Electric Components & Spares

Type: EEC / FLP / TS - 2002
Our range of Flameproof Temperature Switches is used for controlling the hydraulic oil temperature in underground coal mining electro Hydraulic Machines. All stainless-steel enclosures.

Specifications:
• Switch Type: (SPST) break on rising temperature
• Contact Rating: AC resistive load 10 Amp at 250 VAC, DC resistive load 2 Amp at 28 VDC
• Thermostat temperature rating: 0-110°C
• Maximum working temperature: 110°C
• Maximum working pressure: 17.5Kg/cm (250 psi)

Certification:
• CMRI Approval No.: CMRI/TC/P/H711 DT 15th September,2002
• DGMS Approval: 362/1138/EHQ dated 21st May, 2004 & Mark no. – 513 of 2004
• BIS License No: CM/L-2291047 dt 30.01.95

Type: EPC - 1
Our range of Flameproof Pullcord Switches provides a safe and effective means of immediately stopping the conveyor, haulage & man riding system.

Specifications:
• Contact: 1 NO/1 NC or 2 NO/2 NC
• Rating: 550 V AC/10Amps
• Cable Entry: 2 Nos. FLP Mining Type or double compression cable glands

Certifications:
• CMRI Approval No.: CMRI/TC/S/H975 dt. 30.07.1999
• DGMS Approval: 207 of 1981, Renewed vide letter ref. 362/1031/EHQ dt. 24.08.01 & renewed vide letter ref. 362/1997/EHQ dt. 17.11.03
• BIS License No: CM/L-2291047 dt. 30.01.05

Type: Ex- 25
We offer 25 Shot Exploders that comes with dry / rechargeable NI - CD battery. It is a solid state capacitor discharge type exploder suitable for firing up to 25 shots in underground gassy coal mines/seams of Degree I & II.

Specifications:
• Capacity: 25 Shots
• Max. resistance in circuit: 150 ohms
• Firing Current: 1.5 Amps
• Duration of firing current: Less than 4 Millisecond.
• DC Voltage Output: 500-600
• Battery: 10.5 VDC Dry or 9.6 VDC Ni-Cd

Certification:
• CMRI Report No.: CMRI/TC/S/H754 dt,. 11.06.99
• DGMS Approval: 14(24)77-Genl/2206 dt. 21.06.2000, Approval Mark No.: SA-2/78
• BIS License No: CM/L-9242271 as per IS: 9836-1981

Range: -
• 100 or 200 shot. For industrial use also available.

Type: EEC/25A,PLUG & SOCKET/01
We ofer Indusrial Plugs And Sockets, these are welding receptacles in sheet metal, dust proof and damp proof enclosure,

Specifications:
• Range Voltage: - 20A, 240V, 1 Phase
• 63A, 440V, 3 Phases & N
• Fully Interlocked cover and plug .
So that it can not be opened with switch in ON position

Industrial Type (NFLP) Pull Cord Switches
Type - PCS 3
Our range of Industrial Type (NFLP) Pull Cord Switches provides a safe and effective means of immediately stopping the Conveyor & Haulage. These are available in cast iron/aluminum enclosure for industrial applications. All these switches are dust and moisture proof to IP-65.

Specifications:
• Contact: 1 NO/1 NC or 2 NO/2 NC
• Rating: 550v AC/10Amps • Cable Entry: 2 Nos. single compression cable glands ¾ inch, ET

INDUSTRIAL TYPE (NFLP) BELTSWAY SWITCHES
Type – BSS 3
The Beltsway Switch roller can be positioned near the belt as required to allow only a certain amount of sway. Beyond the sway, the switch will operate and cut off the supply. In cast iron enclosure and dust and moisture proof to IP 66.

Specifications:
• Contact: 1 NO/1 NC or 2 NO/2 NC
• Rating: 550v AC/10Amps
• Cable Entry: 2 Nos. single compression cable glands ¾ inch, ET

Type: EEC / NFLP / CP -3
We offer Mining Type NFLP Control Panels that are used for pre start warning alarms before starting of conveyors, haulage and man riding systems.

Description:
1. On pressing push button the power goes directly to the power supplies of all the Audio Visual Alarms connected in series. Therefore all the alarms will start working throughout the length of the conveyor and the flashing light will glow at the stipulated frequency. After 15-60 seconds (as the required case may be), the AVA will stop and no volt coil of the conveyor starter will be energized automatically to close the contractor and start the conveyor.
2. There is a provision for tripping the starter unit or preventing it from starting if the PCS /BSS & ZSS are activated along the length of conveyor.

Specifications:
• Incoming Voltage: 550/440/220/110 VAC
• Cable Entry: 6 Nos. Mining Type or double compression glands

Type: EEC / FLP / FS - 2002
Our range of Flameproof Float Switches is used for maintaining the liquid level in an underground coal mining electro hydraulic machine. All stainless steel enclosure.

Specifications:
• Reed Switch Type: S.P.D.T. Switch
• Wattage: 10W
• Voltage: 250VAC
• Current: 1 Amps

Certification:
• CMRI Report No.: CMRI/TC/P/H712 dt. 05/09/02
• DGMS Approval No.: 362/1145/EHQ dt. 21/05/04
• Mark No.: 514 of 2004
• BIS License No: CM/L -2291 047 dt. 30.01.95

Type: ZSS 1
The Flameproof Zero Speed Switches has been designed for the protection of belts in case there is slippage within10% of the normal speed.

Specifications:
• Contacts:1 NO/1 NC or 2 NO/ 2NC
• Rating: 550VAC,10 Amp
• Cable Entry: Two Nos. of FLP mining type or double compression cable glands.

Certification:
• CMRI Approval: CMRI/TC/P/H975 dt.30.07.99
• DGMS Approval: 207 of 1981
• BIS License No: CM/L-2291047 dt. 30.01.1995

Type: BSS - 1
The Beltsway Switch roller can be positioned near the belt as required to allow only a certain amount of sway. Beyond this sway the switch will operate. The switch opens and cuts off the supply. This switch is used as a limit switch or foot pedal & dead man switch.

Specifications:
• Contact: 1 NO/1 NC or 2 NO/2 NC
• Rating: 550v AC/10Amps
• Cable Entry: 2 Nos. FLP Mining Type or double compression cable glands

Certification:
• CMRI Approval No.: CMRI/TC/P/H975 dt 30.07.1999
• DGMS Approval: 207 of 1981, Permissible variation of PCS vide, DGMS letter no. 1322/EHQ dt., 21.08.2002
• BIS License No: CM/l-2291047 dt. 30.01.1995