with man made fibers.

Specification

Appearance	: Clear, Colourless Liquid
Composition	: Mixture based on aionic and nonionic surfactants with defoaming additives.Contains no silicone or mineral oils or solvents
lonicity	: Anionic
Solubility	: Unlimited solubility in water without gelation, can be added direct via metering pumps
Resistance	: Resistance to caustic soda solution containing up to 80 g/l caustic soda

AUXI IN JET B CONC is a low foaming wetting agent for consistent dyeing. These can be used for high detergency even with stubborn soil. This has a perfect wetting action.

Specifications

Appearance	: Slightly translucent, colorless, viscous liquid
Composition	: Mixture of ethylene oxide condensates with other chemicals
Ionicity	: Mildly anionic
Compatibility	: Compatible with chemicals likely to be used in scouring and bleaching
pH	: 7.0 + 1.0
Storage Stability	: One year, if stored in closed containers in a cool, dry place, away from direct sunlight

AUXI IN DFTis a levelling agent which is used in metal complex dyestuffs.

Specifications:

Appearance	: Brown Liquid
Composition	: EO Condensation of mineral oil
Density at 20'C	: 1.21 g/cm3
lonicity	: Non-Ionic
Reaction	: Alkaline (about 9)
Dilutability	: Dilutable with water in any ratio
Resistance to	: Acids, Alkalis, Electrolytes, Water hardness - good under actual conditions of use
Storage Stability	: Freezes below -20'C; fully usable after thawing
Compatibility with	: Anionic compounds, Cationic compounds, Non-Ionic compounds - compatible
Foaming Tendency	: Low foaming

Application Properties:

The AUXI IN DFT offered by us aids in migration, improves levelling properties of vat dyes & enable shade or shade depth differences which are to be levelled out during normal dyeing cycle ensuring no dye loss in the process.

For closely woven fabrics & cross winds, we acheive excellent dye penetration with non-foaming AUXI IN DFT. For particularly difficult cases, the effect are assisted by raising temperatures to 70-80'C & somewhat prolonging dyeing times.

AUXI IN DEFOAMER is white in color, odorless, non toxic and non flammable, is compatible with common sizing agent and is easy to handle. This is used as a defoamer for paper machine to enhance sheet formation and widely used in paper industries and effluent treatment plants for industries such as medicine, textile, fertilizer etc.

Preparing Emulsion- Prepare 2 to 5 GPL solution with hot water (60-70°c). 0.5 to 1.5 kg chemical is required per ton of paper used as defoamer in paper machine.

Properties

Color & Appearance	: White thick liquid
pH 5% solution	: 7.0 to 8.0
Nature	: Non-toxic forms Anionic
Solubility	: Aqueous forms milky white emulsion

Packaging

Defoamer is packed with 50 Kg or 200 Kgs packing.

Note: The defoamer is must be added consistently in the form of thin stream in the paper machine. The actual quantity of defoamer is required according to the ton of paper upon the paper machine.

AUXI BOND RESIN increases bursting and tensile strength, enhances scott internal bond or ply bond. It improves stiffness and wax pick. This is a paper additive which offers dry strength property by effective electrostatic absorption. This property can not notice in normal products. This can be used to improve the dry strength of paper from bleached and kraft pulps.

Mode of Application

8-10 Kg per ton of paper used at mixing chest

Properties

Color & Appearance	: Pale yellow to colorless syrupy liquid
pH	: Products 7.0 – 8.0
Solubility	: Soluble in cold water giving clear solution
Viscosity	: Low to medium
Shelf Life	: Minimum three months
Solid Content	: 55%

Mode of Use

AUXI BOND RESIN should preferably be diluted with about three time quantity of water previous to make use of in order to ensure a better distribution of product in the fibers. Due care should be taken that the diluted product is not stored for long period. With the use of AUXI BOND sufficient alum is added to the stock to ensure maximum retention of product in the paper. The acidity of the stock is accustomed so as to bring the pH of the slurry within the range of 4.5 to 6.5 and if alum and hydrochloric acid or Sulphuric acid is made to adjust the pH of backwater and drying temperature of the paper.

Benefits:

• Better dry strength properties
• Improves the smoothness
• Improved stiffness
• Better internal and surface sizing

Packing: 50 Kg HDP Jars

Salient Features:

• Very good dry and wet crease recovery
• Built-in and balanced catalyst system
• Low free formaldehyde content
• Improves dimensional stability
• Fibre protective system guards against excessive strength loss
• Compatible with all chemicals
• Does not impair the light fastness of dyeings

Specifications:

Appearance	Colourless Liquid
Composition	Modified DMDHEU resin
pH	3-4
Solubility	Can be diluted with water to any extent
Compatibility	Good with usual resin finishing chemicals