• Steel: Synthetic Zinc Phosphate / Synthetic Zinc Chromate Primer
• Aluminum and Galvanized Iron: Epoxy Etch primer
• Wood & Fibre-board: Synthetic Pink Primer or Aluminum Primer.
• Cement & Brick: Synthetic Wall Neutralising Cement Primer
• Method of application: Brush, Roller, Spray
• Notes on Airless Spray: Tip Range 13-19 thou. Total Output fluid pressure 2500 - 3000 psi. (176 - 211 kg/sq. cm.)
• Thinner : G.P.Thinner No.1

By making use of qualitative raw material, we manufacture architectural coating. This gives an attractive look to the surfaces and never fades for a long time. We can provide our coating as per various industrial requirements. These are acclaimed for their features such as scrub and stain resistance, excellent color retention property and washable. Following are various types of paints offered by us:

• BPL Wall Neutralizing Cement Primer. (For Interior)
• BPL Premium Emulsion Paints. (For Interior All Shades)
• Super Acrylic Emulsion Paints. (For Exterior- All Shades)
• BPL Wall Neutralizing Cement Primer. (For Exterior)
• BPL Premium Acrylic Distemper (For Interior All Shades)

We offer Epoxy coatings, which is our Epoxy Polyamide Cured Hi-Build Epoxy Finish. Our coatings is a two pack polyamide cured High Build epoxy coating, which specially prepared for use in painting storage tank exteriors exposed to humid, saline and chemical environment. The coating helps to resist crude and refined petroleum oils and it gives protection against chemical fumes and spillage of alkalis, salt, solvents or mild acid solutions. These coating are widely used in heavy duty systems for power plants, refineries & petrochemical units, gas plants, fertilizer plants, chemical plants, pulp & paper mills. The preparation for various surfaces is given below: 

For new concrete surface, should be ensured that the surface is cured for minimum 2 months. Remove laitence, loose surface powder by light sand blasting. If blast cleaning is not feasible, roughen the surface by acid etching with 10% Hydrochloric Acid solution followed by thorough freshwater hosing to remove any residual acid. The surface should be perfectly dry and clean before applying primer.

For old concrete surface: Remove grease and oil by solvent wiping. Remove water-soluble contaminants by fresh water hosing. Roughen the surface by acid etching, if light sand blasting is not feasible. The surface should be absolutely dry and clean before applying primer.

APPLICATION DETAILS

Method of application:

Air less spray / Brush Airless spray essential for the required high film build and uniform finish

• Tip Range 21 - 26 thou.
• Notes on Airless Spray:
• Total output fluid pressure - 2500 - 3000 psi. (176 - 211 kg/sq.cm.)
• Pot life : 2 - 4 hours
• Thinner : SPL No.1

With the help of our modern manufacturing facility, we manufacture chlorinated paints. This includes BPL Hi- Build Chlorinated Paints. (All Shades) and BPL Hi- Build Zinc Based Primer for Chlorinated Paints. These are specially formulated to withstand harsh interior and exterior condition including oil, harsh chemicals, salt water and fungus. Our chlorinated paints are suitable for use on wood, non ferrous metals, iron and steel, concrete, brickwork and plaster.

we are offering industrial primers such as synthetic zinc phosphate grey. These give excellent performance and are resistant to corrosion. Our primers are based on phenolated alkyd medium and zinc phosphate pigment and give good performance on mild steel surface in hard humid and coastal environment. These primers are compatible with various types of top coats such as synthetic enamels, bituminous paints, aluminum paints as well as chlorinated rubber paints.

Surface Preparation:

Steel Surfaces:

Surface should be perfectly clean and dry before applying synthetic zinc phosphate primer. Degrease and blast clean to sa 2â½ grade minimum of swedish specification sis - 05 - 5900 - 1967. If blast cleaning is not practical make full use of mechanical tools along with manual cleaning and wire brushing to remove loose rust/scale to st 2 or st 3 grade of swedish specification.

Application Details:

• Method of application: brush /roller /spray.
• Notes on airless spray: tip range 15-21 thou. Total output fluid pressure - 2500 - 3000 psi. (176 - 211 kg/sq. Cm. )
• Thinner: g. P. Thinner

• Pipelines
• General structural steel
• Mining and machinery industries
• Refineries & petrochemical installations
• Tank exteriors
• Bridges, cranes, towers.

We offer polyurethane paints including polyurethane aliphatic finish. These are available in a two pack aliphatic acrylic polyurethane high gloss top coat with excellent weathering resistance and color retention properties. Due to its toughness and chemical resistance properties, it finds extensive use in coastal and chemical environment. Our paints are widely used in fertilizer plants, oil refineries, petrochemical units, marine installations, chemical plants, transportation industries, power plants, rail coach & chemical wagon exteriors and offshore structures.

 Following are the preparation for various surfaces:

STEEL SURFACES:

Surface should be perfectly clean and dry before application of appropriate primer. Degrease and blast clean to Sa 2½ grade minimum of Swedish specification SIS - 05 - 5900 - 1967. If blast cleaning is not practical make full use of mechanical tools along with manual cleaning and wire brushing to remove loose rust/scale to St 2 or St 3 grade of Swedish Specification.

CONCRETE SURFACES:

For new concrete surface: Make sure that the surface is cured for minimum 2 months. Remove laitence, loose surface powder by light sand blasting. If blast cleaning is not feasible, roughen the surface by acid etching with 10% Hydrochloric Acid solution followed by thorough freshwater hosing to remove any residual acid. The surface should be perfectly dry and clean before application of appropriate primer.

For old concrete surface: Remove grease, oil etc by solvent wiping. Remove water-soluble contaminants by fresh water hosing. Roughen the surface by acid etching, if light sand blasting is not feasible. The surface should be perfectly dry and clean before application of appropriate primer.

Method of application:

• Conventional Spray / Airless spray .Brush/ Roller for touching up small areas only.
• Notes on Airless Spray:
• Tip Range 18 - 21 thou.
• Total output fluid pressure - 2200 - 2500 psi. ( 155 - 176 kg/sq.cm.)
• Pot life : 2 - 4 hours
• Thinner : P.U.Thinner No.1

Supported by our efficient team of personnel, we manufacture heat resistant paints to our customers. Our heat resistant aluminum paints can resist heat up to 250°C. These are available in high lustre two pack aluminum paint with remarkable protective properties. Our paints can be used as heat resistant coating for chimney stacks, Pipes, Petro-Chemical & water tanks, boiler fronts, duct work, piping and furnace structure. These paints give good performance in external and internal application in offices, buildings, factories, warehouses and industrial plants. Due to its higher reflectance value, this paint has special use in coating exterior of storage tanks in oil industry      

Surface Preparation:

Steel surfaces:

Surface should be perfectly clean and dry before painting. Degrease and blast clean to Sa 2½ grade minimum of Swedish specification SIS - 05 - 5900 - 1967. If blast cleaning is not practical make full use of mechanical tools along with manual cleaning and wire brushing to remove loose rust/scale to St 2 or St 3 grade of Swedish Specification. As heat resistant coating above 100°C, paint to be applied directly on cleaned metal surface free from any rust and remnants of any old coating. For other uses (Below 100°C) the paint should go on appropriate primers.

Application Details

• Method of application: Brush / conventional spray
• Thinner: Thinner 1576

With the help of our advanced manufacturing facility, we make road marking paints. These paints are acclaimed for their feature of heavy abrasion resistance. We can provide our marking paints in various quantities as per the requirements of the customers. Our different type of paints for different colors is given below:

• BPL Hi- Build Road Marking Paints. (Solvent Thinnable) White / Golden Yellow
• BPL Hi- Build Road Marking Paints. (Water Thinnable )White / Golden Yellow
• BPL Hi- Build Special Road Marking Paints. White/ Black/ Golden Yellow

We provide chimney paints, which are manufactured from silicone resins pigmented with aluminum flake for usage at more than 500°C. Our paints are widely used in buildings, factories and structures. These can withstand adverse weather conditions and will not fade for long years.