Krishna Colours

K coat is an anti-carbonation coating based on acrylic co polymers. Applied as a liquid it cures to form a durable, protective, waterproof membrane. It is a single component coating suitable for application by brush or roller.

Uses:

Highly recommended for exterior use on all types of plaster and concrete surfaces. Excellent weather resistant and has high scrub resistance. Can be applied directly on new and sound surfaces. To provide a smooth decorative durable coating for concrete and masonry surfaces. Two coat application is recommended.

Technical data:

• Chemical resistance : resistance to spillage of diesel, sewage, mild acids and alkalis.
• Water absorption : < 1 %
• Carbond dioxide diffusion : 6,90,000.
• Effective barrier to co2 :> 50 m.
• Colours : available in various colours.

Coverage:

Theoretical spreading rate : dry film thickness 50 – 100 micron will give 4 – 4. 5m² / kg. : wet film thickness 75 – 150 micron

Application

Surface preparation :

All loose material, including loose plaster, cement deposits, old paint, dust etc. Must be thoroughly removed. Chalking and porous substrates with high absorption.

Priming:

On old or porous surfaces, ensure that the substrate is sound and dilute 2 parts of kcoat to 1 part of water and prime the surface. When it is tacky or touch dry (i. E after 1/2 to 3 hours), apply kcoat on the primed surface.

Application :

Stirr the material in the container thoroughly and spread evenly with a brush, roller or airless spray. Avoid application during rainy weather. In hot, dry weather, dampen unpainted surfaces with water to prevent kcoat drying out too rapidly. Carbonation coating a two coat application (200 microns dft) is recommended.

Storage:

The product should be kept in well ventilated place, protected from heat and direct sunlight. Containers must be kept tightly closed.

Packing:

Available in 1, 5 & 20 kg. Plastic bucket.

Note:

All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

Anti Corrosive Protective Coating Ksealcore r is a two pack polymer based anti-corrosive protective coating for steel and reinforcement. Ksealcore r is thin section coating designed to provide weather resistance to steel and reinforcement. It ensures excellent corrosion resistance to the reinforcement bars.

uses

ksealcore can be used in steel reinforcement, embedded steel in concrete.

advantages

• excellent weather resistance.
• good bonding with concrete and steel substrates.
• protect the re bars from chloride and sulphates.
• economical and easy to apply.

application instructions
surface preparation :

the steel reinforcement should be cleaned by wire brush or acid cleaning.
all dust particles should be removed to achieve good bonding of coating.

mixing :

ksealcore r is supplied in two pack material with a powder component and the respective pre-weighed amount of liquid. The liquid should be poured into the suitable mixing vessel and the powder component gradually to be under mechanical mixing. The continuous mixing should be done until a homogenous colour is achieved. Application : the mixed ksealcore r should be applied by brush in one coat on substrate. And mixed material to be used with in 20 mins.

cleaning :

brush should be rinsed with water immediately after use.

packing & coverage

one pack (2kg + 1 litre) will cover approximately 100 kg of 12 diameter steel bar.

shelf life

12 months storage life when stored in original unopened container at between 5  ºc to 45 ºc in a dry and shaded place.

health & safety

ksealcore r is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.

note

all information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

ksealcore epx is a formulation of special epoxy and polyamide resin. It is a two part solvented epoxy protective and decorative coating for steel and concrete substrates. It provides protection from weathering and abrasion.

uses:

to protect steel and concrete surfaces. To penetration, abrasion and chemical attack.

enhance resistance to oil, grease, water

advantages:

* easy to apply by brush, roller or spray.

> prolectsand decorates.

> to enhance resistance to oil, grease, water penetration, abrasion and chemical attack.

> strong and hard wearing surface.

> easy to clean, hygienic, seamless floor.

> excellent adhesion and maximum protection.

> cost effective protective coating ' can be applied floor and walls

> can be used for rebars-does not effect bonding of concrete with steel.

 

application instructions:

surface preparation:

concrete substrates : the surface should be sound, free from laitance and contamination. It should be free from oil. Grease, etc. Must be removed using degreaser or detergent.

steel surfaces : oil contained surfaces should be thoroughly cleaned with kc degreaser, and sand blasting. Where this is not possible, minimal surface preparation with wire brushing should be done. Ksealcore ep(ls) can be applied directly to steel surfaces.

priming:

apply ksealcore primer epx as a primer coat on the smooth surface. The primer coat should be done 5 - shrs. Before applying ksealcore ep (ls).

mixing;

ksealcore ep(ls) is supplied ready to use in pre weighed packs of resin and hardener for easy on site mixing. Pour the hardener into the base can, and mix well, using a paddle attached to an electric drill, for 2-3 minutes until a uniform colour is obtained.

application;

ksealcore ep (ls) may be applied by brush or airless spray to give a continuous coating on the prepared surface. A second coat may be subsequently applied when first coat is dried. Preferably next day.

typical properties:
colour	red, blue, green, ivory, yellow & grey (special shade onrequest)
pot life	lhoursat30*c.
touch drv	8hoursat30*c.
fullcure	7 days.
temperature range during application :	5*ct04s'c.

coverage:

approximate coverage is 2 to 3m' / kg. / 200 microns.

practically coverage depends upon substrate and method of application.

 

precaution:

wear protective gloves and eye goggles while handling.

packing:

1 kg. 8 5 kg. Tin.

shelf life:

12 months storage life when stored in original unopened container at between 5 *c to 45 *c in a dry and shaded place.

health & safety:

ksealcore ep (ls) is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.

KSEALCORE epoxy floor coating is a two part solvent free epoxy resin based floor coating consisting of a pigmented base resin and a clear hardener component. The floor coating is available in a range of colours.

USES

• Protective coating for old and new concrete.
• Aesthetic finish to patch-repaired concrete to give uniform pleasing appearance.
• Ware house, storage areas and show rooms.
• Light industrial factory areas to gives resistance to foot and light vehicular traffic.
• Also used for anti-slip appearance.
• Early application to concrete surfaces to prevent ingress of aggressive substances in to immature concrete.
• Floor coatings for kitchens and other food processing areas.
• Used as a top coat in conjunction with water based epoxy coating and non-slip grains to form a slip resistant surfacing.

ADVANTAGES

• Easy to apply by brush, roller or spray.
• Protects and decorates.
• The applied coating is resistant to abrasive wear and to the penetration of oiland greases
• The two part solvent free product is pre-packaged ready for on site mixing without any risk from solvent vapours.
• High build and “hiding power” may be achieved in two coats giving 400 microns thickness of application.
• Strong and hard wearing surface.
• Easy to clean, hygienic, seamless floor.
• Excellent adhesion and maximum protection.
• A non slip finish obtained when the first coating is broadcast with non-slip grains.

APPLICATION INSTRUCTIONS

Surface preparation

All contact surfaces must be sound, clean, and dry and provide a good mechanical key. Remove all loose material, paint, plaster and oily deposits. For
best results, light grit blasting is recommended.

PRIMING

Apply KSEALCORE WB PRIMER as a primer coat on the smooth surface. The primer coat should be done 5 – 8 hrs. before applying KSEALCORE.

MIXING

KSEALCORE is supplied ready to use in pre weighed packs of resin and hardener for easy on site mixing. Pour the HARDENER into the BASE
can, and mix well, using a paddle attached to an electric drill, for 2-3 minutes until a uniform colour is obtained.

APPLICATION

KSEALCORE may be applied by brush or airless spray to give a continuous coating on the prepared surface. A second coat may be subsequently applied when first coat is dried. Preferably next day.

TYPICAL PROPERTIES

• COLOUR : Red, Blue, Green, Ivory, Yellow & Grey (special shade on request)
• POT LIFE : 45 min. at 30 0C.
• TEMPERATURE RANGE DURING APPLICATION: 5 0C TO 45 0C.

Typical curing times at 20°C

• Overcoat 12 to 24 Hours
• Foot traffic 36 to 48 Hours
• Full cure 7 Days

COVERAGE

• Approximate coverage is 9 to 10m2 / 5 kg. / 400 microns.
• Practically coverage depends upon substrate and method of application.

PRECAUTION

• Wear protective gloves and eye goggles while handling.

PACKING

• 1 kg. & 5 kg. tin.

SHELF LIFE

12 months storage life when stored in original unopened container at between 5 ºC to 45 ºC in a dry and shaded place.

HEALTH & SAFETY

KSEALCORE is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.

Epoxy Protective Coating Ksealcore epx is a formulation of special epoxy and polyamide resin. It is a two part solvented epoxy protective and decorative coating for steel and concrete substrates. It provides protection from weathering and abrasion.

Uses:

To protect steel and concrete surfaces. To enhance resistance to oil, grease, water
penetration, abrasion and chemical attack.

Advantages:

• Easy to apply by brush, roller or spray.
• Protects and decorates.
• To enhance resistance to oil, grease, water penetration, abrasion and chemical attack.
• Strong and hard wearing surface.
• Easy to clean, hygienic, seamless floor.
• Excellent adhesion and maximum protection.
• Cost effective protective coating
• Can be applied floor and walls
• Can be used for rebars-does not effect bonding of concrete with steel.

Application Instructions:

Surface Preparation

Concrete Substrates : The surface should be sound, free from laitance and contamination. It should be free from oil, grease, etc. Must be removed using degreaser or detergent. Steel surfaces : oil contained surfaces should be thoroughly cleaned with kc degreaser, and sand blasting. Where this is not possible, minimal surface preparation with wire brushing should be done.

Ksealcore ep (ls)

• Can be applied directly to steel surfaces.

Priming:

Apply Ksealcore Primer EPX as a primer coat on the smooth surface. The primer coat should be done 5 – 8 hrs. Before applying ksealcore ep (ls)

Mixing:

Ksealcore ep (ls) is supplied ready to use in pre weighed packs of resin and hardener for easy on site mixing. Pour the hardener into the base can, and mix well, using a paddle attached to an electric drill, for 2-3 minutes until a uniform colour is obtained.

Application:

Ksealcore ep (ls) may be applied by brush or airless spray to give a continuous coating on the prepared surface. A second coat may be subsequently applied when first coat is dried. Preferably next day.

Typical Properties:

• Colour : red, blue, green, ivory, yellow & grey (special shade on request)
• Pot Life : 1 hours at 30 0c.
• Touch Dry : 8 hours at 30 0c.
• Full Cure : 7 days.
• Temperature Range During Application : 5 0c to 45 0c.

Coverage:

• Approximate coverage is 2 to 3m2 / kg. / 200 microns.
• Practically coverage depends upon substrate and method of application.

Precaution:

• Wear Protective Gloves and Eye Goggles while handling.

Packing:

• 1 kg. & 5 kg. Tin.

Shelf Life:

12 months storage life when stored in original unopened container at between 5 ºc to 45 ºc in a dry and shaded place.

Health & Safety:

Ksealcore ep (ls) is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.

Note:

All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

Description:

Polyamlde Resin Coating KSEALCORE EPX is a formulation of special epoxy and polyamlde resin. It is a two part solvented epoxy protective and decorative coating for concrete floors.

Protective coating for old and new concrete.

Aesthetic finish to patch-repaired concrete to give uniform pleasing appearance.

Ware house, storage areas and show rooms.

Light industrial factory areas to gives resistance to foot and light vehicular traffic.

> Also used lor anti-slip appearance.

> Early application to concrete surfaces to prevent ingress of aggressive substances in to immature concrete.

 

Advantages:

> Easy to apply by brush, roller or spray. ' Protects and decorates.

> Moisture vapour permeable.

r Strong and hard wearing surface.

> Easy to clean, hygienic, seamless floor.

> Excellent adhesion and maximum protection

 

Application Instructions:

SURFACE PREPARATION:

Concrete Substrates : The surface should be sound, free from laitance and contamination. It should be free from oil, grease, etc. must be removed using degreaseror detergent.

 

Priming;

Apply KSEALCORE PRIMER EPX as a primer coat on the smooth surface. The primer coat should be done 5 -Shrs. before applying KSEALCORE EPX.

Mixing;

KSEALCORE EPX is supplied ready to use in pre weighed packs of resin and hardener for easy on site mixing. Pour the HARDENER into the BASE can, and mix well, using a paddle attached to an electric drill, for 2-3 minutes until a uniform colour is obtained.

Application:

KSEALCORE EPX may be applied by brush or airless spray to give a continuous coating on the prepared surface. A second coat may be subsequently applied when first coat is dried. Preferably next day.

 

Typical Properties :
COLOUR	Red, Blue, Green, Ivory, Yellow & Grey (special shade on request)
POT LIFE	lhoursat30"C.
TOUCH DRV	8hoursat30"C.
FULLCURE	7 DAYS.
TEMPERATURE RANGE DURING APPLICATION :	5"CTO4S'C.

Coverage:

Approximate coverage is 2 to 3m / kg. / 200 microns.

Practically coverage depends upon substrateand method of application.

Precaution:

Wear protective gloves and eye goggles while handling.

Packing:

1 kg. & 5 kg. tin.

 

Shelf Life:

12 months storage life when stored in original unopened container at between 5 "C to 45 "C in a dry and shaded place.

Health & Safety:

KSEALCORE EPX Is non-hazardous. It should not be swallowed or allowed to come Into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.