Anupam Enterprises

Anu-Min wood coating is a two-component, fast curing, high solids, melamine natural wood finish specially formulated to protect furniture and other wooden surfaces whilst enhancing its natural appearance.

Monocoat is a two-component, durable, high solid, high build, aliphatic acrylic polyurethane coating that combines superb corrosion and chemical resistance with the attractiveness of high gloss coatings. It can withstand primer application. It is available in both glossy and matt versions. Metallic colours are also available.

Monocoat is a two-component, durable, high solid, high build, aliphatic acrylic polyurethane coating that combines superb corrosion and chemical resistance with the attractiveness of high gloss coatings. It can withstand primer application. It is available in both glossy and matt versions. Metallic colours are also available.

Anuthane Enamel is air drying two-component, extremely durable, high solid, aliphatic acrylic polyurethane coating with superior gloss and colour retention when subjected to prolonged and severe atmospheric conditions. It is available in matt finish also.

Anuthane Enamel is air drying two-component, extremely durable, high solid, aliphatic acrylic polyurethane coating with superior gloss and colour retention when subjected to prolonged and severe atmospheric conditions. It is available in matt finish also.

A premium range of high quality, two component acid curing lacquers, for use where high durability is desired. Anu-Min products have good pot life and fast cure characteristics and are suitable for a wide range of applications, including contract and domestic use. It is recommended for interior application only.

Anuchlor 555 LB is a high performance coating based on plasticized chlorinated rubber and suitably pigmented for heavy-duty protection in severe moisture and chemical laden environments.

Anuchlor - MIO is a high performance high build chlorinated rubber based coating pigmented with micaceous iron oxide (MIO) pigment. MIO is a lamellar plate-like pigment that forms a thick lustrous layer after application. As the coating dries, the very thin platelet shaped pigment particles orient themselves parallel to the substrate to give an armoured effect to the film and also act as an impediment to the diffusion of oxygen and moisture through the film. It is ideal for use in marine and chemical environments.

Anuchlor - MIO is a high performance high build chlorinated rubber based coating pigmented with micaceous iron oxide (MIO) pigment. MIO is a lamellar plate-like pigment that forms a thick lustrous layer after application. As the coating dries, the very thin platelet shaped pigment particles orient themselves parallel to the substrate to give an armoured effect to the film and also act as an impediment to the diffusion of oxygen and moisture through the film. It is ideal for use in marine and chemical environments.

Coroguard SBP - 100 is high solids, high build polyamide cured coal tar epoxy coating. The outstanding water resistance of coal tar, together with the chemical and solvent resistance, toughness and adhesion of epoxy resin, combine to give excellent overall corrosion protection.

Durapoxy 200 is a two-component high solid epoxy coating formulated for demanding marine and chemical environments. The cured coating offers excellent adhesion to metals, wood, concrete etc. and combine hardness with good flexibility. Either clear or pigmented, the coating presents a high gloss appearance and exhibits excellent resistance to fumes, spillage and splash of acids, alkalis, solvents, chemicals, jet fuel, grease etc.

Anumastic - 102 is two-component high solid high build epoxy mastic maintenance coating. This self-priming coating exhibits superior adhesion to bare, lightly rusted or previously painted steel. This flexible coating has exceptional combination of corrosion, abrasion, chemical and impact resistance, plus impermeability to gases and vapours not possessed by any other coating.

Duracoat - 6000 is a two-component high solid epoxy coating designed to provide excellent protection in demanding environments and is especially suited as a tank coating in petroleum products industry.

Anticora - MIO is a two-component high build epoxy coating ideally suited for exterior application. It is highly tough and abrasion resistant and has increased weather resistance. Anticora - MIO is pigmented with micaceous iron oxide (MIO), a lamellar plate-like pigment that forms a thick lustrous layer after application. As the coating dries, the very thin platelet shaped pigment particles orient themselves parallel to the substrate to give an armoured effect to the film and also act as an impediment to the diffusion of oxygen and moisture through the film.

Chemoguard coating system is amine cured, 100% solids, two-component high build, heavy-duty epoxy protective coating designed to combat corrosion, erosion, abrasion, chemical attacks, temperature extremes and other destructive conditions.

Anticora EZC 500 is a two-component epoxy polyamide anticorrosive high performance primer containing zinc chrome as rust inhibitive pigment. It cures to a tough and highly rust preventive coat.

Blastprime EZP 200 is a fast drying, abrasion resistant blast primer suitable for application in the workshop to fabricated steel units. It is designed for thin-film application to provide short-term (typically 6 months) protection to structural steel prior to or after fabrication. It may be cut and welded through.

Anticora EZP 500 is a two-component high solid primer with lead free rust inhibitive pigmentation.

Anuzinc 235 EP is an epoxy resin based high performance coating formulated for extreme marine and industrial environments and is highly suitable for priming iron and steel surfaces or touching up damaged zinc coatings on galvanized or zinc sprayed surfaces.

Anuchlor CZP 500 is a high performance high build primer for structural steel surfaces based on plasticised chlorinated rubber and pigmented with zinc phosphate rust inhibiting pigment. It can be applied on manually cleaned steel surfaces where blast cleaning is either impractical or cost-restrictive. It can be overcoated with conventional and chlorinated rubber topcoats.

Anuzinc 2001 TP is a solvent based, high solids, self-curing, inorganic ethyl silicate, two-component zinc rich coating containing 83% by weight of zinc in the dry film.

Wud-Fil wood filler has been designed to offer wood coating professionals an easy to use solvent based wood filler that can be applied on most variety of wooden surfaces and is very fast curing. It prepares a smooth surface for staining or finishing. It is recommended to be used on open grain timber, veneer etc. for interior / exterior furniture. No sanding is required and the excess filler can be easily wiped off the surface with a clean fabric.