IC-XX Series Interfacing Modules are useful for Teaching/Training to interface with any Microprocessor, Microcontroller, Embedded and VLSI Trainer Kits. These Modules are designed to interface with 8255, MCU Port I/O’s, 50 Pin KXT Bus. All the Interfacing Modules are enclosed in ABS Plastic enclosures.

SC-XX Series Study Cards can be connected to the 50 Pins KXT Bus of any 8/16 bit Series Microprocessor Trainer Kits. In this Study Card LED is provided for different signals like Read, Write, Address Lines, Data Lines, Chip Select & Ports depending upon the Peripherals. All the Study Cards are enclosed in ABS Plastic enclosures.

IC-01 ADC - 0809 Interfacing Module

ADC module using ADC-0809.
8 bit accuracy ADC chip
Eight Channel on-chip multiplexed ADC.
A/D Conversion time 100 micro sec.
SOC, EOC, O/P enable can be accessed by user.
Provision of 0 to 5V variable source using Potentiometer for one channel.
Eight channel analog inputs are to be provided on Screw Terminals.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-02 DAC - 0800 Interfacing Module

DAC module using DAC-0800.
8 bit accuracy DAC chip
Dual channel DAC using 2 Nos. of DAC-0800.
DAC settling time is 100 ns
DAC output is provided at two test points.
Connect to 8255 using 26 pin FRC connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-03 AD - 574 Interfacing Module

ADC module using AD-574 chip.
12 bit accuracy ADC chip
Single channel ADC module.
A/D conversion time of 15 micro sec.
Analog inputs are provided at screw terminals.
Connect to 8255 using 26 pin FRC connector.
User's manual with sample programs


	Send Trade Enquiry

IC-04 Digital I/O Interfacing Module

8 Digital Inputs provided using 8 way DIP Switch
8 Input LED Indicators are provided
8 Output LED Indicators are provided
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-05 Elevator Simulator Module

Four floor elevator simulator model
LED indication for Each Floor is provided
Up & Down Lift position indication by 10 Nos. of LED
Each Floor is accessed using Four Keys provided on board.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-06 IC Tester IM For IC - 7400

On-board two nos. of 14 pin socket and one no. of 16 pin Socket provided.
One 14 Pin IC-7400 IC is provided for testing.
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-07 Four Digit Seven Segment Display.

Four digit seven segment display.
Display technique used is serial in parallel out shift register technique
For this technique two port pins are used for display.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-08 Stepper Motor Controller Card With Motor

This Card can Control a Two/Four phase motor
Half Step, Full Step can be controlled using this card.
Clock Wise & Anti Clock wise rotations can be controlled
Speed can be controlled by this controller
Facility to control maximum 2Kg cm Motor is provided.
0.25Kg cm Stepper Motor is supplied along with this module.
Provision for connecting external 5V/12V supply to drive the motor
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-09 5x4 Keys Matrix Keyboard Interface Module

5x4 Keys matrix Keyboard.
Keyboard consists of 20 keys.
Consist of hexadecimal numerals from 0 to 13.
Keys are organized as Four Rows & Five Columns Matrix
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-10 16x1 LCD Display Module

16x1 Liquid Crystal Display.
One 16 rows Alphanumeric Characters will be Displayed.
Facility for back lite display.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-11 16x2 LCD Display Module

16x2 Liquid Crystal Display.
Two 16 rows alphanumeric characters will be displayed.
Facility for back lite display.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-12 Traffic Light Controller Module

Single Square traffic light display controller
East, west, north, south posts are defined on the PCB for the square.
For each post four LED is provided in Red, Yellow & Green color.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-13 Temperature Measurement Module

ADC-0809 is used for analog to digital conversion.
8 bit accuracy ADC chip
A/D Conversion time is 100 micro sec.
Op-amps are provided for signal conditioning of output from sensor.
K-type thermocouple is used for the measurement.
Thermocouple sensor is supplied with the module.
Variable pot is provided for adjusting gain and offset.
Temperature measurement max. up to 99°C is possible
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-14 DC Motor Controller Card With Motor

DAC-0800 is used for digital to analog conversion.
8 bit accuracy DAC chip
SPDT Relay is provided for direction control
Clock Wise & Anti Clock wise rotation can be controlled
Speed can be controlled by this controller
9 Volt DC Motor is supplied with this card.
9 Volt AC Adaptor is supplied with this card.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-15 Relay And OPTO Coupler Interfacing Module

Four SPDT Relays are provided.
Relay outputs NO, NC, COM is provided at Screw Terminals.
Four Opto isolator inputs are provided using MCT2E.
Opto Inputs are provided through 10 pin FRC Connector.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-16 8x8 LED Matrix Interfacing Module

8x8 LED Matrix Display.
Display consists of 64 nos. of 3mm LED.
LED’s are organized as Eight Rows & Eight Columns matrix.
All LEDs are buffered.
Connect to 8255 using 26 pin FRC Connector
User's manual with sample programs.


	Send Trade Enquiry

IC-17 Thumb Wheel Switch Card

Two digit thumb wheel switch.
Thumb wheel switch can be set from 00 to 99.
Output of Thumb wheel switch is in BCD format.
Connect to 8255 using 26 pin FRC connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-18 Light Sensing Module Using LDR

Light Sensing device using LDR
For Alarm indication one SPDT Relay is provided.
Relay output is provided in connector.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-20 OPTO Isolated Input Module

8 bit OPTO Isolated input using MCT-2E IC.
OPTO inputs indication are provided by 5mm LED.
OPTO inputs are provided through 16 pin Connector.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-21 OPTO Isolated Output Module

8 bit OPTO Isolated output using MCT-2E IC.
OPTO outputs indication are provided by 5mm LED.
OPTO output are provided through 16 pin Connector
External +12V provision is provided for isolation.
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs


	Send Trade Enquiry

IC-22 101 ASC II Keyboard Module

101 ASCII PC Keyboard interface.
PC Keyboard interface through 89c2051 Microcontroller.
PC Keyboard AT-type Connector is provided
101 ASCII keyboard is provided with this module.
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-23 Real Time Clock (RTC - 6242) Module

Real Time Clock using IC 6242.
32.678 KHz. Crystal is provided.
Date, month & year can be measured.
Seconds, minutes & hours can be measured.
Connect through 40/50 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-24 Seven Segment Display With Matrix Keyboard

5x4 Keys matrix Keyboard.
Keyboard consists of 20 keys.
Consist of Hexadecimal numerals from 0 to 13.
Keys are organized as Four Rows & Five Columns matrix
Study of techniques like software debouching, Keyboard scanning, key closer, two keys lockout, keyboard encoding & Pausing.
16x2 Liquid Crystal Display.
Two 16 rows alphanumeric characters will be displayed.
Facility for backlite display.
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs


	Send Trade Enquiry

IC-25 16x2 LCD Display With Matrix Keyboard

5x4 Keys matrix Keyboard.
Keyboard consists of 20 keys.
Consist of Hexadecimal numerals from 0 to 13.
Keys are organized as four rows & five columns matrix
Study of techniques like software debouching, keyboard scanning, key closer, two keys lockout, keyboard encoding & Pausing.
16x2 Liquid Crystal Display.
Two 16 rows alphanumeric characters will be displayed.
Facility for back lite display.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs


	Send Trade Enquiry

IC-26 8 Bit AD / DA Interfacing Module

ADC module using ADC-0804.
8 bit accuracy ADC chip
Single Channel ADC.
A/D Conversion time 100 micro sec.
Single Channel DAC using one No. of DAC-0800
8 bit accuracy DAC chip
DAC Settling time is 100 ns
Analog inputs and outputs are provided on Screw Terminals.
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-27 Level Simulator Module

Four Level Simulator model
Level indication is provided using LED
Up & Down Level position indication by 10 Nos. of LED
Lower & upper level limit can be set by software
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample programs.


	Send Trade Enquiry

IC-28 Six Digit Seven Segment Display Module

On-board six digit seven segment display.
Display technique used is Decoder technique
For this technique two port pins are used for display.
Connect to 8255 using 26 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

IC-29 Parellel To Serial And Serial To Parallel Module

8 bit Parallel to serial convertor using IC-74165.
Eight Parallel Inputs are indicated by LED.
Serial to 8 bit parallel convertor using IC-74595.
Eight Parallel Outputs are indicated by LED.
Connect to 8255 using 26 pin FRC Connector.
User's manual with sample program.


	Send Trade Enquiry

SC-01 8255 Programmable Peripheral Interface Study Card

24 bit I/O using 8255 Programmable Peripheral IC
All Input/Output ports pins are terminated on 3 eight pin terminals and 26 pin FRC Connector
All Input/Output ports are indicated by 3 mm LED.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, A0, A1, Read, Write are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution mode are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-02 8253 Programmable Timer Counter Study Card

Three channel Timer/Counter using 8253 Programmable Timer Counter IC.
All Input/Output ports pins are terminated on terminals and 10 pin FRC Connector.
Clock for Counter-0 is internally provided.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, A0, A1, Read, Write are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-03 8155 Programmable Peripheral Interface With Timer

22 bit I/O with single channel timer using 8155 Programmable Peripherals IC
All Input/Output ports pins are terminated on 3 eight pin terminals and 26 pin FRC Connector
All Input/Output ports are indicated by 3 mm LED.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, IO, Memory, Read, Write are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-04 8251 USART Study Card

22 bit I/O with single channel timer using 8155 Programmable Peripherals IC
All Input/Output ports pins are terminated on 3 eight pin terminals and 26 pin FRC Connector
All Input/Output ports are indicated by 3 mm LED.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, IO, Memory, Read, Write are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-05 8257 Direct Memory Access Study Card

Programmable Direct Memory Access controller using 8257 IC.
On-board 2K RAM Provided using 6116 IC for DMA Operation.
8 Inputs are fed through input terminals with 3 mm LED indicator.
Data lines from AD0 to AD7 are indicated by 3mm LED.
Chip Select, Read, Write, A0, A1, A2, A3, Memory-Write,
Memory-Read, IO-Write, IO-Read are indicated by 3mm LED.
AEN, Mark, TC, HRQ, DACK0, DACK1, DACK2 are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs..


	Send Trade Enquiry

SC-06 8259 Programmable Interrupt Controller Study Card

8 Channel Programmable Interrupt Controller using 8259 IC.
8 Inputs interrupts are fed through input terminals.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, Read, Write, INTA, INTR are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-07 8279 PKDC Study Card

Programmable Keyboard Display Controller using 8279 IC.
All scan lines/return lines are fed through input terminals and 26 pin FRC connector.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, Read, Write, INTA, A0 are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution mode are provided.
Single stepping can be performed using micro switch provided in the board.
8 Digit Seven Segment display with 20 keys keypad interface module can be interfaced with 8279 Study Card. (Optional)
Using this study card all modes experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Program.


	Send Trade Enquiry

SC-08 8212 Latch Study Card

Eight bit Latch output using 8212 IC
Eight buffered latched output are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-09 Latch / Buffer Study Card

8 bit Latch output using 74373 IC.
8 bit Buffer input using 74245 IC.
8 buffered latch output are indicated by 3 mm LED.
Eight Way DIP Switch is provided for buffer input.
Eight bit buffered output are indicated by 3 mm LED.
Chip Select for IC-74245 and IC-74373 are indicated by 3 mm LED.
Hardware Single Step and Full Clock Execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

SC-10 6116/6264/32256 Ram Study Card

Random access memory using 6264 IC.
Data lines from AD0 to AD7 are indicated by 3 mm LED.
Chip Select, Read, Write are indicated by 3 mm LED.
Hardware single step and full clock execution modes are provided.
Single stepping can be performed using micro switch provided on board.
Using this study card all MODE experiment can be performed.
Interface 8085/8086 Kit using 50 pin FRC Connector.
User's Manual with Sample Programs.


	Send Trade Enquiry

Mr. Ajit Unnithan (Director)
B - 4, Lotus C. H. S., Near P. M. C. Bank, Sector - 7, Airoli
Mumbai, Maharashtra - 400 708, India
Telephone: +(91)-(22)-65116548/ 27694323/ 65126767