Labin Scientific Instruments & Calibration Private Limited

LABIN introduces Digital Magnetic Finishing (Polisher) which is very useful for Polishing Casted, Hand Made Filigree and Jewellery WITHOUT ANY METAL LOSS.

The Stainless Steel Media in this highly efficient system burnishes and polishes quickly in working areas such as undercuts recesses and slots with ease. Combined with effective centrifugal force, you will see fast time cycles with highly successful results. Depending upon the size and weight about 100/200 pieces of Rings, Earrings, and Pendant like Jewellery can be excellently polished from Exterior as well as Interior side of within 60-120 minutes. The Time may vary from Carat to Carat of the Gold. Moreover Filigree Items and Interior Side of Ornaments which cannot be polished by other means, which can only be Polished by this Equipment most effectively.

For this evaluation, physical properties of the material under test are determined before aging, and again after aging the test specimen at the specified temperature, for a set duration of time and subsequent cooling to the room temperature before conducting the test again.Determination of effect of aging on various physical properties of different materials may be carried out, by heating the material under test, inside an Oven so that the effects of long term aging are reproduced within a much shorter duration of time.

The updated model of Water / Rain Spray Chamber specially designed to determine suitability of electronic and electrical components driving under rain conditions.

The Equipment is intended to determine Colour Fastness of all types of Textile Materials irrespective of their composition (e. g. Cotton, Linen, Wool, Silk, Man Made Fibers etc.) and their form (e. g. Fabric, Yarn or Fiber etc.) except photo chromatic coloured textile to sunlight.

Labin Colour Matching Cabinet (Light Booth) is a universally preferred choice for visual colour matching and inspection applications. It provides standardized and controlled environment for visual assessment where there is a need to maintain Colour consistency quality. It allows a person to evaluate colour samples under different Light Sources.

The Test is intended for determining the resistance of the colour of Textiles and Leather of all kinds to Rubbing off either Dry or Wet condition and Staining other materials.

The LABIN Exposure Rack is designed to test colour fastness of Textiles Material to daylight. Exposing a set of light fastness standard fabrics 1 to 8 carries out the test and a set of test specimens to daylight till the desire fading of the colour is obtained. The change in colour of exposed area of the test specimen and the light fastness standard fabrics are then examined and the relative degree of colour fastness of test specimen determined.

The Motorised Wrap Reel, with 5 Ruling Positions is suitable for making accurate length of yarn, in hank form for subsequent weighting and determination of count and strength. A Digital Preset Counter is equipped in the Instrument to set the desired numbers of Meter or Yards. The Unit will be supplied with Metric and Imperial System to assists operator for removal of Reeled Hanks. The Automatic Electromagnetic Breaking System in the Equipment that can arrest the Swift in the correct position at the time of desired length of the yarns has been reeled. 5-Station Yarn Package Stand will also be supplied along with.

The updated models of Salt/Cass Fog Test Chamber specially designed for evaluating the corrosion resistance of the surface treatment of metallic materials by Copper Accelerated Acetic Acid Salt Spray Test Method. It consists of following parts : Test Chamber

It consists of Cabinet and Lid and is constructed with insulated double structure made of FRP Moulded Sheet. The upper part (triangular shaped lid made of FRP with acrylic glass window) has sufficient space for the mist to accumulate naturally on it and is so shaped that drops so accumulated do not fall on specimen being tested.

LABIN introduces updated Bench Models and Floor Models of Heavy Duty High Temperature Industrial Oven for Research Laboratories, Production Departments. Ideal for most Aging, Sterilizing, Drying, Curing, Conditioning, Electronics Burn-in, Life Testing and Temperature Applications.

The wearing away of any part of a material by rubbing against another surface is known as Abrasion of that material. There are so many methods for determining the Abrasion Resistance of the fabrics. One of these methods is determination of Abrasion Resistance of the Fabrics by using the Martindale Abrasion Tester. The Abrasion Resistance is measured by subjecting the specimen to rubbing motion in the form of a geometric figure, that is a straight line, which becomes a gradually widening ellipse. Until it forms another straight lines in the opposite direction and traces the same figure again under known conditions of pressure and abrasive action.

Pilling is the formation on the surface of a fabric of small balls of entangled fiber. It is a fabric surface fault characterized by little pills of entangled fibers clinging to the surface. These are formed during wearing or washing by the entanglement of the loose fibers, which protrude from the fabric surface, and development of these into spherical bundle anchored to the fabric by a few unbroken fibers. These give a very unsightly look to the garments.

The Yarn Strength Tester made of two yarn grips. The upper grip is mounted on the Spring Balance type load measuring arrangement. The lower grip is attached to the up and down moving arrangement the lower grip is made by means of screw/nut with guide rods, bearing gear box and a hand wheel the instrument is operate manually. There is a Dummy Pointer attaches to the spring balance the spring balance assembly and screw assembly attached to a rigid vertical stand. The stand attached to the fabricated base.

It is used for Pure, Pyrogen Free Distilled Water. All stainless steel body. It comprises of Main Chamber, Condenser Tube, Condenser Jacket, Vapour Baffle and Constant Level Arrangement. Splashing of Water Delivery Tube is avoided by superior design of Vapour Baffle. The Lid rests ensures minimum (negligible) loss of steam. The Still is provided with Bracket for fixing on wall on which the Still can rest.

This mixer has been designed particularly for Laboratory Work where small quantities of material are being tested. The Mixer works very efficiently with material upto a maximum of 20-mm size either in a wet or dry state. The mechanical action is positive and rapid as the Blades are design to mix the Contents of the pan. Driving Power direct through an enclosed-geared reduction unit, with wearing parts tipped with Manganese wherever possible to minimize maintenance. The Steel Stand and Chases supports the Pivoted Head carrying the Blades. These may be adjusted for depth depending on the size of material to be mixed. The Rotating Blade Assembly runs in a select Ball-Bearing Housing. Supplied complete with Mild Steel Pan and Carrying Handle.

• Designed for desiccation, vacuum embedding, plating, process control, and inert atmosphere applications.
• Radiant warm wall heaters mounted outside of chamber to conserve chamber-working space and eliminate the hazards of open wire heaters.
• 3 (7.6 cm) glass wool insulation minimizes heat loss from chamber.
• Two piece stainless steel shelf systems improve heat conduction to samples and are easily removed for cleaning.
• Corrosion-resistant # 304 stainless steel interior.
• Tempered glass window in door allows viewing of samples.

Temperature can not be measured entirely without error, so it is necessary to quantify these errors by calibration of the probe, with or without its associated display against the reference standard in the respective temperature range. Calibration is essential where traceability to a National Standard or International Standard in compliance to industrial requirement in ISO-9000 specification.

Labin Temperature Heating/Water/Cooling/Clinical Baths may be used for temperature application like Calibration Measurement and Comparison of the Thermometers and Associate Instruments in the given range -20 C to 300 C. An electronic proportional band control adapts the heat supplied to the bath for thermal stability and uniformity requirements of the Bath for Comparison/Calibration.

LABIN Box Furnace is the choice of Research and Development Laboratories that need a reliable, Energy-efficient, Accurate and Automatic Furnaces for a wide range of applications such as ash determination, heat treating, fusions, glass and enamel tests, drying precipitates etc.

The Tearing Strength of Fabrics, Plastic Films or other similar material is determined by measurement of the work done in tearing through a fixed length of the test specimen using the Labin Tearing Strength Tester.