Deluxe Metal Processing Chemicals Pvt. Ltd.

With our industrial experience of 26 years, we have emerged as one of the prominent manufacturers of heat treatment salts & chemicals. These chemicals are available to our clients in various packing as per their requirements. Featured with accurate composition, purity, non-toxic, the heat treatment salts & chemicals is widely catered to meet the requirements of engineering, steel and automobile industries. We make available preheating salts and neutral hardening salts,carburizing salts  Meproche regenerator and Meproche Economiser. The Meproche regenerator is used to keep the salt bath clean. Meproche Economiser prevents heat loss caused due to radiation and thus maintains the bath temperature . It reduces energy consumption and power cost.

Meproche MN 660 SPL

Specifications include following:

• Working range 660° C to 930° C,used with economiser
• Does not allow the formation of oxide film on the jobs
• Compatible with cyanide and allows easier absorption of carbon
• It is a preheating salt,used prior to baths of higher temperature ,above 1000 C

Meproche MH 830

• Meproche MH 830 works efficiently in the temperature range 830° C to 1100° C. It has applications in following:
• Harden 2% carbon, corrosion resisting steels, 12% chromium tool steels and steels used for cutlery
• Alternative to Meproche 970 or 1100 for hot working steels. For it, use of regenerator is recommended.

Meproche Acticator
Its working range is 640° C to 950° C.Its is used to activate  and enable easy absorption of cyanide.It is used for low carbon steel,if used with cyanide,else directly used for medium carbon and high carbon steels.

Meproche MH 970

Our Meproche MH 970 works in the temperature range 970° C to 1350° C. It finds application to heat the high speed and hot working steels for obtaining the desired hardening temperature in the above working range. The heat treatment salt avoids decarburisation and scaling of the steels. Some kinds of the steel show decarburisation during hardening with MH 970. It results into a low surface hardness. In this case, MH 971 is recommended to avoid any decarburisation.

Meproche MH 971

Specifications of Meproche MH 971 include following:

• Working range 970° C to 1350° C
• Used to harden high speed steel and hot working steels with minimum amount of decarburisation

Meproche MH 1100

Meproche MH 1100 is the most superior quality salt with high purity and contains no moisture. It finds application with regenerator to clean the high salt bath. Deoxidizing agent is present in the regenerator reacting and converting the oxide impurities into slag to prevent decarburisation. Meproche MH 1100 works in the temperature range 950° C to 1350° C.
Meproche N475
Its a nitriding steel.Works at 570 degree C.It is used for finished components.It doesnot distort the job.The case depth is low.For higher case depth air diffusion in the bath has to be incorporated.
CARBURIZING PRODUCTS 
Meproche Ready carb H
Highly activates cyanide type salt.Working range is 760° to 950° C.It cotains minm.50% sod.cyanide.It is used with economiser.Used for carburizing low carbon steels.
Meproche S-55
Working range 760° to 950° C Uses different type of activation.Case Depth upto 2mm is chievable.Used with economiser.
Meproche C 513
Its a carburizing Fluid.Drip feed type.Used for low carbon steel and mild steels.It has cheaper operating salt.No soot formation.Operating temp.950°C
Meproche MA
Its a carburizing fluid used in oxygen prode type furnace.Its a replacement for acetone.Gives same atmosphere and result.

Our company is offering quality Meproche C-21 rust convertor, that is based on polyhydroxy organic compounds. It is efficiently used to remove rust from stored steel and old rusted steel already erected (whether in RCC or otherwise). With the chemical Meproche C-21 rust convertor, pitted surfaces can be converted into a protective coat. It is supplied in two packs.

A surface treated with MEPROCHE C 21 accepts primers and paint fast. It increases adherence of primers and paints and thus improves the life of paints. It covers approximately 70/75 square meter per Kg.

Method of application:

• Mix 50 gms of part A to 0.950 kg. of part B
• Apply on the rusted surface and leave it for 4 to 6 Hrs
• Remove rust by wire brush
• Repeat the process if necessary

The chemical converts the balance rust into a passive state thus stop further rusting. It provides temporary solution for rust prevention. It can later be painted or lined. Rubber gloves should be used while handling Meproche rust convertor as it is mildly acidic in nature.

Note:

The information provided is based on our experience and tests conducted by us on typical specimen. However, the actual working conditions are beyond our control and knowledge. Hence, we are not responsible for any liability for loss, damage, injury or mishap resulted.

We are engaged in formulating and producing wide range of quenching, marqueching & tempering salts & oils as per the ISO standard. These tempering salts & oils are produced from using quality raw material in conformity with ISO standard. Following are various types of quenching, marqueching & tempering salts & oils offered by us:

Meproche Quenching Oil

It is a mineral oil based and is featured with high oxidation stability and low viscosity. The compounded mineral quenching oils provides good proportion of toughness and hardness and offer least warpage with standard steels. Cited below are types of Meproche quenching oils:

Meproche Fast Quenching Oil

Specifications and features of Meproche Fast Quenching Oil are mentioned below:

• Appearance Slightly pale
• Flash Point 195°C. Min
• Moisture Less than 0.1%
• Acidity (Organic & Inorganic) Less than 0.01% each
• Ash 0.05% max
• Pour Point Below 5
• Sap Value 0.2 to 0.5
• Specific Gravity 0.85 to 0.86
• Thermal Conductivity 0.087 to 0.09 BTU/HR/FT °F
• Viscosity 35 sec at RT by Ford cup no.4

Meproche Quenching Oil No.2

We offer meproche Quenching oil No.2 with following specifications:

• Appearance Slightly pale
• Moisture Less than 0.1%
• Acidity (Organic & Inorganic) Less than 0.05% each
• Pour Point Below 5°C
• Sap Value 1 to 8
• Flash Point 220°C. Min
• Ash 0.05% max
• Specific Gravity 0.892
• Thermal Conductivity 0.084 BTU/HR/FT °F
• Viscosity approx. 80 SUS at 40'C

Meproche Quenching Oil No.3

Cited below are the specifications of Meproche Quenching Oil No.3:

• Appearance Slightly pale
• Flash Point 180°C. Min
• Ash 0.1% max
• Pour Point Below 5°C
• Sap Value 4 to 8
• Moisture Less than 0.1%
• Acidity (Organic & Inorganic) Less than 0.05% each
• Specific Gravity 0.892
• Thermal Conductivity 0.084 BTU/HR/FT °F
• Viscosity approx. 80 SUS at 40'C

Meproche Martempering Oil

Meproche Martempering Oil has work stability in the temperature range 150° C to 280° C. It gives low viscosity jobs from case carburising by cyanides can directly be quenched in this oil. After quenching, the oil avoids use of temporary rust preventives.