Welding Equipment

We offer the clients with water & air cooled TIG Welding Torches, which are available in 6 variants. These are moulded using resin or rubber, and have varying lead lengths. The features of each version of this machine are listed below:

Product	Model	Features
TIG Welding Torch – Water Cooled	SWE–HWW–100–600	Torch with 4/6/8 m long lead Rubber moulded/ Resin mould
TIG Welding Torch Air – Cooled	SWE–HWW–100–300	Torch with 4/6/8 m long lead Rubber moulded/ Resin mould
Plazma Cutting Torch	SWE – HC 400 to 1000	Hand cutting torch for 50 to 100 mm thick stainless steel plates
Pencil Torch - Water Cooled	SWE–HWW–100–600	Torch with 4/6/8 m long lead Rubber moulded/ Resin mould
Plazma Cutting	SWE –HC 400 to 1000	Cuts 50 to 100 mm thick stainless steel plates
Plazma Cutting Torch	SWE – HC 300 to 1000	Cuts 50 to 100 mm thick stainless steel plates

The Air Welding Rectifiers offered by us are developed keeping in mind the DC welding current requirements of operations that have 3 phase, 50 Hz, AC mains power. These run on voltages ranging from 415 to 440 V, and are manufactured from 100 % copper wound. This equipment is ideal for conducting manual arc welding operations.

MODEL	HTE–400 AMP	HTE–600 AMP
Rated KVA	34	45
Supply Voltage	380 - 440 V	380 - 440 V
Phase	3	3
Frequency	50 Hz	50 Hz
Primary Current	32 A	64 A
D.C. Voltage ( O.C.V. )	80 - 90 V	80 - 90 V
D.C. Amp. 60% Duty Cycle	60 - 400 A	80 - 600 A
Insulation Class	H	H
Cable Section	10 mm2	16 mm
Welding Cable Section	50 mm2	95 mm2

These rectifiers are suitable for manual arc welding of:

• Pipes in all positions where welds of high radiographic standard are required
• Non - ferrous metals
• Low - alloy, corrosion , heat and creep resisting, steels
• High efficiency energy saving
• Mild steel at sites where AC welding power may be unsuitable.
• The STS may be Supplied with
• Suitable ammeters & volt meters for direct reading of the welding current
• Remote current control devise as optional extras

Some of the special features of this product are:

• Excellent welding characteristics
• Uses a Three phase, full wave silicon rectifier bridge in combinations with a well designed transductor and output choke to give a smooth & steady arc with minimum spatter and weld bead
• Minimum to maximum current is achievable in a single range thus obviating the need for cumbersome range selection
• Designed for easy arc striking with all type of electrodes
• Surge suppressor device to protect the machine from input voltage spikes
• Built in safeguards to protect against over load or heating
• Excellent for gouging applications also
• Light weight & easily maneuverable
• Easy to maintain

The Argon & CO2 Flow Meters available with us are regulator & heater assemblies that are powered by the two elements. These are well received in the market, and are renowned for the output generated in the process. Their welding accuracy is exceptional, and is considered the best in its class. Through this product, we are serving many reputed companies that carry out welding operations in their processes.

We introduce the DC Suppressor Units, which find their application in balancing output waves from transformers. This product is especially required for conducting the operations on aluminium, a light and strong metal. These are manufactured using high grade basic material, which provides them with optimum strength & longer operating life. It carries out the operations in accordance with all applicable industry norms, and adheres to the requisite standards of the industry.