Release Coating For Polyurethane

Capitalizing on our latest technological advancements, we offer a comprehensive range of Release Coating for Polyurethane MAC- 715. These non stainable semi-permanent release coatings are used for molded polyurethane parts. As these can be easily applied our range of     mould release coatings are used with cast urethane, foams, integral skin as well as polyester and epoxy material. As per the requirements of our clients, we offer MAC-715 in 1 liter, 3.5 liters and 20 liters containers.

How to use

• Should be applied to a clean and dry surface
• A thin even film is sprayed over the entire surface to be coated and is left for certain time period to dry
• If required the film is applied again for fine coating
• The solvent used in the manufacturing of MAC 715 is flammable, so these should be stored in highly ventilated area
• Keep away from heat, sparks and flame

 

Properties:

• Fast air cure
• Improved part appearance
• Easy to apply
• No build up
• Non staining
• No migration
• Non staining

Our organization holds expertise in offering a wide range of Release Coating for Polyurethane- MA 8500 A. These are formulated as per the set industry standards to be used on the molded polyurethane parts. Release Coating also provide fast and easy part removal with no transfer and multiple release cycles per application. Further, these mould release coating can be easily applied on various molds viz, cast urethane, foams, integral skin as well as polyester and epoxy material. Our range of Release Coating is available in the packaging of 5 liters and 20 liters containers.

 

How to use

 

• A fine film of MA 8500 should be sprayed on the clean and dried mold
• Before the application of the second coat the mold should be properly dried so that the solvents get evaporated
• Although the ingredients are non toxic but standard industrial practices should be employed while applying these coats
• Contact to eyes should be avoided to avoid any hazardous effects

 

Properties:

 

• Easy to use and fast air cure
• No migration
• Improved part appearance
• Reduced rejection
• Non-staining
• No build-up

With the assistance of our proficient team, we are involved in offering a wide range of Release Coating for Polyurethane. These non toxic release coatings are widely used for molded polyurethane parts. Our range of release coating provides fast and easy removal of molded polyurethane parts. Further, these can be comfortably applied on cast urethane, foams, and integral skin products for better results. We offer our products in different packaging options ranging from 5 liters and 20 liters containers.

How to use

• The release coating should be diluted with toluene, hexane or heptane in the ratio of 1:5.
• After dilution a thin film should be sprayed over the clean mold and the surface should be left for drying
• Baking of the mold is not required
• For maximum durability freezing of the products should be avoided

 

Properties:

• Fast air cure
• No migration
• Improved part appearance
• Reduced rejection
• Non-staining
• No build-up

PRODUCT DESCRIPTION

MAC 716 is a production proven semi-permanent release coating for moulded polyurethane parts. It provides, fast, easy part removal with no transfer and multiple release cycles per application. The product is suitable for use with cast urethane, foams. Integral ssin as well as polyester and epoxy materials.

 

TYPICAL PRODUCT DATA

Color and Appearance.............. White Emulsion

Dispersing medium................... Water

Specific Gravity......................... 1.00

 

KEY PERFORMANCE PROPERTIES

• Easy to apply

• Fast air cure

• No migration

• Improved part appearance

• Reduced rejection

• Non-staining

• No build-up

 

USES

Highly recommended for polyurethane parts, urethane foam, close cell, Integral skins, urethane elastomers, and epoxy.

 

METHOD OF APPLICATION

MAC 716 should be applied to a dean, dry surface. All previous used release coatings should be removed by an appropriate method. Spray a thin, even film over the entire surface to be coated and allow to dry. Re-apply as required. No baking necessary.

 

 

 

 

 

 

 

 

 

Solvent Based Semi Permanent Release Coating For Polyurethanes & Epoxy

Product Description

MAC 715 is a production proven semi-permanent release coating for moulded polyurethane & Epoxy parts. It provides, fast, easy part removal with no transfer and multiple release cycles per application. The product is suitable for use with cast urethane, foams. Integral skin as well as polyester and epoxy materials.

 

Typical Product Data

Color and Appearance.............. Clear solution

Dispersing medium................... Heptane

Specific Gravity......................... 0.706

 

 

Key Performance Properties

• Easy to apply

• Fast air cure

• No migration

• Improved part appearance

• Reduced rejection

• Non-staining

• No build-up

 

Uses

Highly recommended for polyurethane parts, urethane foam, close cell, Integral skins, urethane elastomers, and cast epoxy applications.

 

Method Of Application

MAC 715 should be applied to a dean, dry surface. All previous used release coatings should be removed by an appropriate method. Spray a thin, even film over the entire surface to be coated and allow to dry. Re-apply as required. No baking necessary.