Krishna Colours

Cement Adhesives K95 READYPLAST FB (I) is a ready to mix, dry cementitious fiber reinforcement internal plaster. It contains blended cements, graded sands, polypropylene fiber and additives to improve consistency and workability.

Smooth under layer material (or exterior and interior concrete, masonry or plaster based substrates.

Interior final finishing plasters for walls and ceilings or concrete and block surfaces.

It can be used on brick, block, patching honeycombs in concrete to improve the quality of plastering work by factory controlled product.

Advantages:

 

• Ease of use, requires only the addition of clean cold water

• Durable finish

• Better coverage in plaster area

• Excellent bonding, less rebound hence reduces the wastages during plastering

• Excellent permeability resistant

• Increased plastic life of mortar and reduces drying shrinkage cracks

• Improved labor productivity hence reduces the cost so it is economical

• Paintable, Once hardened

Application Instructions:

The surface should be clean, free from standing water and all contaminants such as oil, grease, laitance, paint, or corrosion products. Any contamination should be removed by mechanical means to produce a sound substrate. The surface should be washed with clean water to remove all dust. It should be wetted prior to application of K9S READYPLAST FB (I). The product should not be applied to surfaces which are exposed to running water.

 

Mixing;

K95 READYPLAST FB (I) Complete bags should be mixed using a mechanically powered grout mixer. Each bag requires 6 to 7 Itr ol clean cold water. Ensure that the mixer is damp inside but free of standing water before commencing mixing; add pre-measured quantity of clean cold water.

Application:

Apply the mixed K95 READYPLAST FB (I) by hand using a steel trowel. Use a float to give a smooth and uniform thickness and level surface. Mixed K9S READYPLAST after adding water, should be used within 45 minutes.

Curing:

Water curing is recommended after 16 hours and to be continued for at least 7 days. Alternatively curing by KCURE C curing compound is recommended.

Cleaning;

Tools contaminated with K95 READYPLAST F8 (I) can be cleaned using clean water. Hardened grout can only be removed by mechanical means.

Health & Safety:

K95 READYPLAST FB(I) Is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.

Packing & Coverage :

K95 READYPLAST F8 (I) is available in 40 Kg. bags. 40 kg. Bag of bag K95 READYPLAST FB (I) will cover 30-32 sq.fl in 15-16 mm thickness the coverage depends upon the substrate.

Storage:

9 months storage life when stored in original unopened bags at between 5 and 35'C in a dry and shaded place.

 

 

Cement Based Mortar k95 readyplast fbe is a premixed fiber reinforced ready to use cement based mortar for external as well as internal plaster which ensures waterproof, crack free plaster of consistent quality. . K95 readyplast fbe is a mixture of graded inert fillers, additives binder and fiber. Generally meets the requirements of is 2250-1981.

Benefits:

r readymixfactory controlled mortar.

> assured quality of plaster.

> excellent permeability resistance ensures perfect watertightness.

^ better coverage in plastered area.

> good bonding, less rebound wastage during plastering.

> better water retention properties, hence plastic life of mortar.

> reinforced with cement compatible fibers to reduce drying shrinkage area other cracks.

> increased plastic life of mortar.

> ideal for external plaster.

> enhanced labour productivity hence reduces thecost.

> free from corrosion inducing substances.

Purpose:

k95 readyplast fbe can be used to improve the quality of external and internal plastering work by factory controlled product.

packing;

25 kg, 40 kg of woven bag.

application;

Mixing:

take precise quantity of water & pour into mechanical mixer or can be loaded into plastering machine and slowly add the k95 readyplast fbe mortar into mixer at a ratio of 0. 15 w/p ratio and mix it thoroughly for application.

Application:

clean the substrate take out loose particles. Wet the surface except those of cement concrete blocks thoroughly and apply k95 readyplast fbe to achieve uniform thickness and level surface. Mixed k95 readyplast fbe after adding water should be used within 60 minutes.

Curing:

water curing is recommended after 12 hours and to be continued for atleast 7 days.

Typical Properties:

Physical Form Powder Colour : cementgrey

airentrainment 8tol0%when mixed.

coverage;

depending upon quality of substrate, 40kg bag of k95 readyplast fbe can cover about 16-18sq. Ft. In 12-15 mm thickness.

shelf life;

13 weeks if stored in cool, dry shade.

Technical Service:

while new advances and changes will take place one thing will never change is quality and meeting special needs of customer. Technical personnel & experts are available to provide additional information and technical assistance. We are eager to work with you in development of new product and solve your problem. the information given in this data sheet is based on both current development work and may years field experience. Whilst every effort is made to ensure that the information is reliable, we can not accept responsibility for any work carried out with our materials as we have no control over methods of application, site conditions etc. In view of the continuing research and development being undertaken in our laboratories we advise customers in their own interest to ensure that this data sheet has not been supersede by a more up-to-date publication. All products are sold subject to our standard conditions of sale which are available on request. Field services, where provided, does not constitute supervisory responsibility. For additional information, please contact your local representative.

Ready Mix Water Resist Colored Plaster

Description;

K5 REAOYPLAST RC is a ready to mix, dry cementitious coloured plaster. It contains blended cements, graded sands and additives to improve consistency and workability. It Is cement based mortar for external as well as internal plaster.

Smooth under layer material for exterior and interior concrete, masonry or plaster based substrates.

Interior or exterior final finishing plasters for walls and ceilings or concrete and block surfaces.

Advantages;

> Ease of use, requires only the addition of clean cold water.

> Durable finish.

> Better coverage in plaster area.

> Excellent bonding, less rebound hence reduces the wastages during plastering.

> Excellent permeability resistant.

> Increased plastic life of mortar and reduces drying shrinkage cracks.

> Improved labor productivity hence reduces the cost so it is economical.

> Paintable. Once hardened.

> Available in various colour

Application Instructions:

The surface should be clean, free from standing water and all contaminants such as oil, grease, laltance, paint, or corrosion products. Any contamination should be removed by mechanical means to produce a sound substrate. The surface should be washed with clean water to remove all dust. It should be wetted prior to application of KS READYPLAST RC. The product should not be applied to surfaces which are exposed to running water.

Mixing:

KS READYPLAST RC Complete bags should be mixed using a mechanically powered grout mixer. Each bag requires 6 to 7 Itr of clean cold water. Ensure that the mixer is damp inside but free of standing water before commencing mixing; add pre-measured quantity of clean cold water.

Application:

Apply the mixed KS READYPLAST RC by hand using a steel trowel. Use a float to give a smooth and uniform thickness and level surface. Mixed KS READYPLAST RC after adding water, should be used within 45 minutes.

Curing:

Water curing is recommended after 16 hours and to be continued for at least 7 days. Alternatively curing by KCURE C curing compound is recommended.

Cleaning:

Tools contaminated with K5 READYPLAST RC can be cleaned using clean water. Hardened grout can only be removed by mechanical means.

Health & Safety:

K5 READYPLAST RC is non-hazardous. It should not be swallowed or allowed to come into contact with skin or eyes. Suitable protective goggles and gloves should be worn. In the case of contact with eyes, rinse Immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately, do not induce vomiting.

Packing & Coverage:

KS READYPLAST RC is available in 40 Kg. bags. 40 kg. Bag of bag K5 READYPLAST RC will cover 15-16 sq.ft in 15-16 mm thickness the coverage depends upon the substrate.

Storage:

9 months storage life when stored in original unopened bags at between 5 and 35°C in a dry and shaded place.

JAIFIX TG STD is a ready to use cementitious tile grout for the permanent grouting of ceramic tiles in both damp and totally submerged conditions.

USES

• Mainly used for swimming pool tile grouting.
• For filling of tile joints in kitchens and bathrooms.
• Recommended for all porous and absorbent wall and floor tiles.
• Can be used for Tile joints width of 3 mm to 13 mm.
• It can be used on material such as ceramic wall tiles, clinkers and mosaics.

ADVANTAGES

• Non-shrinking
• Chemical resistant
• Water resistant
• No wet curing required
• Non yellowing.
• Hard wearing.
• Cost effective.

APPLICATION

• As a general role on a porous surface, allow 24 hours for tiles to set prior to grouting.
• Ensure the gaps between the tiles are clean, dry and free of adhesive.

MIXING :

• Mix complete bag of powder into the potable water with a partial slow speed.
• Drill until lump free paste is obtained. The ratio of 1 : 3 against powder and water by weight to be followed.

APPLICATION :

• Apply JAIFIX TG STD to the spaces between tiles with proper rubber float or sponge, ensuring the joints and edges are completely filled and compacted.
• Remove surplus plaster with damp cloth.
• When the grout is dry, polish tiles with clean, dry, soft cloth.

TYPICAL PROPERTIES

• Working time of grout paste : 40 minutes at 20ºC/ 20 Minutes at 35ºC
• Flammability : Non-flammable.
• Coverage meter : 1 Kg. of mixed product will cover 24 meter per joint 6 mm wide X 3 mm
• Depth. 12 mtr. / Kg. / 12 mm wide X 3 mm depth.

PACKING

• JAIFIX TG STD is available in 500 gms. And 1 kg .

STORAGE

12 months storage life when stored in original unopened bags at between 5 and 45ºC in a dry and shaded place.

NOTE

All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.

A Hard Wearing, Water Resistant Grout For Filling Joints Of Tiles

Benefits:

> JAIFIX TG is a hard wearing, water resistant grout for filling joints in exterior and interior walls and floor tiles, mosaics and clinkers up to 5mm width.

> It is easily applied by hand and because of its unique composition does not shrink when dry.

 

Properties:

> JAIFIX TG is composed of precisely graded, pure crystalline, marble powder, a blend of special cements, water-repellent materials, oxide colours and plasticizers.

 

> JAIFIX TG does not curl up during application and gives a wear and weather resistant joint with no shrinkage cracks.

 

Areas of Use:

JAIFIX TG can be used on material such as ceramic wall and floor tiles, clinkers and mosaics, where joints do not exceed 5 mm width.

Preparation of Surface:

Ensure all tile joints and edges are clean and free of exceeds tile fixing mortar.

Mixing:

Thoroughly mix JAIFIX TG in the ratio of 1 Itr water to 3 kg. JAIFIX TG powder. Allow to stand for 15 minutes. Stir again before use.

Application:

Wait until JAIFIX TA has set (approx 24 hours) before grouting. Apply JAIFIX TG diagonally into the joints with a rubber edged spatula. Remove excess grout with a moist sponge before drying. Do not apply grout to an area which is so large that it cannot be completed within an hour. Porous tiles should be moistened with water before grouting. After the grout has dried and before it has hardened, polish the tiles with a clean, dry cloth leaving the joints flush with the tiles, 24 hours after grouting, moisten the joins with a wet sponge.

Consumption:

1Kg of JAIFIX TG covers approximately 30 running ft. with 2mm width of joint.

Packing & Storage:

JAIFIX TG is supplied in 25 kg. and 5 kg sacks, and 1 kg containers. JAIFIX TG should be stored in clean, cool, dry area protected from direct light as supplied. Original unopened sacks can be stored for 12 months.

Technical Service;

While new advances and changes will take place one thing will never change is quality and meeting special needs of customer. We are eager to work with you in development of new product and solve your problem.

 

Water Resistent Grout JAIFIX TG is a hard wearing, water resistant grout for filling joints in exterior and interior walls and floor tiles, mosaics and clinkers up to 5mm width. l It is easily applied by hand and because of its unique composition does not shrink when dry.


Properties:

JAIFIX TG is composed of precisely graded, pure crystalline, marble powder, a blend of special cements, water-repellent materials, oxide colours and plasticizers.  JAIFIX TG does not curl up during application and gives a wear and weather resistant joint with no shrinkage cracks.


Areas of use:

JAIFIX TG can be used on material such as ceramic wall and floor tiles, clinkers and mosaics, where joints do not exceed 5mm width.

Preparation of surface:

Ensure all tile joints and edges are clean and free of exceeds tile fixing mortar.

Mixing:

Thoroughly mix JAIFIX TG in the ratio of 1 ltr water to 3 kg. JAIFIX TG powder.
Allow to stand for 15 minutes, Stir again before use.


Application:

Wait until JAIFIX TA has set (approx 24 hours) before grouting. Apply JAIFIX TG diagonally into the joints with a rubber edged spatula. Remove excess grout with a moist sponge before drying.

Do not apply grout to an area which is so large that it cannot be completed within an hour. Porous tiles should be moistened with water before grouting. After the grout has dried and before it has hardened, polish the tiles with a clean, dry cloth leaving the joints flush with the tiles, 24 hours after grouting, moisten the joins with a wet sponge.


Consumption:

1 Kg of JAIFIX TG covers approximately 30 running ft. with 2mm width of joint.


Packing and storage:

JAIFIX TG is supplied in 25 kg. and 5 kg sacks, and 1 kg containers. JAIFIX TG should be stored in clean, cool, dry area protected from direct light as supplied. Original unopened sacks can be stored for 12 months.

The information in this leaflet is based not only on laboratory work but also on practical experience obtained during field work.

All products are sold subject to standard conditions of sale which are available on request.


Technical service:

While new advances and changes will take place one thing will never change is quality and meeting special needs of customer. We are eager to work with you in development of new product and solve your problem.