IndiaMART.com
Indiamart

  • logo
  • Chromline Equipment Company

    Mumbai, Maharashtra

  • Year of Establishment: 1993
    IndiaMART Member Since: 2011
    Products [62]

    Mobile: +(91)-9967597352

Testing Tool For Electric Appliances

Testing Machine Tool For Electric Appliance This tester is specialized in testing the flexing endurance between power cord and blades, and is capable of testing the flexibility resistance of the cord itself. Samples are to be secured in the jaws of the flexing apparatus, and cord is to hang vertically with the weight tied on the lower end of it. The rotating jaws are to be adjusted to rotate to the angle of 90 degree to each side of the centered position.

Megohmmeter

Megohmmeter


GT-1864
This instrument measures the resistance of various conductors. The test voltage can be set to any value from 10VDC to 109VDC in 1-volt steps and to 1090VDC in 10-volt steps. Thus it can be set to any common, or uncommon test voltage for ceramic, mica or paper capacitors, or other devices. It is supplied in a convenient, portable, Flip-Tilt case that is a stand for the meter louse and protects it in transit and storage.

Please refer to the attached PDF for detialed information.


Convection And Ventilation Aging Oven

Convection And Ventilation Aging Oven


GT-7017-U
This tester is designed to test rubber & plastic specimens of cord's insulator or jacket.The tensile strength, elongation and hardness of dumbbell specimens before/after aging can be compared.This tester uses hot-air-circulation to make specimens age. Its interior is seal-ed well and it/s equipped with the induced draft device & auto shut-off protection if over-heated, inner air is changable. It can also be us-ed as a drying oven by introducing web-frame.

Please refer to the attached PDF for detialed information.


Aging Oven

Aging Oven

GT-7017


Insulator or coated specimen must be hung vertically on the test shelf, heated by specified temperature for a certain time, then take out and lay it in the room te-mperature over four hours. After that, compare the cross-sectional area before heated and mark line di-stance after heated to get its tensile strength, elon-gation rate, and residue rate.


Please refer to the attached pdf for detailed information.


Plug Static Pull Tester

Plug Static Pull Tester

GT-7165-p

This machine is suitable to test load strength between the conductors and blades. It can test six samples at the same time by a gradually applied pull of a certain load to the free end of the cord while the attachment plug is securely supported. The force shall be applied for a specified time in a direction perpendicular to the plane of cord entry.


Please refer to the attached pdf for detailed information.


Cord Ball Pressure Tester

Cord Ball Pressure Tester


GT-7304


This tester s used for measuring the heat-endurance and pressure resistance of sheathing of the cord. Testing method is to put the specimen upon a testing stand inside a constant temperature chamber which is predetermined at 125 2 C, and pressed with a ball end in diameter 5 mrn for one hour: afterwards take out specimen and put it into cool water for 10 seconds, then measure its depth of concavity. It will be qualified if the depth is within 2 mm.

Please refer to the attached PDF for detialed information.


Wate Bath

Wate Bath

GT-7039-m

Soak the specimen in warm water after a specified time, then observe whether there are degenerative conditions for the specimen such as blister, fading, swell, etc in its surface to judge its quality and also calculate the change rate of weight before / after test.

Please refer to the attached pdf for detialed information.


Molding Test Press

Molding Test Press


gt-7014-a

this machine is very convenient for preparing test specimens. Put raw materials into iron cie and clamp die between the electric heating plates of the machine, then heat and compress the die to mold the raw materials into specimens for testing in laboratory and being n:w standard in mass production.

please refer to the attached pdf for detialed information.


Cord Insulator Thickness Gauge

Cord Insulator Thickness Gauge


GT-313B

Tis Gauge is specially designed to measure cord insulator' s thickness. It is a table type and its meter is pegged on base. Therefore, you don't need to pick it up by hands. Needle-type clamp can accurately measure cord insulator' s thickness and even measure the deformed or tubular specimen.

Please refer to the attached PDF for detialed information.





 
 
 

Indiamart

Terms of Use - Privacy Policy - Link to Us

Copyright © 1996-2014 IndiaMART InterMESH Ltd. All rights reserved.