Krushna Enterprises

3-5/6 digit digital multimeter with non-contact ef-detected

• model km 655 - 15 functions 38 ranges
• model km 656 (trms) - 16 functions 38 ranges

special features :

• fully auto-ranging
• max / min recording mode
• low battery indication
• non-contact ef-detection (ncv)
• probe-contact ef-detection for more precise indication of live.
• line level frequency 40hz to 60khz
• fast measurements, 5/sec
• intelligent auto power off & data hold
• beep-jack input warning against improper a-terminal plug in
• fast audible continuity < 100ms
• diode tester

 

general specifications :

• sensing : average sensing (km 655); trms sensing (km 656)
• basic accuracy : 0. 5%
• display : 3-5/6 digits 6000 counts large easy to read lcd display
• update rate : 5 per second nominal
• operating temperature : -10°c~50°c
• relative hunidity : maximum relative humidity 80% for temperature upto 31°c decreasing
  linearly to 50% r. H. At 50°c
• altitude : operating below 2000m
• temperature coefficient : nominal 0. 15 x (specified accuracy) / °c
  @ (-10°c~18°c or 28°c~50°c), or otherwise specified.
• low battery indication : below approx. 5. 5v.
• power consumption (typical) : 3ma
• apo consumption : 20ma typical except 50ma for a function
• apo timing : idle approx. > 30 minutes
• power supply : standard 9v battery.
• dimension : 173(l) x 83(w) x 48. 5(h)mm
• weight : approx. 300gm.

 

safety :

• safety : the meter is protected, against the users, by double insulation per
  en61010-1, iec61010-1, 2nd ed. , ul61010-1 2nd ed. & can/csa
  c22. 2 no. 61010-1 to “cat iii 1000v & cat iv 600v”.
  terminals (to com) ratings:
  v : category iii 1000 volts ac & dc, and cat iv 600 volts ac & dc
  a : cat iv 600v ac & 500v dc
  over load protection:
  v : 1050v rms, 1450v peak.
  a : 15a/600v, ir 100ka, f fuse
• transient protection : 8kv(1. 2/50ms) lightning surge.
• pollution degree : 2
• e. M. C. : meets en61326(1997, 1998/a1), en61000-4-2(1995) & en61000-4-3(1996)
  in an rf field of 3v/m :
  a) capacitance function is not specified
  b) other function ranges : total accuracy = specified accuracy + 45d
  c) performance above 3v/m is not specified.
• rugged fire retarded double injected casing
• 600v (input protection in all ranges. )
• battery access door with probe holders
• lvd meets en61010-1 cat iii 1kv & cat iv 600v

accessories : test lead pair, battery installed, manual & carrying case

optional accessories :

• current clamp ca300,
• current clamp adaptor ca500, ca1000, ca2000,
• high voltage probe pd-28

500,000 COUNTS AUTORANGING TRUE RMS DIGITAL MULTIMETER WITH VFD FEATURE & PC INTERFACE

Special Features :

• Beep-Jack Audible & Visible Input Warning
• 41 Segment Analog Bar-graph
• Relative Zero Mode
• PC Interface Capability
• VFD-V & VFD-Hz readings
• Crest (Instantaneous Peak Hold) function
• T1-T2 differential Temperature readings
• 500,000 counts stable DCV mode

Features :

• DC Voltage Basic Accuracy 0.02%
• AC; AC+DC True RMS Conversion AC. AC+DC Voltage Bandwidth upto 100kHz (V) & 10kHz (A)
• 5-4/5 Digit 500,000 counts large easy to read LCD Dual display with white Backlight
• Fast Measurements, 5/sec; Fully Auto-Ranging
• Record MAX, MIN & AVG. readings
• MAX & MIN readings & Data Hold Function
• dBm function with 20 selectable values
• High speed Capacitance measurement
• 1000V General Input Protection
• Logic & Line Level Frequency
• Logic Level Duty Cycle Readings & Diode Tester
• Fast Audible Continuity & Diode tester
• Auto Power Off

 

General Specifications :

• Display : 4-4/5 Digits 50,000 counts fast mode. Selectable stable mode 5-4/5 Digits 500,000 counts for DC Voltage & 5 digits 99,999 counts for Hz
• Polarity : Automatic
• Update Rate : 4-4/5 Digits fast mode : 5 per second nominal; 5-4/5 Digits stable mode : 1.25 per second nominal; 41 Segments Bar-graph : 60 per second max
• Sensing : AC, AC+DC True RMS
• Operating Temperature : 0°C to 45°C
• Relative Humidity : Max. 80% R.H. for Temperature up to 31°C decreasing linearly to 50% R.H. at 45°C
• Pollution Degree : 2
• Storage Temperature : -20°C to 60°C, <80% R.H. (with battery removed)
• Altitude : Operating below 2000m
• Temperature Coefficient : nominal 0.15 x ( specified accuracy)/°C @ (0°C ~ 18°C or 28°C ~ 45°C), or otherwise specified
• Power Consumption : 6.5mA typical; 8mA for VFD ranges
• Low Battery : Below approx 7V
• APO Timing : Idle for 17 minutes
• APO Consumption : 70µA typical
• Power Supply : Single 9V battery
• Weight : Approx. 635gm with holster
• Dimension : 208(L) x 103(W) x 64.5(H) mm with holster
• Accessories : Carrying case, One BKP60 banana plug type-K Thermocouple
• Optional Accessories : PC interface kit, Bkb32 banana pins to K-type socket plug adaptor & Magnetic Hanger

 

Safety :

• Double insulation per IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed., & CAN/CSA C22.2 No. 61010.1-0.92 to Category IV 1000V AC & DC
• Transient Protection : 12 kV (1.2/50µs surge)
• Terminals (to COM) Measurement Category : V/A/mAmA : CAT IV 1000V AC & DC
• Overload Protection : mA & mA : 0.44A/1000V, IR 10kA or better, F Fuse A : 11A/1000V, IR 20kA or better, F Fuse V, mV, & Others : 1050Vrms, 1450Vpeak

Additional Information:

• Item Code: KM-869

3¾ DIGITS 4000 COUNTS DUAL LCD DISPLAY DIGITAL CLAMP METER

General Specifications :

Safety Features :

Additional Information:

• Item Code: 2799

3½ digit digital automotive test meter

 

specifications :

 

special features :

•  display : 3½ digits (1999 counts)
• diode test, hfe test, continuity test, data hold, backlight display & duty cycle
• overload protection in all ranges

 

general characteristics :

 

 

Additional Information:

• Item Code: KM-6060

Digit large display digital multimeter with terminal locking system

 

features : low power consumption cmos double integration, a/d transform integrated circuit, auto zero calibration, auto polarity display, data hold, low battery & over range indication.

Additional Information:

• Item Code: KM-6030

AUTO RANGING DIGITAL MULTIMETER WITH TERMINAL PROTECTON SYSTEM

 

FEATURES :

 

 

Additional Information:

• Item Code: 6040

4 Digit 87000 Points Stand-Alone Data-Logging With ON-Screen Recall & Dual Digital Display Digital Multimeter

Features :

• 87000 Stand-alone Data-Logging function (Points at single Display mode)
• 43000 Stand-alone Data-Logging function (Points at Dual Display mode)
• Multiple Data Recording.
• 4 Digit 10,000 counts large easy to read LCD display
• Fast measurements, 5 /sec; Fully Auto-ranging
• Dual Digital display
• 41 segment Analog Bar-graph updates 60/sec
• 0.08% high Basic DCV accuracy
• Optional purchase USB cable & software for Win98/2k/xp/Vista
• Intelligent Auto power off
• Data Hold
• Relative Zero mode
• Audible & Visible Beep jack^TM Input warning against improper plug in
• AC, AC+DC True RMS conversion
• Record Max/Min readings, Auto-ranging
• Crest (Peak Hold) Max/Min readings, Auto-ranging
• Non-contact EF-Detection (NCV)
• Probe-contact EF-Detection for more precise indication of Live
• Autocheck^TM feature (Automatic DCV, ACV & Ohms selection)
• Lo-Z Volts to drain Ghost voltages (Autocheck^TM feature)
• Back-lighted large easy to read LCD display
• DCV 0.01mV to 1000V
• ACV 0.01mV to 1000V
• AC+DCV 0.01mV to 1000V
• DCA 0.1mA to 10A; 20A for 30 seconds per 5 minutes cooling
• ACA 0.1mA to 10A; 20A for 30 seconds per 5 minutes cooling
• AC+DCA 0.1mA to 10A; 20A for 30 seconds per 5 minutes cooling
• Ohms 0.1Ω to 60MΩ
• Conductance 0.01nS to 100nS
• Capacitance 60.00nF to 25mF
• T1 Type-K Temperature readings -50^oC to 1000^oC
• T2 Dual Type-K Temperature readings -50^oC to 1000^oC
• Line Level Frequency 5Hz to 200kHz
• Logic Level Frequency 5Hz to 2MHz
• Logic Level Duty Cycle readings 0.1% to 99.99%
• Diode Tester

 

Safety :

Double insulation per IEC61010-1 2nd Ed.,EN61010-1 2nd Ed., UL61010-1 2nd Ed. & CAN /CSA
C22.2 No. 61010.1-0.92 to Category IV 1000V AC & V DC.

• Transient protection : 12kV (1.2/50µs surge)
• Pollution degree:2
• Measurement Category :CAT IV 1KV.
• E.M.C. : Meets EN61326-1:2006 , EN55022, EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11
• In an RF field of 3V/m:
  
  • Capacitance function is not specified
  • Other function ranges:
  • Total Accuracy = Specified Accuracy + 100 digits
• Overload Protections : 1000VDC and VAC rms
• Rugged fire retarded casing with battery access door
• Replaceable protective holster with probe-holders & Tilt-stand
• Optional purchase magnetic hanger
• 1000V (Ohm, Capacitance & all other Functions) Input protection
• 1000V High Breaking Capacity fuses protected on Current inputs
• LVD meets EN61010-1 CAT IV 1kV

Additional Information:

• Item Code: KM-525

FEATURES :
SPECIFICATIONS :
DC voltage : 0.4/4/40/400/600V ± 0.7%
AC voltage : 4/40/400/600V ± 0.8%
DC current : 40/400mA ± 1.2%, 10A ± 2.0%
AC current : 40/400mA ± 1.5%, 10A ± 3.0%
Resistance : 400/4K/ 40K/400K/4M W
± 1.2%, 40M W ± 2.0%
 Display : 3999 counts, digit is 14mm high
In conformity with IEC 1010 CAT II 1000V
Auto range
Data Hold
 Relative measurement
  Back light
 Auto power off

Capacitance : 4n/40n/400n/4m/40m/
200mF ± 3.0%
Frequency : 10/100/1K/10K/100KHz ± 2.0%
Continuity test
Duty cycle : 0.1% ~ 99.9% ± 3.0%
ELECTRICAL SPECIFICATIONS :
Temperature : -20C ~ 400C ± 3.0% (0.1C),
400C ~ 1000C ± 3.0% (1OC)
Humidity : 30% ~ 95% RH ± 5.0% RH

5 4/5 Digits Hand Held Digital Multimeter 50000 / 500,000 Counts


Features :



Safety :  The meter is protected, against the users, by double insulation per EN61010-1 and
IEC61010-1 2nd Edition (2001) to CAT III 1000V & CAT IV 600V. The meter also meets UL3111-1 (1994)* and CSA C22.2 No. 1010-1-92* to CAT III 1000V.

Category IV safety standard was first released in IEC61010-1 2nd Edition in year 2001, and was yet an UL published standard at the time this catalog was written.

E.M.C. : Meets EN61326(1997, 1998/A1), EN61000-4-2(1995) and EN61000-4-3(1996)

OVERLOAD PROTECTIONS :

• µA & mA: 0.63A/500V, IR 100kA, F fuse
• A :12.5A/500V, IR 10kA, F fuse
• V : 1050 Vrms, 1450 V peak
• mV, & Others : 600 VDC/VAC rms.

TRANSIENT PROTECTION : 8kV lightning surge (1.2/50µs)

Additional Information:

• Item Code: KM-857

4 Digit High Resolution, High Speed & Dual Display Digital Multimeter


Features :

• Digit 10,000 counts large easy to read LCD display
• Fast measurements, 5 /sec; Fully Auto-ranging
• Dual Digital display
• 41 segment Analog Bar-graph updates 60/sec
• 0.08% High Basic DCV accuracy
• Optional purchase USB cable & software for Win98/2k/xp/Vista
• Intelligent Auto power off
• Data HOLD
• Relative Zero mode
• Audible & Visible Beep jack^TM Input warning against Improper plug in
• AC, AC+DC True RMS conversion
• Record Max/Min readings, Auto-ranging
• Crest (Peak Hold) Max/Min readings, Auto-ranging
• Non-Contact EF-Detection (NCV)
• Probe-Contact EF-Detection for more precise indication of live
• Autocheck^TM feature (Automatic DCV, ACV & Ohms selection)
• Lo-Z Volts to drain Ghost voltages (Autocheck^TM feature)
• Back-lighted large easy to read LCD display
• dBm readings, 20 selectable impedance values
• DCV 0.01mV to 1000V
• ACV 0.01mV to 1000V
• AC+DCV 0.01mV to 1000V
• DCA 0.1mA to 10A; 20A for 30 seconds per 5 minutes cooling
• ACA 0.1mA to 10A; 20A for 30 seconds per 5 minutes cooling
• AC+DCA 0.1mA to 10A; 20A for 30 seconds per 5 minutes cooling
• Ohms 0.1Ω to 60MΩ
• Conductance 0.01nS to 100nS
• Capacitance 60.00nF to 25mF
• T1 Type-K Temperature readings - 50^oC to 1000^oC
• T2 Dual Type-K Temperature readings - 50^oC to 1000^oC
• Line Level Frequency 5Hz to 200kHz
• Logic Level Frequency 5Hz to 2MHz
• Logic Level Duty Cycle readings 0.1% to 99.99%
• Diode Tester

 

Safety :

 

• Double insulation per IEC61010-1 2nd Ed.,EN61010-1 2nd Ed., UL61010-1 2nd Ed. & CAN /CSA C22.2 No. 61010.1-0.92 to Category IV 1000V AC & V DC.
• Transient protection : 12kV (1.2/50µs surge)
• Pollution degree:2
• Measurement Catagory :CAT IV 1KV.
• E.M.C. : Meets EN61326-1:2006 (EN55022, EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, En61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11)
• In an RF field of 3V/m:
• Capacitance function is not specified
• Other function ranges:
• Total Accuracy = Specified Accuracy + 100 digits
• Overload Protections : 600VDC and VAC rms

   • Rugged fire retarded casing with battery access door
   • Replaceable protective holster with probe-holders & Tilt-stand
   • Optional purchase magnetic hanger
   • 600V (Ohm, Capacitance & all other Functions) Input protection
   • 600V High Breaking Capacity fuses protected on Current inputs
   • LVD meets EN61010-1 CAT IV 1kV

Additional Information:

• Item Code: KM-829

Digital Multimeter with EF-Detection & Computer Interface (KM 255-KM 257)


Special Features :

• Autocheck V
  
• EF-Detection (NCV)
• Crest Mode (Peak Hold), Data Hold function
• Average Sensing (Model KM 255)
• TRUE RMS (Model KM 257)
• 24 Segments Analog Bar-graph

Features :

• Backlight LCD Display
• Autoranging Relative Zero Mode
• Auto-ranging MAX/MIN record
• Wrong Input (test lead) warning detection (w. r. t. switch position)
• Auto Power Off
• Low Battery Indication
• PC interface (optional)
• Diode & Continuity Test

 

General Specifications :

• Display : 3-5/6 digits 6000 counts LCD display
• Update Rate : Fast Data : 5 per second nominal 24 Segments Analog Bar-graph : 40/second
• Operating Temperature : 0°C to 40°C,at <70% R.H.
• Relative Humidity : Maximum relative humidity 80% for temperature upto 31°C decreasing linearly to 50% relative humidity at 40°C
• Storage Temperature: -20°C to 60°C, <80% R.H. With battery removed from meter
• Altitude : 2000m
• Pollution Degree : 2
• Temperature Coefficient : nominal 0.15 x (specified accuracy)/°C @ (0°C~18°C or 28°C~40°C), or otherwise specified
• Low battery : Below approx. 2.3V
• Power Consumption : 3.5mA
• APO Consumption : 10µA typical
• APO Timing : Idle for 34 minutes
• Power Supply : 1.5V AAA battery x 2
• Dimension : 161(L) X 80(W) X 50(H) mm
• Weight : Approx. 340 gm ( with Holster)

 

Safety :

•  Double insulation per IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed. & CAN/CSA C22.2 No. 61010.1-0.92 to Category II 1000V, CAT III 600V and CAT IV 300V AC & DC
• E. M. C. : Meets EN61326-1:2006 (EN55022, EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11) In an RF field of 3V/m : Capacitance function is not specified. Other function ranges : Total Accuracy = Specified Accuracy + 100 digits (Performance above 3V/m is not specified)
• Transient Protection : 6.5kV lightning surge (1.2/50µs)

 

Accessories : Test leads pair, Carrying Case, Batteries installed, User's Manual & Banana plug K-Type Thermocouple

Optional Accessories : PC interface kit, Magnetic Hanger, Banana plug to K-Type socket plug adaptor

3-5/6 DIGIT DIGITAL TRMS MULTIMETER MOBILE-LOGGER WITH PC INTERFACE
On Screen Date- logging capability 43000 points display with selectable sampling interval 0.05, 1, 20, 40, 60, 120, 240, & 480 seconds

Special Features :

• Data Logging + On screen Data item review
• 52 Segment Bar Graph
• Splash Proof construction
• Auto Leads Resistance Calibration
• Sleep & Log mode to largely extend battery life.
• Logged Max’s & Min’s turning points on screen recall

 

Features :

 

• Basic Accuracy 0.08%
• RS232 PC interface
• Fully Auto-Ranging
• Fast Measurement 5/Sec
• Backlight Display & Data Hold
• Low Battery Indication
• Diode & Continuity Test
• Auto power off

 

Safety :

 

• Double insulation per EN61010-1, UL3111-1,
  CSA C22.2 No.1010-1, & IEC1010-1 CAT III for
  1000V DC & AC, and CAT IV for 600V DC & AC
• Transient Protection : 8 kV (1.2/50μS surge)
• Terminals (to COM) Measurement Category :
  V : Category III 1000V AC & DC &
  CAT IV 600V AC & DC
  A/mAmA: Category III & CAT IV 500V AC &
  300V DC
• Overload Protection :
  mA & mA : 0.63A/500V, IR 200kA , F Fuse
  A : 12.5A/500V, IR 20kA, F Fuse
  V : 1050Vrms, 1450Vpeak
  mV, W & Others : 600V DC / V AC rms
• A input 240V HBC fuse protected
• 600V input protection
• Fire Retarded Case & Protective Holster
• EMC meets EN55022/A1 class B, EN50082-1,
  IEC801-2, & IEC801-3
• LVD meets EN61010-1 CAT II 1kV AC / DC &
  CAT III 600V AC / DC

 

General Specifications :

 

• Sensing : True RMS
  Frequency Bandwidth 20kHz (V) & 1kHz (A)
• Display : 3-4/5 digits 5000 counts LCD display
• Update Rate :
  Digital Data : 5 per second nominal
  52 Segments Bargraph : 60per second nominal
• Low Battery : Below approx. 7V
• Operating Temperature : 0°C to 45°C, 0-80% R.H.;
  35°C to 50°C, 0-70% R.H.
• Storage Temperature : -20°C to 60°C, 80% R.H.
  (With battery removed)
• Temperature Coefficient : nominal 0.15 x (specified
  accuracy)/°C @ (0°C - 18°C or 28°C - 50°C); or
  otherwise specified.
• Apo Timing : Idle for 17 minute
• Power Consumption : 2.7mA typical
• Power Supply : Single alkaline 9V battery
• Dimension : 186(L) X 87(W) X 35.5(H) mm
  198(L) X 97(W) X 55(H)mm with holster
• Weight : Approx.340 gm;
  Approx. 430gm with Holster

 

Accessoreis : Test leads (pair), Holster, Battery installed, User's Manual, Banana plug K-Type Thermocouple

Optional Accessories :

• PC interface Kit, (RS232 optical adapter cable+software CD), Bkb32 banana plugs to K-Type socket plug Adapter
• Model - KM 511 / KM 515
• Current Clamp CA300
• Current Clamp Adaptor CA500, CA1000, CA2000,
• High Voltage Probe PD-28

 

 

 

Additional Information:

• Item Code: KM-515

6,000 COUNTS DUAL DISPLAY DIGITAL MULTIMETER WITH VFD FEATURE

 

Special Features :

• VFD-V & VFD-Hz in Dual Display
• 5msCREST-MAX capture mode (Peak Hold)
• Autoranging Relative -Zero mode
• Display Hold
• EF-Detection (NCV)
• Beep-Jack input warning
• Hz Line Level Frequency
• Hz Logic Level Frequency
• Diode Test
• Continuity Test

GENERAL SPECIFICATIONS :

 

 

• Sensing : Average sensing
• Display : 3-5/6 digits 6000 counts + 3 digits 999 counts dual LCD display
• Update Rate : 5 per second nominal
• Polarity : Automatic
• Low Battery : Below approx 2.4V
• Operating Temperature : 0°C to 40°C
• Relative Humidity : Maximum 80% R. H. For temperature upto 31oC decreasing linearly to
  50% Relative Humidity at 40°C
• Altitude : Operating below 2000m
• Storage Temperature : -20°C to 60°C, < 80% R.H. (With battery removed)
• Temperature Coefficient : nominal 0.15 x (specified accuracy) / °C @ (0°C--18°C or 28°C--40°C),
  or otherwise specified
• Power supply : Standard 1.5V AAA Battery x 2.
• Power Consumption : 5.4mA typical
• APO Timing : Idle for 34 minutes
• APO Consumption : 10µA typical
• Dimension : 186(L) x 87(W) x 35.5(H) mm ; 198(L) x 97(W) x 55.5(H) mm with Holster.
• Weight : Approx. 340 gms; 430gm with holster

 

SAFETY :

 

• Double insulation per IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed., & CAN/CSA C22.2 No.
  61010.1-0.92 to Category II 1000V, CAT III 600V & CAT IV 300V AC & DC.
• Transient Protection : 6kV (1.2/50ms surge)
• Terminals (to COM) Measurement Category :
  V : CAT II 1000V, CAT III 600V & CAT IV 300V AC & DC.
  µAmA : CAT III 500Vac & 300Vdc.
  A : CAT III 600Vac & 300Vdc.
• EMC : Meets EN61326-1:2006 (EN55022, EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3,
  EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11)
  In an RF field of 3V/m :
  Capacitance function is not specified
  Other function ranges : Total Accuracy = Specified Accuracy + 100 dgts
  Performance above 3V/m is not specified.
• Overload Protection :
  µA & mA : 0.63A/500Vac, IR 50kA or better, F Fuse
  A : 10A/600Vac, IR 100kA or better, F Fuse
  V : 1050 Vrms, 1450 Vpeak

 

 

 

ACCESSORIES : Test lead (pair), Holster, Battery installed, User Manual & Carrying case

OPTIONAL ACCESSORIES : Current Clamp CA300, Current Clamp Adaptor CA500, CA1000, CA2000, High Voltage Probe PD-28

 

Additional Information:

• Item Code: KM-711

3 4/5 digit 5000 counts digital multimeter with analog bar graph & rs 232 computer interface

features :



safety : the meter is protected, against the users, by double insulation per iec61010-1 2nd edition (2001) to cat iii 1000v & cat iv 600v. The meter also meets ul3111-1(1994)* and csa c22. 2 no. 1010-1-92* to cat iii 1000v

Additional Information:

• Item Code: 5040

54/5 digits hand held digital multimeter



safety :

the meter is protected, against the users, by double insulation per en61010-1 and iec61010-1 2nd edition (2001) to cat iii 1000v & cat iv 600v. The meter also meets ul3111-1 (1994) * and csa c22. 2 no. 1010-1-92* to cat iii 1000v

Voltage Detector With RCD Load Test & EF Detection

Features :



Safety : Meets EN61243 voltage class B, EN61010-1 and IEC61010-1 2nd Edition (2001) to CAT III 1000V & CAT IV 600V

• Type of Protection : IP65 - water and Dust Resistant.
• Pollution Degree : 2
• Transient Protection : 8kV lightning surge (1.2/50s)
• Measurement Category : CAT III 1000V & CAT IV 600V AC & DC

Additional Information:

• Item Code: KM-69