Max-ion Engineering ServicesMax-ion Engineering Services

Water Treatment Plant

Share: Facebook Twitter Stumbleupon

We are specialized in the manufacture and supply of a wide range of Water Treatment Plant in the market. Our range of Industrial Water Treatment Plant comprise of Reverse Osmosis Filtration Plant, Demineralisation Plant, Mineral Water Plant, Water Softener System, Filtration Plant and so on.


Filtration Plant
Enlarge View

Filtration Plant

We manufacture high quality Industrial Filtration Plant in the marketplace. We offer both the standardized & custom built pressure Croton Filtration Plant. It is used for the removal of removal of suspended solids from water with either Dual Media filteror a complete line of single media filters including sand, activated carbon, anthracite, etc. Additionally, we are one of the reputed Montebello Filtration Plant Manufacturers and Exporters from India.



Water Softner
Enlarge View

Water Softner

We are one of the trusted Wholesale Industrial Water Softener Suppliers in India. Water Softener System is used to remove hardness of water. The process of removing hardness imparting Ca++ & Mg++ ions from water is called "Softening process" Its basically a resin technology in which bi-functional group attached to co-polymer resin which plays a vital role in exchanging process of Ca++ & Mg++ ion by Na++ion. Regeneration of cation resin is done by NaCL solution required after each designed O.B.R Cycle of system. Water softener is used in all chemical industries, Boiler Feed Water, Pharmaceutical Industries, Induction Furnace Application, Heat Exchanger Application, Regeneration System, and Domestic Application. Besides, we are also one of the foremost Magnetic Water Softener Manufacturers.



Demineralisation Plant / Dm Plant / Deioniser
Enlarge View

Demineralisation Plant / Dm Plant / Deioniser

MAX-ION Industrial two bed demineraliser (Deionizers) Type CATION and ANION are available in a wide range range with maximum flow rate from 100 LPH to 200000 LPH.

Application
:

  • Pharmaceutical  Industry and storage batteries
  • Process water for manufacturing plants
  • Boiler feed water and electronic industries
  • Beverage and food processing industry
  • Hospital,hotel,Institute and more

Demineralization or Deionization is the process of removing mineral salts from water by using the ion exchange process.  With most natural water sources it is possible to use Demineralization and produce water of a higher quality than conventional distillation.

Fluid Systems Manufacture a Wide range of custom-built softening, Dematerializing plants for industrial process water applications, with inherent design to conserve water, and save costs. They are available in different sizes and materials, manually operated or fully Automatic, & ready to install & are available as standard models or custom built versions for specific needs.

Operating Principle
 
A Typical two-bed DM Plant consists of two FRP/MS Rubber lined Pressure vessels connected in series along with its internal fittings. The first unit consists of high capacity strongly acidic cation exchange resin, which converts positive ions of salt and replaces them with hydrogen ions to form respective acids, which are absorbed in next vessel by strongly basic anion exchange resin. The water obtained by this process shows conductivity less than 20 µ S / cm at 25o C and total dissolved solids less than 10 ppm.

Further high purity water can be achieved by Mixed Bed Deionisers, which are designed to produce high purity treated water. They can be used as polishing units after two bed DM Plant to obtain high purity water. Mixed Bed Deionisers are single column units, filled with strongly acidic cation and strongly basic anion exchange resins mixed together.

There are four distinct stages in the operation of Deionisers

  • Service
  • Backwashing
  • Regeneration
  • Rinse/remix


Service

In the Service cycle the water enters the vessel and passes through the Resin bed of the respective exchanger

Backwashing           
 
After the resins are exhausted, the bed is backwashed. Backwashing is carried out by a uniform upward flow of water through the resin bed. The backwash step expands the resin bed releasing any entrapped particulate matter & removes the channeling in the resin column if occurred during the service cycle.
           
Regeneration          
 
When the ion exchange resins loose all the exchangeable ions, they require regeneration to restore them back to hydrogen or hydroxyl form depending upon whether they are cation or anion resins. To achieve this 4 - 5% concentrated solution of Hydrochloric acid is used for cation resin and a 4% - 5% concentrated solution of caustic soda for anion resin. Sulphuric acid can also be used for Cation Regeneration but the concentration of acid during injection must be kept at minimum, such as to prevent calcium sulphate precipitation on the resin.
 
Rinse
 
The final stage of regeneration is to rinse the resins of excess regenerant
 
Advantages
 

I. Easy to install & operate

II.Complete Assembly with backwash ®eneration equipment

III.Produces DM water of high purity









Contact Us

Max-ion Engineering Services
Mr. Sunil Kumar Singh (CEO)
S-179, Yashoda Nagar, Near Pouja Guest House, Near Shanti Medical Store, P.O. Kidwai Nagar
Kanpur - 208011, Uttar Pradesh, India

Contact via E-mail


Home|About Us|Our Products|Site Navigation|Contact Us
Member IndiaMART.com © Max-ion Engineering Services. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited