Toggle Type Clamping
clamping force: 75 Tons to 250 Tons 

Standard Features

• 5 Point Double Toggle with Auto-Lubrication.
• "T" Slotted mould platens for mould mounting.
• Fully Automatic Mould height adjustment with tonnage setting.
• Three stage low-pressure Mould safety.
• Low pressure mould open safety for stripper and split safety.
• Multi stroke ejector.
• Barrier type screw suitable for all engineering polymers and polylefin's.
• Right angle check ring assembly for better volumetric stroe control.
• Compact duel cylinder injection unit.
• 5 Stage velocity control and 5 stage hold on pressure control.
• Hydraulic and Electrically operated safety guard.
• Programmable Air jet for punch nd cavity.
• Tritek make PLC controller.
• Linear potentiometers for clamping, injection and ejector.
• Rotary encoder for mould height adjustment.
• Pressure transmitter for pressure dependent injection change over from fill to pack.

82 Grams to 1100 grams Shot Capacity

Hydromechanical Type : 80 Tons to 350 Tons
Clamping Force: Hydro- Mechanical Concept

Hydro Mechanical type Clamping system where small cylinders employed to travel the mould platen at high speed. At the end of mould closed clamp unit is blocked mechanically and then high pressure tonnage cylinders is subsequently pressurized to apply locking tonnage uniformity to the mould.

Features of Clamping Unit :-

• Platnes with "T" slot for mould fitting.
• Motorised Mould height adjustment (TP-150 onwards)
• Large space between Tie Bars to Accommodate large moulds.
• Low pressure mould safety
• Stroke control of moving platen by encoders
• Tonnage setting direct from MMI
  

Features of Injection Units :-

• Nitrided Screw - Barrel
• Direct Screw drive by high Torque hydro Motor
• Compact dual Injection Cylinder design
• Suck Back - before refill and after refill
• Screw stroke monitor by encoders.
• Five stage velocity control and five stage hold on pressure control.
• Nitrogen accumulator for high speed injection (optional).

Standard plastic injection machine is of the latest stle, which has introduced in the newest technology and adopted the idea of advanced modularization design. It uses the high response proportional varaiable pumps and the injection and mold lock differential control.

With strong drive system, advantaged technical parameters, and whole machine performance, it has greatly enhanced its performance to price ratio. It can also use the semi closed loop control system to achieve good stability, fast speed and fine precision and high response. It is applicable to plastic products with high precision requirements. Hydro Mechanical type clamping system where small cylinders employed to travel the mould platten at high speed. At the end of mould closed clamp unit is blocked mechanically and then high pressure tonnage cylinders is subsequently pressurized to apply locking tonnage uniformly to the mould.

Features of Clamping Unit:

• Platens with "T" slot for mould fitting.
  
• Motorised mould height adjustment (TP-150 onwards).
  
• Large space between Tie bars to accommodate large moulds.
  
• Low pressure mould safety.
  
• Stroke control of moving platen by encoders.
  
• Tonnage setting direct from MMI. 

Features of Injection Unit:

• Nitrided screw- barrel
  
• Direct screw drive by high Torque Hydro motor.
  
• Compact dual injection cylinder design.
  
• Suck Back - Before refill and after refill.
  
• Screw stroke monitor by encoders.
  
• Five stage velocity control and five stage hold on pressure control
  
• Nitrogen accumulator for high speed injection (optional)

Our range of Plastics Injection Moulding Machines have a three colour marble effect injection 

Specifications:

• Cabinet - type holder integrates the mold plate
• Pressure and flow whole - proportion running
• High - performance, low - noise oil pump
• High - precision position transducer
• Digital memory for mold group 
  

MPFC-PLUS machines monitor melt pressure through the use of melt pressure transducer fitted on the nozzle tip.

Specifications	Units	MPFC-80	MPFC-100	MPFC-150	MPFC-200
Clamping Unit
Clamping Force	Tons	80	100	150	200
Mould Opening Strike	MM	310	350	400	450
Distance Between tie-bars	MM	325*325	355*355	400*400	450*450
Mould Platen Size	MM	500*500	550*550	600*600	690*690
Max. Daylight	MM	620	700	850	950
Min. Mould Height	MM	175	200	250	250
Max.Mould Height	MM	310	350	450	500
Ejector Stroke	MM	60	60	80	80
Ejector Force	Tons	2.6	4	5	5
Injection Unit
Screw Diameter	MM	30 35	35 40	40 45	45 50
Screw L/D Ratio		22:01	22:01	22:01	22:01
Injection Pressure	Kg/cm2	2340	1750	2000	1715
Max. Swept Volume	CC	92	125	125	163
Rate of Injection	Cc/sec	66	90	72	93
Max. Screw Speed	RPM	10-240	10-300	10-300	10-300