Dolphin Floats Private Limited

Our combination of Multifilament Straight Fibres + Fibrillated Mesh Fibres "Nokrack" is 100% Virgin high tenacity polypropylene additive for water retaining structures. It is available in multiples of 10 mm & 20 mm to give 3D micro-reinforcement. This is to be used as micro reinforcement at minimum of 0.9 kg/m3 of concrete. Nokrack complies with ASTM C 1116 and ACI committee report 544-1R.

The key actions of Nokrack are as follows:

• Increases water proofing ability of concrete (reduces permeability).
• Reduces need to do water proof plaster, pressure grouting.
• Reduces shrinkage and plastic cracking in concrete.
• Makes the concrete dense & strong.
• Protects steel.

Areas of application:

• Roof slabs, wet slabs, toilet floor slabs, bathrooms, utility areas & kitchens.
• Water retaining structures.
• Effluent or sewage treatment tanks.
• Gunite & shotcrete.
• Ferrocrete tanks.
• Warehouse flooring.
• Rafts.
• Basement waterproofing.
• Overlays / toppings.
• Concrete Tanks

Properties:

• Length : Multiples of 10/20 mm.
• Construction : Combination of straight + fibrillated mesh fibre.
• Melting Point : 165 Deg C.
• Absorption : Nil.
• Acid Resistance : High.
• Alkali Resistance : Completely resistant.
• Salt Resistance : High.
• Thermal Conductivity : Low.
• Electrical Conductivity : Low.
• Tenacity : 6.5 GPD.
• Elongation : 19%

Important information for our buyers:

• Dosage: Minimum 0.9 kg /m3 of concrete or @ 125 g /50 kg bag of cement.
• Water Cement Ratio : NOKRACK is a physical micro-reinforcement and does not react chemically hence additional water is not required.
• Mixing Process: Mix directly in the concrete mixer @ 125 g /50 kg bag of cement or 0.9 kg/m3
• Note: Fibres should not be used for replacement of structural or load bearing reinforcement.

Product Code:

NOKRACK

STRONGCRETE is 100% Virgin high tenacity fibrillated polypropylene mesh fibre and is available in graded lengths. It provides 3D micro-reinforcement to concretes. It is used @ 0.9 kg per m3 of concrete (minimum). STRONGCRETE complies with ASTM C 1116 and ACI committee report 544-1R.

The key actions of STRONGCRETE are as follows:

• Reinforcement against shrinkage and intrinsic cracking.
• Replaces welded wire mesh / secondary crack control steel used for crack prevention of concrete floorings.
• Reduces bleeding and dust formation in concrete.
• Improves impact resistance 3-4 times.
• Improves abrasion resistance by 30-40%.
• Gives residual strength to concrete thereby helping reduce sudden failures. This is a desirable characteristic of concrete in areas prone to earthquakes.
• Reduces permeability, thus reducing water ingress and protects reinforcement steel from corrosion.
• Makes the concrete more durable & tougher.

Areas of Application:

• Industrial Flooring.
• Warehouse Flooring.
• Concrete Roads.
• RCC Beams, Columns & Slabs.
• Bridge Decks.
• Driveways.
• Overlays Toppings.
• Concrete Tanks.
• Basement Waterproofing.

All types of concrete, where toughness is required along with elimination of shrinkage cracks and other desirable characteristics as mentioned above.

Properties:

• Length : Graded
• Construction : Fibrillated
• Melting Point : 165 Deg C
• Absorption : Nil
• Acid Resistance : High
• Alkali Resistance : Full
• Salt Resistance : High
• Thermal Conductivity : Low
• Electrical Conductivity : Low
• Tenacity : 5.5 GPD
• Elongation : 15%

Important information for our buyers:

• Dosage: Minimum 0.9 kg /m3 of concrete.
• Water Cement Ratio : STRONGCRETE is a physical micro-reinforcement and does not react chemically hence additional water is not required.
• Mixing Process: Mix directly in the concrete mixer @ 125 g /50 kg bag of cement or 0.9 kg/m3.
• Note: Fibres should not be used for replacement of structural or load bearing reinforcement.

Product Code:

STRONGCRETE

STRONGPLAST is 100% Virgin high tenacity polypropylene straight fibres in graded lengths. It provides 3-D micro-reinforcement to plasters as well as concretes. These are available in multiples of 3 mm, 5 mm and 6 mm. This product is used @ 0.9 kg /m3 of plaster or concrete (minimum). STRONGPLAST complies with ASTM C 1116 and ACI committee report 544-1R.

The key actions of STRONGPLAST are as follows:

• Provides inherence micro-reinforcement against shrinkage and intrinsic cracking.
• Reduces rebound losses in plasters to 60-70%.
• Reduces bleeding and dust formation in concrete.
• Improves impact resistance 3-4 times.
• Improves abrasion resistance by 30-40%.
• Gives residual strength to concrete thereby helping reduce sudden failures. This is a desirable characteristic of concrete in areas prone to earthquakes.
• Reduces permeability and thus protects interior paint in plasters.
• Reduction in permeability also helps protect reinforcement steel in concrete applications.
• Makes the concrete more durable.
• Makes hardened concrete more tough.
• Improves speed and finishing of plasters.

Areas of application:

• Internal and external plasters.
• Industrial flooring.
• Warehouse flooring.
• Concrete Roads.
• RCC Beams, Columns & Slabs.
• Bridge decks.
• Driveways.
• Overlays / toppings.
• Concrete tanks.
• Precast elements.
• Shotcrete / guniting.
• Basement waterproofing.

All types of plasters, precast elements and concretes, where toughness is required along with elimination of shrinkage cracks, reduction in permeability (improved water resistance) and various other parameters mentioned above.

Properties:

• Length : Multiples of 3/5/6 mm.
• Construction : Straight.
• Melting Point : 165 Deg C.
• Absorption : Nil.
• Acid Resistance : High.
• Alkali Resistance : Completely resistant.
• Salt Resistance : High.
• Thermal Conductivity : Low.
• Electrical Conductivity : Low.
• Tenacity : 6.5 GPD.
• Elongation : 19%.

Important information for our buyers:

• Dosage for plasters : 100-125 g / 50 kg cement bag as recommended by designer.
• Dosage for concrete : Minimum 0.9 kg / m3 of concrete i.e. @125 g /50 kg bag of cement.
• Water Cement Ratio : STRONGPLAST is a physical micro-reinforcement and does not react chemically hence additional water is not required.
• Mixing process : Mix directly in the concrete mixer @ 125 g /50 kg bag of cement or 0.9 kg/m3.
• For plastering applications dry mix with sand cement mortar before adding water.
• Note : Fibres should not be used for replacement of structural or load bearing reinforcement.

Product Code:

STRONGPLAST