|
Products & Services
|
Hydraulic and Pneumatic Equipments |
|
|
We offer range of hydraulic and pneumatic equipments such as Tube Fittings, Pneumatic Pump, Manifold & Metering Cartridge,Electronic Timers & Controllers, Pump and Motor Pump Assembly,Pneumatic Pumps,Pneumatic Tools, Manual Grease Pumps For Single and Dual Line Systems, Oil Circulation System.
|
We are engaged in offering a wide range of tube fittings that are manufactured using high grade material such as brass, steel etc. manufactured using superior quality material these fittings are widely appreciated for their sturdy and tight integral line system. Further, to meet the technical requirements of our clients, we design these fittings in various customized sizes and patterns. Following are the fittings available for 4mm OD tube: | Models | Description | | F-E-4T | Elbow M8 x 1 Or 1/8" BSP | | F-B-4 | Banjo M8 x 1 Or 1/8" | | F-E-B-4 | Elbow block | | F-SC-4T | Straight connector M8 x1 Or 1/8" BSP | | F-C-4 | Connector block | | F-CR-4 | Cross block |
Following are the fittings available for 6mm OD tube:
| Models | Description | | F-E-6T | Elbow Male thread 1/8" thread 1/8" BSP to right angle | | F-B-6 | Banjo Male thread 1/8" BSP to right angle | | F-E-B-6 | Elbow block for joining two tubes of right angle | | F-SC-6T | Straight connector 1/8" BSP or M8 x 1 to connect 6mm tube of end point | | F-T-6 | Tee block for dividing main line into two lines | | F-C-6 | Connector block for joining two tube | | F-CR-6 | Cross block dividing main line into three lines | |
|
Send Enquiry
| Our Pneumatic Pumps are sturdy and compact in design & perform most complexed job in a simple manner. They require less changeover time & are easy to clean & maintain. These pumps are specifically designed for transferring cream from storage vessel to the hopper of tube filling machine. Renowned for their hassle free and long lasting functioning, these are available with us at cost effective price. We manufacture Pneumatic Pumps which are highly durable as well as reliable. These grease pumps are designed according to the technical specifications provided by the client. Our pumps are also corrosion resistant and require less maintenance.
APPLICATION: The pneumatic grease pump is suitable for dispensing of grease and automatic feeding of grease to bearing and other moving parts of machines. Such as milling machine rolling machine, presses and hammers, Rubber processing machine, die casting machine, furnaces etc. The pump is suitable for grease upto NLG-2. For distribution we used progressive blocks through this pump.
WORKING: Pneumatic grease pump are operated through pneumatic line, connected to the ports of pneumatic cylinder. The cylinder is built in with the pump housing. Druign on period of the pneumatic line a piston inside the cylinder is pushed ejecting out grease from the outlet port of the pump housing. During the reverse flow of pneumatic line grease is sucked through the suction port. In the pump spring force through follower plate exerted on the top surface of the grease make the suction of the grease positive and easier. Pneumatic pump is available in adjustable discharge and multi port with adjustable discharge in each port. Discharge and reservoir of pump is available as per customer requirement.
AIR REMOVING: For air removing, un screw the bleed plug apply compressed air and press the grease pusher by knob till grease come out from bleed port and plug the bleed port. The pump is ready for peration.
CONSTRUCTION: There is a reservoir mounted on the pump body for storage of grease. A tell tale rod connected for sensing grease level.
Check valves is fitted on the outlet port of the pump to stop reverse flow of grease into the pump through
outlet port. To bleed air entrapped in the system, there is a plug on the pump body which is to be opened
fill continuous flow of grease starts coming.
The adjusting screw is provided in order to vary in output of the grease by tightening the screw the output
of grease decreases and vice versa.
It is must to put filter regulator unit in the pneumatic line fed to the pump. This will ensure that pneumatic
line going to the pump is dust and moisture free.
FILLING: Grease filling in the reservoir can be done manually as well as with the help of other pump. For these who wants to fill grease by another pump, a 1/4" BSP ports is provide on front side of the pump. This port is ormally plugged. |
Send Enquiry Manifold & Metering Cartridge
Our versatile range of pumps and controllers include highly functional manifold and metering cartridges. These cartridges are designed and manufactured in various designs to meet the specific requirements of our clients. Further, to ensure their durability and reliability these cartridges are checked at regular intervals. Following are the models and descriptions of manifold cartridges: | Models | Description | | M-1 | One way (for single D1/D2 Metering Contridge) | | M-2 | Two way (for two D1/D2 Metering Cartridges) | | M-3 | Three way (for three D1/D2 Metering Cartridges) | | M-4 | Four way (for four D1/D2) Metering Cartridges) | | M-5 | Five way (for five D1/D2) Metering Cartridges) | | M-6 | Six way (for six D1/D2 Metering Cartridges) | | M-8 | Eight way (for Eight D1/D2 Metering Cartridges) | | M-1A | One way (for single D3 Metering Cartridge) | | M-2A | Two way (for two D3 Metering Cartridges) | | M-3A | Three way (for three D3 Metering Cartridges) | | M-4A | Four way (for four D3 Metering Cartridges) |
Following are the models and descriptions of metering cartridges:
| Models | Dosages | | D-1 | 0.01/0.03/0.05, 0.10/0.16 cc per cycle | | D-2 | 0.25/0.40 cc Per cycle | | D-3 | 1.0/1.6 c cc Per Cycle | |
|
Send Enquiry Electronic Timers & Controllers
| With the help of latest technology and advanced techniques, we are able to manufacture a wide range of electronic timers and controllers. These controllers are used in those lubrication systems where pressure switch and float switch are provided for sensing the pressure load as well as the low oil level. Further, these lubrication systems have on time of 5 sec as well as an adjustable fixed and off time between 2 to 240 min. Following are the models and descriptions of electronic timers offered by us: | Models | Description | | ET-5-30 | | | ET-60-240 | | | ET-2-30/2-60 | |
Following are the models and descriptions of electronic controller offered by us:
| Models | Description | | ECW2-240 | -
Wall mounting -
ON time-5 sec. (fixed) -
OFF time 2, 4, 8, 15, 30, 60, 120 -
240 min. (Adjustable) with lubrication -
Fault & low oil level sensing | | ECP-240 | -
Panel mounting -
ON time-5 sec. (fixed) -
OFF time 2, 4, 8, 15, 30, 60, 120, -
240mm (Adjustable) with lubrication -
Fault & low oil level sensing | | ECP 2-240 C | | |
Send Enquiry
At par with the technical requirements of our clients, we manufacture a highly durable range of pneumatic pumps. These pumps are suitable for dispensing grease and automatic feeding of grease to bearing and other moving parts of machines. Being suitable for greasing up to NLG-2, these pumps greases machines such as milling machine rolling machine, presses and hammers, rubber processing machine, die casting machine, furnaces etc. Working: Pneumatic grease pump are operated through pneumatic line, connected to the ports of pneumatic cylinder. The cylinder is built in with the pump housing. During on period of the pneumatic line a piston inside the cylinder is pushed, ejecting out grease from the outlet port of the pump housing. During the reverse flow of pneumatic line grease is sucked through the suction port. In the pump spring force through follower plate exerted on the top surface of the grease make the suction of the grease positive and easier. Pneumatic pump is available in adjustable discharge and multi port with adjustable discharge in each port. Discharge and reservoir of pump is available as per customer requirement.
Air removing: For air removing, un screw the bleed plug apply compressed air and press the grease pusher by knob till grease come out from bleed port and plug the bleed port. The pump is ready for operation.
Construction: There is a reservoir mounted on the pump body for storage of grease and a tell tale rod is connected for sensing grease level. -
Check valves is fitted on the outlet port of the pump to stop reverse flow of grease into the pump through outlet port. -
To bleed air entrapped in the system, there is a plug on the pump body which is to be opened fill continuous flow of grease starts coming. -
The adjusting screw is provided in order to vary in output of the grease by tightening the screw the output of grease decreases and vice versa. -
It is must to put filter regulator unit in the pneumatic line fed to the pump. This will ensure that pneumatic line going to the pump is dust and moisture free. Filling: Grease filling in the reservoir can be done manually as well as with the help of other pump. For these who wants to fill grease by another pump, a 1/4" BSP ports is provide on front side of the pump. This port is normally plugged. |
|
Send Enquiry
| We are one of the leading suppliers and stockiest of hydraulic & pneumatic tools and accessories that is widely used for maintenance of machineries in various industries for water, oil, steam, air and chemicals. We make sure that our original manufacturers the range of hydraulic & pneumatic tools fittings in CS, SS and Brass as per the drawings or samples. All our items are available from the ex-stock. |
Send Enquiry Manual Grease Pumps For Single and Dual Line Systems
Used in various industries, our Manual grease pumps are widely known for their compact size and rigid construction. The pump is specially designed with minimum moving parts so as to make it long lasting and absolutely trouble free operation. Further, it comprises physical aspects such as: - Minimum maintenance
- Easy to Operate
- Energy saving
APPLICATION: This pump meant for feeding grease to bearing and other moving part of machines and other lightly machines having 1 to 20 lubrication point. WORKING: On pulling the handle of pump, grease are sucked through suction port on pushing handle of pumpt grease comes out under pressure through check value. Spring pressure through follower plate exerted over the top surface of the grease further helps to push the grease in suction port. EQUIPMENT: Pump is made up of purely transparent acrylic reservoir for storage of grease. For sensing the Grease level a tell tale rod is provide and follower plate assembly for help in positive suction of grease. It contains two outlet part of 1/4" BSP right and left side in which one is used as air bleed valve and second port used as a outlet. To check reverse flow of grease, a non return valve is provide in the system of the outlet port. FILLING OF GREASE: Grease can be filled manually or with another pump. Filling from pump 1/4: part is provide. Manually, we have to remove follower plate, spring, top cover and fill the grease from the top of the reservoir and to fit all the components by pressure. For air removing unscrew the bleed plug put the handle maximum out and press the follower plate by knob till grease comes out from bleed plug. DISTRIBUTION SYSTEM: A Progressive block is used to distribute the grease to the available lubrication points in sequence one after another, Progressive Blocks are added as per requirement. | Models | Reservoir Capacity | Discharge | Maximum Pressure | Vertical Wall Mounting | | MGP - 500 - 3 | .5 kg. | 3cc Per Stroke | 70 kg./cm2 | 4 Holes, 7 Dia. | | MGP - 1000 – 4 | 1 kg | 4cc Per Stroke | 100 kg./cm2 | 4 Holes, 7 Dia. | | MGP - 1500 – 6 | 1.5 kg | 6cc Per Stroke | 120 kg./cm2 | 4 Holes, 9 Dia. | |
|
Send Enquiry
| We are engaged in manufacturing and supplying a wide range of oil circulation systems that caters to the needs of paper industry, steel plant, sugar plant etc. in these systems, oil is sucked from reservoir with the help of pump and ejected on lubrication point. Through filter and cooler, oil is returned in the reservoir by retuning line. Before pushing the oil again it should be clean with normal temperature.
APPLICATION: LUBCON introduce O.C.S. (oil circulating system) which is best suited for paper industry, steel plant, sugar plant etc. CONSTRUCTION: In O.C.S. We use the gear pump / screw pump discharge upto 600 LPM driven by electric motor. Pump is connected with reservoir. Reservoir capacity is depend on pump discharge. In line filter, cooler and other control with the gauge fitted by standard tubing and fitting on skid. WORKING: In O.C.S. Oil is sucked from reservoir with the help of pump and ejected on lubrication point. Through filter and cooler, oil is returned in the reservoir by retuning line. Before pushing the oil again it should be clean We use the gear pump and screw pump discharge up to 600 LPM driven by electric motor. Pump is connected with reservoir. Reservoir capacity is depend on pump discharge. In line filter, cooler and other control with the gauge fitted by standard tubing and fitting on skid. - Oil tank
- Gate valve
- Y-type strainer
- Pump
- Coupling
- Motor
- Pr gauge
- Pr. relief valve
- Check valve
- Pr. switch
- Filter
- Temperature gauge
- Oil cooler
- Header
- Ball valve
- High oil level switch
- Low oil level switch
- Needle valve
- Gate valve
- Oil level gauge
- Manifold
|
Send Enquiry
|
© Lubcon Engineers. All Rights Reserved (Terms of Use)