Deluxe Metal Processing Chemicals Pvt. Ltd.

Meproche HRC is a specially designed synthetic cement to withstand abrasion and high temperatures (upto 1800ºC). Rhis heat resistant coating consists of two components viz. powder and syrup.It is an air-curing system.It can be plastered or casted as per requirement in situ. The casted component has high compressive strength too.
 
Method Of Use :
Take 1 part syrup and to it add powder slowly along with stirring. Powder may be taken from 0.8 parts to 1.2 parts depending on consistency required. The mortar can now be casted on the surface required to be protected from heat.
 
Shelf Life :
After mixing it be used within 20-25 minutes as the pot life is low. However the shelf life of individual components is very high and can safely be taken as one year.
 
Curing Time :
After casting allow the mortar to air-cure for about 10-12 hours, after which the surface is ready for use.

Meproche AAR 405 is a specially designed adduct of phenolic and epoxy resin cement to withstand alkaline materials and mild acids.It has strong adhesion and high compressive strength of app. 40000 psi.Its a low shrinkage type cement and can stand temperatures upto 150° C. The product consists of three components which have to be used in proper portions as per direction given below:

Method Of Use :

Surface preparation :
The surface to be coated should be free from dirt, oil, grease and rust. If needed grinding, sand paper or shot or sand blasting should be done.

Preparation of mortar :
Take 20%(of total mortar by weight) of syrup and to it add 14% (of mortar weight) of catalyst .Stir well for few minutes. Add powder to the extent of 66% (Of total mortar weight).Now the mortar is ready for use. Apply on the surfaces to be coated(which were cleaned earlier).

Shelf Life :
After mixing it is to be used within 20-25 minutes as the pot life is low. However the shelf life of individual components without mixing, is very high and can safely be taken as one year.

Curing Time :
After casting allow the mortar to air-cure for about 10-12 hours, after which the surface is ready for use.

Meproche AAR 410 is a specially designed synthetic cement to withstand alkaline materials and mild acids.It has strong adhesion and high compressive strength of app. 50000 psi.Its a low shrinkage type cement and can stand temperatures upto 110 C.
The product consists of three components which have to be used in proper portions as per direction given below;

Method Of Use :
Surface preparation :
The surface to be coated should be free from dirt,oil,grease, and rust.If needed grinding,sand paper or shot/sand blasting should be done.

Preparation of mortar :
Take 30% (of total mortar by weight) of syrup and to it add 3% (of mortar weight) of catalyst .Stir well for few minutes. Add powder to the extent of 67% (Of total mortar weight).Now the mortar is ready for use. Apply on the surfaces to be coated (which were cleaned earlier).

With the support of competent professionals, we formulate international standard gold shining chemicals, also known as gold shining salt. Eproche GS is a formulated compound and is used for electropolishing and deplating of gold and its alloys containing nickel, copper and zinc. The electrostripping or electropolishing is done by readjusting gold molecules on the top surface by action of chemicals by using a machine of nominal cost for supplying 10 to 30 volts DC. along with timers ammeter and voltmeter.

Method Of Use Of Gold Shining Chemicals:

• Dissolve 10 % of Meproche GS Salt in tap water and put it in the bucket of the machine or in a beaker as the case may be.
• The copper/ s. s. hooks of ( ) anode should be attached to the items to be stripped, and cathode (-) can be stainless steel or titanium.
• The bath so prepared should be heated upto 50 to 60ºC. and should be kept at that temperature
  Now pass the DC current for 10/15 seconds of a voltage of 20 / 25V. Remove the articles from anode, rinse and dry - the polishing is complete
• A small amount of agitation is preferred

Working conditions

• T =50/60 degree C
• t  =10 to 15 sec
• V = 20/25 Volts

With the support of modern manufacturing facility, we are able to develop eco-friendly meproche specialty products. The meproche specialty products are featured with purity, accurate composition and hence are globally accepted by our clients. It finds application in various industries including engineering, auto and steel.

Different kinds of meproche specialty products offered by us include following:

Meproche 401 Rust Removers

Meproche 401 rust removers is a slightly acidic liquid. It is applied on the rusty surface and is left for 2 to 5 minutes and then wipe out the rust.

Meproche C-21

A two pack type rust convertor obtained by mixing two components Meproche 401 and Meproche C-21 in a ratio of 4:1. It is apply on the rusted surface for four to five hours. By using wire brush, remove the loose scales on the surface. In case of highly pitted surfaces, the operation can be repeated if needed. It converts the rust into protective film.

Based on polyhydroxy organic compounds, Meproche 21 (Rust Converter) is used to remove old rusty pitted steel surfaces. It converts the most adherent surface into a protective coating. In addition, it also removes surface rust from newly manufactured steel sections. It is supplied in two pack system.

Method of its application:

Mix 50 gms of part Meproche 401 rust removers to 1 kg. of Meproche C-21

• Apply it on the rusted surface
• Leave it for 4 to 6 Hrs
• Remove rust by wire brush
• Repeat the process if necessary

It efficiently converts the balance rust into a passive state to prevent further rusting. It provides a temporary rust-prevention. It can be subsequently painted or lined. There is no need of wire brush operations in case of newly manufactured steel with a very thin rusty surface. Meproche 21 Rust Converter is mildly acidic in nature hence use rubber or polythene while handling it.

We are one of the trustworthy organizations for offering wide range of quality paint removers. These paint removers are developed using quality raw materials under the surveillance of the experienced chemists. Meproche paint removers are formulated as per ISS 430 & 431.

Various paint removers offered by us include:

Meproche Paint stripper:

It is a formulated product and is used to remove paint from steel and other substrates. Wide range of paint stripper is offered in various grades depending on the type of paint to be removed. In addition, it also depends on the position of the surface i.e. vertical or horizontal.

Meproche Paint Remover GP:

Meproche Paint Remover GP is a general purpose paint remover. It is widely used in various applications such as synthetic enamels, epoxies, stoving paints and powder paints. However the exact specifications of the substrate and paint should be given for much efficient removal.

Method of application:

By using either brush or dip method, Meproche Paint Remover GP can be applied. The surface after application should be left for five to fifteen minutes. By using a scraper or a wiper cloth, the paint thereafter can be removed. A second treatment can be given in case the paint surface is not removed completely due to human error of application.