GM Induction Heater GM10 (with or without Boost up Facility)
GM Induction Heaters are designed to heat the Bearings and other shrink-fit components prior to mounting, using latest technology intelligent microcontroller based electronic controls.
The life of Bearings and other torque transmitting steel components, which are shrunk-fit on shaft, may get cut short due to rough handling and faulty installation or mounting methods. This can be avoided by expanding them by induction heating for the purpose of mounting of the component.
GM Induction Heaters are available in different models for mounting, range of bearings having bore size from 10 mm and above. Fast, safe and economical heating of bearings is best features of GM Induction heaters.
GM Induction Heater - GM10 has medium capacity to heat the components with intelligent micro controller based electronic controls. It can be easily carried to the site of operation, using specially designed handle provided on both sides. It can heat a bearing of 50 kg to 60 kg to temperature of 110oC with in 7 minutes.
GM Induction Heater - GM10 consists of the control mounted on main body of Induction Heater and a remote control is provided for higher efficiency.
GM Induction Heaters are designed to heat the Bearings and other shrink-fit components prior to mounting, using latest technology intelligent microcontroller based electronic controls.
The life of Bearings and other torque transmitting steel components, which are shrunk-fit on shaft, may get cut short due to rough handling and faulty installation or mounting methods. This can be avoided by expanding them by induction heating for the purpose of mounting of the component.
GM Induction Heaters are available in different models for mounting, range of bearings having bore size from 10 mm and above. Fast, safe and economical heating of bearings is best features of GM Induction heaters.
GM Induction Heater - GM 04 is light weight and portable for better performance. It has power capacity of 2 to 4.0 KVA. The controls are intelligent microcontroller based programmable electronic controls. It has two operating modes, Temperature mode and Time mode. Both are controlled through feather touch key Board. Both modes can be seen at the time of operation. It can also be used to heat bearings of larger diameter using a pair of Raiser Blocks size 55 x 55 x 130 mm. The unit can also be used to heat a plate of any magnetic material by placing the plate in place of the horizontal yoke across the vertical supports.
GM Induction Heater GM12 (Horizontal & Vertical with or without Boost up Facility)
GM Induction Heaters are designed to heat the Bearings and other shrink-fit components prior to mounting, using latest technology intelligent microcontroller based electronic controls.
The life of Bearings and other torque transmitting steel components, which are shrunk-fit on shaft, may get cut short due to rough handling and faulty installation or mounting methods. This can be avoided by expanding them by induction heating for the purpose of mounting of the component.
GM Induction Heaters are available in different models for mounting, range of bearings having bore size from 10 mm and above. Fast, safe and economical heating of bearings is best features of GM Induction heaters.
GM Induction Heater - GM12 has heavy capacity to heat the components with intelligent microcontroller based electronic control. It can heat a bearing of 60 kg to temperature of 110oC with in 7 minutes.
GM Induction Heater - GM12 Horizontal & Vertical Model is provided with manual or automated Roll-sliding Arrangement for the standard yoke 80x80x500 mm. The Roll-Sliding Arrangement is so designed that the yoke gets lifted mechanically or automatically rolls off from the vertical supports without rubbing or damaging and scraping mating surfaces. This arrangement provides additional safety, ease of operation and helps to improve productivity.
GM Induction Heater GM25 (Horizontal & Vertical with or without Boost up Facility)
GM Induction Heaters are designed to heat the Bearings and other shrink-fit components prior to mounting, using latest technology intelligent microcontroller based electronic controls.
The life of Bearings and other torque transmitting steel components, which are shrunk-fit on shaft, may get cut short due to rough handling and faulty installation or mounting methods. This can be avoided by expanding them by induction heating for the purpose of mounting of the component.
GM Induction Heaters are available in different models for mounting, range of bearings having bore size from 10 mm and above. Fast, safe and economical heating of bearings is best features of GM Induction heaters.
GM Induction Heater - GM 25 has heavy capacity to heat the components. It has intelligent microcontroller based electronic control.
It weights about 300kg. It can heat a bearing of 500kg to temperature as per requirement in customized time.
GM Induction Heater - GM 25 is provided with manual or automated Roll-sliding Arrangement for the standard yoke. The Roll-Sliding Arrangement is so designed that the yoke gets lifted mechanically or automatically rolls off from the vertical supports without rubbing or damaging and scraping mating surfaces. This arrangement provides additional safety, ease of operation and helps to improve productivity.
GM Induction Heaters are designed to heat the Bearings and other shrink-fit components prior to mounting, using latest technology intelligent microcontroller based electronic controls.
The life of Bearings and other torque transmitting steel components, which are shrunk-fit on shaft, may get cut short due to rough handling and faulty installation or mounting methods. This can be avoided by expanding them by induction heating for the purpose of mounting of the component.
GM Induction Heaters are available in different models for mounting, range of bearings having bore size from 10 mm and above. Fast, safe and economical heating of bearings is best features of GM Induction heaters.
GM Induction Heater - GM 50 has very heavy capacity to heat the components. It has intelligent microcontroller based electronic control.
It weights about 500kg. It can heat a bearing of 1000 kg to temperature as per requirement in customized time.
GM Induction Heater - GM 50 is provided with manual or automated Roll-sliding Arrangement for the standard yoke. The Roll-Sliding Arrangement is so designed that the yoke gets lifted mechanically or automatically rolls off from the vertical supports without rubbing or damaging and scraping mating surfaces. This arrangement provides additional safety, ease of operation and helps to improve productivity.
GM Induction Heater GM100 ( Tyre Induction Heater )
GM Induction Heaters are designed to heat the Bearings and other shrink-fit components prior to mounting, using latest technology intelligent microcontroller based electronic controls.
The life of Bearings and other torque transmitting steel components, which are shrunk-fit on shaft, may get cut short due to rough handling and faulty installation or mounting methods. This can be avoided by expanding them by induction heating for the purpose of mounting of the component.
GM Induction Heater / Tyre Induction Heaters - GM 100 has highest capacity to heat the components. It has controls similar to GM-series, which are intelligent microcontroller based electronic controls with data logger which can upload the all data month wise.
It weights about 3 Ton and capable to heat the Railway Wheel Tyre within 15 to 20 min.
GM Induction Heater / Tyre Induction Heater - GM 100 is provided with automated Roll-sliding Arrangement for horizontal yoke and operated automatically and manually in case of power failure. The automated Roll-Sliding Arrangement is so designed that the yoke gets lifted automatically rolls off from the vertical supports without rubbing or damaging and scraping mating surfaces. This arrangement provides additional safety, ease of operation and helps to improve productivity.
gm induction heater gmir50 (mounting & dismounting of inner races of cylindrical roller bearing)
gm induction heater - gmir 50 is specially designed for mounting and dismounting the inner races of cylindrical roller bearings used on the axles of railway rolling stock and in traction motors using latest technology intelligent microcontroller based electronic controls. It can be used in others industries with similar application.
gm induction heater - gmir 50 are safe, fast and economical heating of inner races of cylindrical roller bearings.
when a component is heated with the induction coil it acquires magnetism strong enough to attract iron particles, iron dust etc. To deal with this phenomenon, it is necessary to eliminate the residual magnetism after heating. The designs of the control panel of gm induction heater gmir 50 permits fast demagnetization by use of the heating coil itself. The induction coil can be used for demagnetization as well as heating.
principle
when alternating current flows through a coil wound around a component; it creates an oscillating magnetic field, which includes current in the component. The magnetic field takes the path of least resistance and also due to the skin effect; the outer periphery of the component gets heated more rapidly than the core.
based on the above principle, a ring shrunk fitted on the shaft will get heated more rapidly causing a temperature differential between the two. The difference in the temperature will cause the ring to expand to a stage where it overcomes interference and can be dismounted easily.
features
•
induction heating is more safe, reliable & clean process.
•
even unskilled labor can be trained to operate the equipment easily.
•
high heating rates can be easily achieved.
•
precise temperature and time controls are achieved through state of the art technology used in heaters.
•
lower cost & high efficiency are the plus points of induction heating.
gm motorized bearing extractor gm bem 30 is being developed in a unique concept as mobile work station (motorized high pressure extractor) to dismount direct mounted roller bearings (bearing no. 22320, 22326, 22328, 22330 )without damage or scoring to the component bore or shaft seating, with minimal force.
features & accesories
•
portable & assembled on 3 / 4 wheel trolley.
•
hydraulic power pack (max. Working pressure 750bars)
•
pressure releasing valve.
•
pressure safety valves.
•
pressure gauge.
•
controls – electrical keys board.
•
manualy operated hand pump 2 nos. Duly fitted with power pack
gm motorized ctrb extractor gm ctrb 100 is being developed in a unique concept as mobile work station (motorized high pressure extractor) to dismount direct mounted roller bearings (bearing no. 22320, 22326, 22328, 22330 )without damage or scoring to the component bore or shaft seating, with minimal force.
features & accesories
•
portable & assembled on 3 / 4 wheel trolley.
•
hydraulic power pack (max. Working pressure 750bars)
Rev Aircon India Pvt. Ltd. Supplying heating equipments, hot water heating coils, vertically mounted hot water heating coils, corrugated plate type hot water heating coils, heating coil, economiser coil and industrial hot water heating coils.
Unitherm Inductoweld (India) Pvt. Ltd. Engaged in manufacturing and supplying vast range of heaters like induction heaters, high frequency induction heaters, medium frequency induction heaters, heat treatment induction heaters and industrial heaters etc.
B. K. Electricals Exporter and manufacturer of heaters like mica band heaters, ceramic band heaters, industrial heaters, water immersion heaters, tubular heaters, tubular heaters, bobbin type open porcelain heaters and strip heaters.
Processing...
