Teflon® /Fluoropolymer /ECTFE (Halar)/PTFE/PVDF/FEP/PFA Thick Coating- Blion

 BLION^TM-A pinhole free homogeneous thick coating of PVDF (KYNAR), FEP, PFA, ETFE, ECTFE (HALAR). It has the extraordinary chemical resistance on chemical equipments parts. Any articles of intricacy shape can be processed. Thickness from 500 to 1000 microns. Any articles of intricate configurations can be processed.

Properties:

• Temperature ranges from -100°C to +260°C.
• Withstands impact force and elongation up to 30%.
• Non-stick, Non-toxic, Electrical insulation, Anti-static and Release-surface.
• Resistant to almost all chemicals and solvents.

Typical Application:

Vessels	Autoclaves	Process Control equipment
Agitators	Sight Glasses	Centrifuge Housings
Stirrers	Heat Exchangers	Valves
Hooppers	Pressure Filters	Bends
Thermowells	Heating Coils	Tees
Spindles	Steam Ejectors	Floats
Dip-Tubes	Boiler dish	Flanges
Implellers	Nuclear Parts	Springs
Pump Housings	Large Parts	Reducers
Manway Covers	Large diameter pipes	Mushrooms

Fluoropolymer (PTFE)/ Teflon® / XYLAN® Coated Fasteners, Studs, Nuts, Bolts, Washers best suited for installations in offshore platforms, petrochemical and chemical plants, installations near the sea and in corrosive environments.

The resin-like bonded coating provides a low coefficient of friction and excellent resistance to many chemicals and acids.

PTFE dry film provides lubricity, thus preventing galling in breaking out.

• Fasteners, stampings and many other parts are coated with a material that contains Fluoropolymer / PTFE ( Teflon® / Xylan®).
• With the PTFE added to the coating it creates superior corrosion resistance and helps prevent gauling of threaded parts.
• The corrosion resistance is up to 750+ hours in a ASTM B117 salt fog test, depending on the coating being used.

Since 1972, with the introduction of FLUOROPOLYMER coating in America, TEFCOTTM coated studs bolts and nuts are widely used for enhanced corrosion resistance, permanent thread lubrication and consistently low applied torque to induced tension (clamping load).

Since then, almost all international petrochemical, oil drilling rigs and chemical process industries have specified these studs for both offshore and land based applications.

Apart from these XYLAN® PTFE coated B7 stud, bolts are installed under sea splash zones and chemical environments with great success.

Various Tests are undergone on XYLAN® /PTFE/ FLUOROPOLYMER - TEFCOTTM coated Studs, Bolts & Nuts.

• Acid Test Subjected to 720 Hours
• Caustic Test Subjected to 12.5 pH Caustic for 720 Hours
• Bromine Test exposed to Bromine Solution for 720 Hours
• Salt Fog Test Subjected to 720 Hours

Non-stick, Non-wetting, Anti-static, self-lubricating, heat-resistant properties, thickness from 25 microns and above. Very low adhesion to most materials, excellent water repellent, low-coefficient of friction, chemical inertness, and unusual thermal stability. Temperature resistance -100°C to +260°C. Not attacked by corrosive chemical or strong solvent.

Non-Stick: Very few solid substances will permanently adhere to TefcotTM coating and while tacky materials may show some adhesion, almost all substances release easily.

Non-Wetting: TEFCOT^TM surface are both oleo phobic and hydrophobic, they are not readily wet, clean-up is easier, more through and in many cases self-cleaning.

Heat Resistance: There is no decomposition of TEFCOT^TM below 250oC, insignificant decomposition between 250o and 300° which requires no special precautions.

Low Coefficient Of Friction: The coefficient of friction of Tefcot^TM © is generally in the range of 0.05 to 0.20, depending on the load sliding speed.

Cryogenic Stability: TEFCOT™ will withstand severe temperature extremes without loss of physical properties.

Unique Electrical Properties: Over a wide range of frequencies, TEFCOT^TM has high dielectric strength, a low dissipation factor, and very high surface receptivity.

Chemical Resistance: TEFCOT^TM is normally unaffected by chemical environments. The only chemicals known to affect all are the alkali metals and highly reactive fluorinating agents.

Typical Application
Textile Cylinders	Heater body
Biscuit Rollers	Guide Rollers
Conveyor Belt	Camera Parts
Volumetric Feeder	Instrumentation
Cylon Hopper	Iron Sole Plates

Polyamide/ Nylon/ PP/ PVC Coating for Defense, Electronic Industries PLASCOT -

Modern new approach the plastic coating to combine metals and of plastic into a single functional part.

Various sizes, shapes and intricacy can be coated with plastic Powder like Polyethylene, PVC, CAB, Plastisol, Epoxy, Polyester, Nylon, PTFE, PP, PU etc.
Any article of intricate configuration can be processed. It ranges form 250 to 1000 microns. Wide color range.

Properties:

Metals can be insulated, decorated, self-lubricated and protected from chemicals. Temperature ranges from -1000C to +2600C. Withstands impact force and elongation upto 30%.

Typical Application:

Automobile parts , Medical Parts ,Door Handle, Wheel of valves, grills etc.

Application On Various End Uses:

 Furniture, electrical apparatus, domestic appliances, door handles, window grills electroplating jigs, cable trays, wire racks, crates, tool handles, exhaust fans, picking basket, brackets, machine guards, junction boxes and parts like machinery, chemical, hospital orthopedic, automotive, building, air conditioners, medical surgical parts like forceps, seizures etc.

TEFVARTM - Its PTFE moulded semi-finished products like rods, cylinders, bush, blocks, sheets, tapes, etched cloth, tubes, pipes, magnetic stirrer and beakers. Available unfilled or filled like glass, graphite, bronze. Available as per the required size and dimension. PTFE Silicone Adhesive Tape available in extruded and skived films. Any width in length of 36 yards. Standard Thickness of 100 microns and also in other thickness TEFGLASTM - A combination of PTFE plus glass fiber without and with silicone adhesive. Width is 1000 mm and in continuous length. Glass cloth contribute excellent strength and dimensional stability, exhibit essentially zero flow under heat and pressure and are highly resistant to cut-through. Also in tape and belt form.

Properties: There is no known solvents which can react with this materials. Temperature resistance from - 100°C to + 260°C and also resist upto 300oC for a short duration. Non-stick, non-wetting, self-lubricating, heat resistance and electrical insulation properties.

Typical Application: Industries like Chemicals, Drugs, Pharmaceuticals, Electrical, Electronics, Communication, Fertilizers, Mechanical, Engineering, Pesticides, Petrochemicals, Nuclear Power, Oil, Exploration, Defence, Railways, Aerospace, Civil Construction, Food Processing etc.

FUROLINTM - PTFE lined steel pipe size from 25 to 150 mm NB length of 3000 mm. Used for both vacuum and pressure condition. Also supplied 900 and 450 elbows, tees, reducers, reducing flanges, blind flanges, spacers dip pipes, spargers and thermocouple.

Properties: Resistance to virtually all chemicals and oxidizing acids high thermal stability. Suitable for continuous temperature from -30°C to + 200°C. Non- stick, low co/efficient of friction, excellent insulating properties, Low weather ability and thus non- aging.

Typical Application: Industries like Chemicals, Drugs and Pharmaceuticals, Electrical, Electronics and Communication, Fertilizers, Pesticides, Petrochemicals, Nuclear power, Oil Exploration, food Processing, Defense, Aerospace etc.

POLYPORTM - Porous Plastic Filter Material of Polypropylene, PTFE, HDPE, Cellulose Acetate, Polystyrene ranges from 5 to 250 microns. Form of rods, hollow pipes, sheets and joined parts of porous with a non-porous plastic and can be moulded as per your drawing and dimension.

Material: POLPOR makes its porous plastics from many thermoplastic polymers including: Polypropylene (MGF), Polyethylene (DPL), Polyvinylidene Fluoride (PVF), Ethylene-Vinyl Acetate (EVA), Styrene Acrylo Nitrite (SAN), Polyurethane (PUR), Polytetrafluoroethylene (TFE), Polystyrene (PTR), Cellulose Acetate (CAB).

Availability: Porous POLYPOR™ are available in various configurations. These include Sheets, Rods, Discs, Hollow Candles, Threaded Adaptors, Tubes (open ended or fitted with caps flanges, threaded adaptors etc) Cones etc. Sheet can be reinforced by mean of a perforated metal sheet, which has a negligible effect on pressure drop.

Applications: Porous POLYPOR™ plastics are used throughout industry, medicine and the home; for applications ranging from noise reduction to air, water and chemical filtration; from marker pen tips to automotive battery safety vents; from surgical implants to clinical laboratory filters.

• Applicators
• Air regulator filters
• Aquarium Aerators
• Biomedical Filters
• Breather Vents
• Desiccant holders
• Controlled metering device
• Marker Tips
• Fragrance reservoirs
• Membrane support media
• Foaming Device
• Reagent Filters
• Pneumatic Mufflers
• Blood Serum
• Biological Sewage Cleaning
• Pneumatic Mechanical conveying as aeration flight conveyors in cement Industry
• Fine Division of Gases in Liquid
• Muffing
• Silencing the Insulation
• Diaphragms for electrochemical processes

High Performance Fine Bubble Membrane Diffuser For Waste Water Treatment Aeration - POLYFLEX & POLYPOR UNIQUE DESIGN Blinex’s Polyflex & Polypor unique open-end tube design diffuser allows water to completely fill the diffuser support tube, thus eliminating diffuser buoyancy and not allow diffuser to bounce during operation and there is not breakage / failure of nipple end connection.

Properties: Filter the finest suspended particles. The cartridges have uniform pore size, smooth surface, lightweight, odorless, tasteless, non-toxic, resistant to shocks and impacts. The unit withstands the pressure upto 150 PSI. The flow rate form 4 to 15 LPM in different microns cartridge.

Comparison:

FINE BUBBLE MEMBRANE DIFFUSERS	FIXED AERATOR	FLOATING AERATOR
SOTE 5.0 - 7.6 Kg O2 / kwh	1.2 - 3.1 Kg O2 / kwh	1.2 - 2.2 Kg O2 / kwh
50% Power Savings	Power consumption is high	Power consumption is high
Trouble free operation	Regular maintenance	Regular maintenance

Application:

• Bio-logical waste water treatment
• Used in streams & fish ponds (Aquaculture)
• Activated sludge waste water aeration
• Industrial waste water treatment plant
• Municipal waste water treatment plant
• Waste water ozone diffusion
• Oxygenation for sludge stabilization Re carbonation, Nitrification, Grit tanks, Grease removal and Floc-Agglomeration
• Contact aeration system Sequencing batch reactor (SBR)
• Lagoons & Channels

ADVANTAGES:

• High Oxygen transfer efficiency
• Self cleaning operation
• Fine bubble formation
• Non-clog operation
• Intermittent operation without water back flow
• Easy & quick to install
• No moving part - assures safety

BLINEX^TM Porous Products Group offers a line of standard products in a variety of materials, thickness and grades suitable for a wide range of applications.

• Polyethylene (PE) is offered in Extra Fine, Fine, Medium and Coarse grades.
• Polypropylene (PP) is available in Medium and Coarse grades.

The sheet grades in this product line have an average mean pore size in the 7-150 micron range with void volumes of 35-50%.

BLINEX^TM Porous Plastics are naturally hydrophobic, but aqueous solutions which can be forced through under pressure. If a gravity flow of aqueous solutions is desired,

BLINEX^TM can make the sheet hydrophilic with a special treatment procedure.

APPLICATIONS

BLINEX^TM Sheet materials are widely used for filtering, diffusing, venting, wicking, fluidizing, air conveying and as membrane supports. Specific applications include column chromatography supports, ion exchange resin support, battery flame arrestors, fluidized bed air pads and reservoirs for liquids.

Materials Handling Sheet:

BLINEX^TM Material Handling Sheet is a special high density polyethylene porous plastic that has specific usage in fluidizing/powder coating and material handling/conveying applications including:
Fluidizing Board –

• For powder coating, bulk pharmaceutical processing and food processing.
• Fluidizing Air Pads – assisting in the unloading of conical storage silos/bins and railroad or truck hopper cars.
• Air Conveyors – levitating and conveying of powders such as coatings, flour and grains, pigments, cement, fertilizers and lightweight objects, such as stampings, films, electrical components and semi-conductor chips.

Polypor^TM - This recently developed material, which is suitable for all sorts of medical device. When application in medical requires a filter, vent, wick, diffuser, support medium or self-sealing material first consider the Polypor^TM Porous Product Line. The advantageous of this product are it is harmless from physiological point of view and Sterilized in an autoclave (up to 130°C), which will not react with any Acids or Bases and we can supply it in any size and shapes, in pore size ranging from 1 to 100 micron. This unique material offers you the venting or filtering characteristic of our typical porous material-until the material comes in contact with an aqueous solution. When a liquid such as water or blood, comes in contact with the material it seals off the flow completely. These liquid barrier vents are ideal when used in applications such as catheter vents and aortal syringe vents.

Properties:

The structure of porous plastic has an intricate network of open celled omni directional pores in average size from 0.8 microns to 200 microns. The products are available in multitude of configuration to meet your own design requirements.

Typical Application:

Air regulators filters, Aquarium Aerators, Biomedical filters, Breather vents Marker tip, Controlled metering devices, Foaming devices, Water conditioning filters, Pneumatic mufflers, Blood serum filters, Industrial filters, Filtration support media, Oxygen humidifiers, Fuel filters, Battery flame arrestors, ETO vents, Powder Handling acoustic, Absorption/Dab sorption media eg Wicking material for controlled application of liquids or evaporation of volatile substances, Battery venting, Vacuum chucks conveyors, Wicking-Diffusing devices, Ink transfer in printing machines, Fluidizing powders.

We at BLINEX FILTER COAT PVT LTD also have a ready stock of various Imported Filter Candles for various application. Following Cartridges will be available with us:

• Spunfibre Polypropylene.
• Depth Polypropylene Wound.
• Depth Polypropylene Wound.
• Cellulose / Polypropylene / Polyester PTFE Pleated Membrane.
• Porous Activated Carbon / Silver Impregnated Block.
• Porous Plastic with Granular Activated Carbon.
• Chloride, Lead, Bacteria, Mercury Removing Cartridge.
• Resin Bonded Polyester Fibres.
• Activated Carbon Impregnated Cellulose.
• Micro Fibre Glass & Polyester Pleated.
• Highly Asymmetric Membrane.

80% of diseases leading to death have water as the main factor for their cause. So what you really need in today's unhygienic water conditions, is a 100% effective water purifier that not only stops the germs from breeding, but also destroys them on contact. Allow us to introduce to 7-stage . A purifier uses the same technologies that are employed by NASA- USA, to eliminate a wide range of bacteria, viruses and other harmful micro-organism. It involves the latest silver / iodized carbon block and purification resin technologies and a unique seven contact process for making your drinking water micro biologically pre. The bottom line is we'll make you germ free.

NASA - USA Resin Base Technology (Disinfectant)

Silver Iodised Carbon Block Technology (Bactericidal)

Certified by reputed hospitals & laboratories

Kills virus, bacteria and other micro organisms

7 Stages of Filtration

No Plumbing (attaches to kitchen tap In seconds)

No Electricity

On Line & Portable

No AMC (Self Maintenance)

Additional Features of Model 200 Duplex:

Removes Chlorine, Iodine & Odour

Hard Water Softner and Flourlde Candle which can be used as an when required