The Eclipse Combustion Veri-Flame single burner monitoring system controls the start-up sequence and monitors the flame of single gas, oil or combination gas/oil burners. There are three different models to the Veri-Flame Line:
- No purge
- Purge
- Modulation
Each model features field selectable trial for ignition (TFI). Each model is also available for use with four types of flame sensor:
The Eclipse Combustion Bi-Flame controls the start-up sequence and monitors the flame of two individual gas, oil or combination gas/oil burners. bi-Flame controls two flames as a single burner.
Standard features include:·
- UL recognized, FM approved and CSA certified
- Microcomputer based system
- 0-12 VDC flame signal test ports conveniently located on front of unit.
- Monitors up to two burners.
- Flame sensor module for ultraviolet and/or flame rod.
-· DIP switches for timing functions and system configuration.
- Internal safe-start diagnostic testing.
- Available with valve proving system sequence, proof of valve closure testing, history logging and other optional features.
The Eclipse Combustion Multi-Flame controls the start-up sequence and monitors the flame of up to 20 gas, oil or combination gas/oil burners connected to a common valve train.
Standard features include:
· UL recognized, FM approved and CSA certified · Microcomputer based system
· Plug-in to the motherboard modular design for the following parts:
o Power supply
o Relay module
o Logic Module Eclipse Peek-a-Flame sensor modules with 0-12 VDC signal test ports
· Monitors up to 20 burners with expansion board option.
· One down, all out logic.
· Flame sensor module for ultraviolet and/or flame rod.
· DIP switches for timing functions and system configuration.
· Internal safe-start diagnostic testing.
· Test mode for pilot flame adjustments.
· Available with valve proving system sequence, proof of valve closure testing, history logging and other optional features.
Eclipse butterfly valves are designed to control air and gas flow to all types of combustion systems. They should not be used as tight shut-off valves. Available in manual and automatic modes.
The eclipse rotary actuator is a keypad programmable, direct coupled, modulating motor for use in burner and valve control systems. It is typically used with and electronic control to regulate a process temperature. The drive shaft of the actuator connects to a butterfly valve stem, which rotates 90 degrees from minimum to maximum position.
Actuator features include
- Solid state electronics
- Three digit led display
- Membrane keys
- 4-10ma, 0-10vdc and switch inputs for positioning
- 2 auxiliary contacts for position feedback
Features
Type
keypad programmable direct coupled rotary actuator.
eclipse minimatic burner is a compact packaged gas burner designed for use in process air heating applications such as ovens and dryers. These burners have special applications in glass annealing lehr’s and have been successfully operating in many installations across the country. Minimatic burners feature an integral air and gas butterfly mounted on the same shaft for ease of set-up and dependable operation.
Eclipse solid state uv scanner consists of a phot-diode and electronic network. The photo diode and electronics are sealed in an aluminum hosing, providing protection against dust, oil and water. This uv scanner is used to sense infrared through ultraviolet light and responds to the flicker on gas and oil flames. This device will not produce a flame signal if any internal components fails. It can be used on burner system that continuously operate longer than twenty four hours.
Eclipse immersopak (ip version 2) burners are easy to install, simple to operate and offer long service life in industrial environments. They are ideal for heating immersion tubes on cleaning tanks, spray washers, salt baths, quenching tanks, tempering tanks, asphalt tanks, and similar equipment. immersopaks are nozzle-mixing burners complete with packaged combustion air blower. They are available in four sizes for firing immersion tubes up to 12” in diameter. Capacities range from 300,000 to 2,200,000 btu/hr. depending on burner size, fuel and control method selected, turndown ratios as high as 56:1 can be achieved. Internal gas and air orifices are provided to ease burner setup. A wide variety of options and configurations are available due to the modular design of the burner.
Installation, retrofitting is easy because versatility and adaptability are designed into the immersopak, new or retrofit installations rarely require extensive tube or exhaust modifications.
- easy to install and operate. - high turndown. - built for long service life in industrial environments. - low maintenance. - low noise levels. - direct spark ignition. - multiple fuel capability.
115 / 120 volts 50 / 60 hz standard 220/50 or 240/60 available
Eclipse 200 LT valves are manually opening valves that automatically shut off the gas supply to a combustion system when any interlocking limit switch opens.
Series 200 LT Valves includes the visual indicators of open / close position a red flay visible on top of the valve
Eclipse Atmospheric Injectors are simple, low cost, adjustable mixers designed to provide an air gas mixture to one or more burners. Atmospheric Injectors use the kinetic energy of a stream of gas to entrain part or all of the air required for combustion.
Two series of injectors are available: “Low Pressure” for use with gases up to 28” w.c and “High Pressure”, for gases from 1 psig to 30 psig. Both are available as either” Single Stage” or “Compound” units depending on the type of gas used. Compound Injectors employ an additional sleeve which assists in entrainment for highest Btu gases.
gases: natural, manufactures, mixed liquefied petroleum or lp gas-air mixture.
mounting: upright only
note: all maxitrol regulators should be installed and operated in accordance with maxitrol’s “safety warning” bulletin.
both the rz and 210z series are adaptable for air-gas mixing applications. They may be used for outlet pressures close to atmospheric, from slightly above to slightly below (- 1. 0” to 1. 5” w. C. ; -2. 5 mbar to 3. 75 mbar).
because of balanced valve construction, z models offer superior performance at an economic price to other type atmospheric regulators.
convenient tap locations are provided on the 210z models, for downstream sensing. Cross connections and differential control. Four locations can be tapped and plugged for measuring pressure.
pipe sizes are consistent with standard models – 3/8” to 1” for the rz series and 1” to 4” for the 210z series. Metric threads are also available.
maxitrol z model regulators are used to flow control of burners, nozzle, mixing tees, and proportional premixers.
Eclipse Recilculating High Temperature (RHT) indirect air heating burners are designed to heat recirculating ovens and dryers where the products of combustion must be isolated from the process air stream. They are also excellent for use in industrial space heating systems. These burners feature an industry-proven burner, firing chamber and exhaust tubes assembled as a single unit for easy installation and optimum performance.
Separates products of combustion from process air stream.
Completely packages for easy installation.
Available as a side plate or duct unit.
Outlet temperatures to 2900C (5500F); 800C (1500F) maximum temperature rise per pass.
High efficiencies from 60% to 75%.
Low process air flow pressure drop.
Low NOx in external exhaust stream.
Meets NFPA 86 recommendations.
System options include valve trains, control panels and combustion air inlet filters.
High temperature limit protection and process air flow switch provided as standard.
Front access for easy maintenance.
Free-floating design allows for thermal expansion.
Eclipse ES-Series ratio regulators are used in applications where gas to air proportional flow is required. The gas flow is controlled as a function of the air pressure through a loading line which connects into the top of the regulator. As the system air pressure increases, it forces the ratio regulator valve to open causing the outlet pressure to increase until the two pressure balances. As the load line pressure increases, the ratio of the outlet pressure to the load line pressure will be slightly less than 1:1.
The ratio regulators have a bias adjustment for varying the gas flow when setting the burner at low fire. It can be used to increase or decrease the gas flow resulting in gas rich or lean combustion. The adjustment is restricted in the gas rich direction therefore limiting the gas flow at zero air pressure.
The ratio regulators are designed to optimize performance as ambient temperature and inlet pressure vary. Feature include:
UL recognized and CE approved for natural gas, propane & butane.
Valve seat design for consistent low fire repeatability.· Balanced double diaphragm design allows regulator to operate over a wide range of inlet pressures while minimally affecting outlet pressure.
Rugged die cast aluminum housing.· Corrosion resistant internal components.
Synthetic rubber diaphragms for excellent low temperature performance.
Inlet pressure tap with connector (1-1/2”, 2” & 3” NPT (Rp) models only.)
These are two way normally closed valve suitable for general air and gas flow control. Their normally closed direct acting design provides reliable, positive performance in gas fired applications.
Sizes: ¼” to 3” NPT
Continuous duty Class F insulation. Coils are available in volts AC/Hz for- 24/60, 120/60, 110/50, 240/60, 220/50, 480/60
Approval: UL listed; FM approved, AGA,CGA and CSA certified.Literature No: Bulletin 760-2,3,4.
The thermjet liquid burners are nozzle mix burners for light or heavy oil. The burners are designed to operate on low pressure atomizing air and will operate efficiently throughout a wide operating range. Typical applications include high temperature kilns and forge and melting furnaces.
The thermjet Liquid burners are available in three sizes with maximum capacities from 300,000 BTU/hr to 1,500,000 BTU/hr.
All burner models can be controlled on-ratio with a cross-connected fuel regulator to maximize efficiency, or with fixed air to improve temperature uniformity in the furnace.
The standard burner configuration includes an manual adjustable oil flow metering valve, The burner also includes an integrated air orifice to simplify piping, set –up and adjustment. The burner can also be supplied with an optional oil pressure gauge.
The combustion air, atomization air and oil inlets are independently adjustable in 900 increments to suits a variety of piping alternatives.
Burner ignition is done with a gas pilot. A manual torch can be used in some applications. The burner is supplied with a 3.4000F rated refractory combustor and cast iron holder to allow mounting to the furnace wall.
Ultimate Energy Systems Manufacturer and supplier of heating equipment such as water heater, hotel water heater, hot water heater, automatic water heater, fully automatic water heater, electric water heating system and industrial water heater.
Apt Controls And Appliances Private Limited Manufacturers and exporters of electric heaters, panel space heaters and panel space heater with connecting leads. Also manufacture water heater thermostat, rod type thermostat, bimetallic enclosure thermostats and commercial thermostat.
Processing...
