Our extensive assortment of Distribution Boards Enclosure is an indispensible part of the electronics market. Metal enclosures are fabricated from continuous length of sheet steel which is double folded in front and with back welded into the frame.  These are protected both internally and externally with polyester epoxy resin grey paint. For better performance we manufacture it with perforated door reinforcement profiles allowing fixing of equipment and welded studs on the back for direct fixing of mounting plate and other accessories.   

Following are some of the features of our Distribution Boards Enclosure:

• 300 x 300 x 132 mm Empty Enclosure Distribution Board
• IP 65 empty enclosure
• U = 690 V
• With adapters, locking and insulating seals

(Stainless Steel DBs/Distribution Boards are manufactured on special orders)

Bus bar in an electrical power distribution is referred to thick strips of copper or aluminum that allows conduction of electricity within a switchboard, distribution board, substation, or other electrical apparatus. "Bus bar systems" is about conductors that take the form of a bar or bars of copper conductor where in bars may be exposed or enclosed. This system may be developed with one or more joints to ensure proper length and configuration with one or more take-off points connected to end-use equipment.

Since we understand the fact that the size of the bus bar is important in determining the maximum amount of current that can be safely carried; we therefore manufacture it precisely. Bus bars can have a cross-sectional area of as little as 10 mm² but electrical substations may use metal tubes of 50 mm in diameter (1,000 mm²) or more as busbars.

We manufacture busbars which are typically either flat strips or hollow tubes in accordance to the heat that has to be dissipated more efficiently due to their high surface area to cross-sectional area ratio. Hollow or flat shapes are prevalent in higher current applications as the skin effect makes 50-60 Hz AC bus bars more than about 8 mm (1/3 in) thick inefficient. A hollow section has higher stiffness than a solid rod, which allows a greater span between bus bar supports in outdoor switchyards.

Cited below are some of the features of our bus bars are as follows:

• Fulfills the safety parameters
• Corrosion Free
• Durable

Available with :

• 32 Amps
• 63 Amps
• 100 Amps
• 200 Amps
• 320 Amps

Our Phase-Changer three phase converter changes a 240V or 480V single phase supply into an equivalent 415V 3-phase output, which is equivalent to a utility 3 phase supply. It efficiently operates on any 3 phase equipment. With the easy availability of Phase power, there is always a Phase-Changer 3 phase converter solution that will reliably power any 3 phase machine. Workshop equipment, welders, compressors, pumps, computer controlled machines, air conditioners, in fact anything that requires 3 phase power changer.

Salient features of our Phase Changer are as follows:  

• 3 Phase power can be operated by a Phase-Changer converter
• Even big "hard to start" loads will start & run reliably with power from a Phase- Changer
• Longer functionality

We fabricate and supply an extensive array of switchgear which is used in association with the electric power system or grid. This also refers to the combination of electrical disconnects, fuses and circuit breakers which has widespread application in isolating electrical equipment. Our specialized switchgear is used for both de-energizing equipment in order to allow work to be done and to clear faults downstream.

Some of the attributes of our switch gear are as follows:

• Fulfills the safety parameters
• Corrosion Free
• Durable

Leveraging on our technical expertise and in-house facilities, we are enabled to manufacture Triple Pole Distribution Box. We follow industry recommended standards and our entire assortment fulfills the safety parameters of the industry. These are offered with neutral, busbar, incoming contact, din channel and others. It is powder coated with sheet steel enclosure flush/ surface mounting and fitted with bus bar, din channel, neutral link & incoming contact (without MCB's)for three phase connection.

Following are some of the features of our Triple Pole Distribution Box:

• Durable
• Corrosion resistant
• Precise designs 

Our assortment of Sheet Metal Double pole and four pole change over switches are specially designed for various modern industrial uses. Its application involves control power from sources.  These are housed in deep drawn CR sheet steel enclosure for 16 to 63 Amps and fabricated for 100 to 400 Amps. To make it more clients specific, we can also alter the standard forms.

Following are some of the features of our Sheet Metal Change Over Double Pole:

• Sheet Steel enclosures with best quality powder coating
• The housing goes through a rigorous anti-rust conditioning with seven tank system
• Versatile application areas

Types:

• Single Pole(16/32) Amp
• Double Pole(16/32) Amp
• Triple Pole/Four Pole(32/63/100/200/320) Amp

Painted/Plated/Powder Coated/Galvanized All tray are in 2.5 meter size

We fabricate a wide array of perforated cable trays using mild steel, stainless steel, aluminum, FRP, GRP along with pre-galvanized steel, hot dip galvanized, enamel painted and powder coated. Owing to our in-house facilities we offer perforated cable trays of up to 6000mm / 20 Feet In length. These are offered along with accessories including bends (horizontal, vertical, inside and outside), reducers, crosses, tees, clamps and others.  Along with this we also manufacture ladder type cable trays, wire mesh type, aluminum trays, FRP cable trays, special supporting systems, cable race ways and trunking.

Types of Perforated Cable Tray:

• Light duty straight flange perforated cable trays
• Medium duty straight flange perforated cable trays
• Heavy duty straight flange perforated cable trays
• Heavy duty inward bend & return flange cable trays
• Heavy duty inward bend & return flange cable trays connecting pieces, slotted angles for support of the tray are all also available
• Standard cable trays can be ordered and supplied and it can also be as per the project specifications
• (2/3/4/6/8/10/12) etc sizes in inches
  

Our technical expertise helps us manufacture a wide range of horizontal perforated Cross & Tee type cable trays in the width from 50mm to 1000mm and depth from 20mm to 150mm with the thickness ranging from 1mm to 3mm with all accessories. The basic materials used in fabrication of our Horizontal Perforated Cross & Tee are Mild steel, Aluminum, Stainless steel, Galvanized Iron and offered with painted, epoxy coated, h.d. galvanized and anodized finishings.

Following are some of the features of our Horizontal Perforated Cross & Tee:

• Equal Reducer
• Vertical inside Elbow
• Vertical outside Elbow
• 90 Degree Horizontal Bend
• Perforated Horizontal Cross Piece
• Perforated Tee

We also fabricate and supply Sheet Metal Ladder Type Tray in accordance to the industry recommended standards. Our ladder-type cable tray are specially designed for cables and similar types, the ladder including one or more pairs of L-shaped side rail members having vertical and horizontal sides, the vertical side having formed therein a protruding spring tab is posed above a socket.

One or more of U-shaped rung members formed at either end with a flange enclosing a U-shaped opening and defining a folded edge terminating is there in at least one tooth. The folded edge having formed therein a slot for engaging the spring tab such that upon insertion of the rung member tooth into the socket on the side-rail, the spring tab is deflected laterally and returns to its position to engage the locking slot in the rung and lock the rung to the side-rail. The locked rung then forms a support platform for the cable in a rigid fashion.

Cited below are some of the features of our Sheet Metal Ladder Type Tray:

• Versatile application areas
• Precise designs
• Lasting finish

Paint/Powder Coated/ Galvanized coating
Medium Duty Straight Flange Cable Trays are an effective way to mange wiring while keeping it accessible, organized and secure. These are available in different sizes and with different specifications such as painted, hot dip galvanized or powder coated. Our system is specially designed to accommodate numerous branch lines and offer high load-bearing capacity. Technicians can install one or more dividers to separate power and data lines and organize cabling. In order to add cabling protection, our clients can use our perforated cable tray with or without covers. Ventilated louvers can also be specified to facilitate cooling by natural convection while keeping conductors enclosed and protected. Our range of perforated cable tray may be hung using center rod support, C-hanger, or two hanger trapeze configuration and they can also be wall mounted using brackets.

Customization can be offered in the following parameters:

• Paint
• Inside bend
• Outside bend

We are providing premium quality meter boxes that contain the electric meter and the main electrical breaker panel. The range that we offer are known for easy installation and maximum durability. Used in home, offices, hospitals, schools etc these meter boxes are available at reasonable pricing.
Following are some of the features of our El;ectrical Meter Boxes:

• Durable
• Precise designs

We are providing high quality Kit Kat fuses which are having the following features:

• Utilizing top quality porcelain.
• Best quality Brass, Phosphorus Bronze components and ETP copper contacts are heavily silver plated to improve the high conductivity