This affordable single-channel 4Gb/s host bus adapter offers twice the performance of 2Gb/s Fibre Channel at a small premium. The 4Gb/s Fibre Channel PCI Express adapter series was created to fulfill virtually any storage connection need or environment, whether data mining, video and media streaming, or providing high availability. LSI adapters support end-to-end error detection (cycle redundancy check or CRC) for improved data integrity when reading or writing disks. Since the LSI7104EP-LC is fully compatible with 1 and 2Gb/s legacy products, you are assured of investment protection. This HBA provides unsurpassed performance for your data-intensive and high-bandwidth applications, while utilizing the Fusion-MPT™ architecture to accelerate time to market.
This affordable dual channel 4Gb/s host bus adapter offers twice the performance of 2Gb/s at a small premium. The 4Gb/s Fibre Channel PCI Express adapter series was created to fulfill virtually any storage connection need or environment, whether data mining, video and media streaming, or providing high availability. All LSI adapters support end-to-end error detection (cycle redundancy check or CRC) for improved data integrity when reading or writing disks. Since the LSI7204EP-LC is fully compatible with 1 and 2 Gb/s legacy products, you are assured of investment protection. This HBA provides unsurpassed performance for your data-intensive and high-bandwidth applications, while utilizing Fusion-MPT™ architecture to accelerate time to market
This affordable single channel, 4Gb/s host bus adapter offers twice the performance of 2Gb/s at a small premium. Since the LSI7104XP-LC is fully compatible with 1 and 2 Gb/s legacy products, you are assured of investment protection. You can attain unsurpassed performance for your data-intensive and high-bandwidth applications, while utilizing Fusion-MPT™ architecture to accelerate time to market.
Enables iSCSI-based servers to access Fibre Channel disk or tape storage. Two 2Gb Fibre Channel ports, two 1Gb iSCSI ports, ½U wide, single power supply
Enables SAN island connectivity over GbE when used in pairs. SmartWrite™ improves asynchronous replication performance. Two 2Gb Fibre Channel ports, two 1Gb iSCSI ports, ½U wide, single power supply
The 1-Gigabit Ethernet Pass-through Module (part ID SBM-GEM-002) is a non-configurable pass through module that includes fourteen 1-Gb/s external uplink (RJ45) ports and fourteen internal 1-Gb/s downlink ports for the SuperBlade®'s LAN interfaces. This module also has two internal Ethernet paths to the CMM(s) for viewing module temperature and voltage (but not for configuration since all connections are fixed).
The 10-Gigabit Ethernet Pass-through Module (part ID SBM-XEM-002) is also a non-configurable pass through module. It provides fourteen 10-Gb/s external uplink (SFP+) ports and fourteen internal 10-Gb/s downlink ports for the SuperBlade®'s LAN interfaces. Internal links are provided by the use of a mezzanine card (AOC-IBH-003) with 10-Gigabit Ethernet support capability (see AOC-IBH-003 item description below).
The LSI SAS 9200-16e host bus adapter enables large-scale storage arrays through 16 high-speed 6Gb/s ports, supporting up to 1024 SATA and SAS physical devices. This HBA bolsters large capacity external server storage RAID and non-RAID enclosures by pairing an x8 PCI Express 2.0 host interface with four external x4 SFF8088 Mini-SAS connectors. LSI SATA+SAS HBAs are compatible with 6Gb/s and 3GBb/s, SATA and SAS, hard disk drives, solid state drives, and tape drives. The LSI SAS 9200-16e doubles the performance of previous generation SATA+SAS HBAs and is great for driving cost-effective and reliable scalability in today’s data centers.
The LSI SAS 9200-8e host bus adapter enables large-scale storage arrays through eight high-speed 6Gb/s ports, supporting up to 512 SATA and SAS physical devices. This HBA bolsters large capacity external server storage RAID and non-RAID enclosures by pairing an x8 PCI Express 2.0 host interface with two external x4 SFF8088 Mini-SAS connectors. LSI SATA+SAS HBAs are compatible with 6Gb/s and 3GBb/s, SATA and SAS, hard disk drives, solid state drives, and tape drives. The LSI SAS 9200-8e doubles the performance of previous generation SATA+SAS HBAs and is great for driving cost-effective and reliable scalability in today’s data centers
The LSI SAS3801E card enables large-scale direct attach storage (DAS) arrays through eight external 3Gb/s ports, driving up to 122 SAS and SATA devices. The host bus adapter drives external server storage RAID and non-RAID enclosures with unprecedented throughput by connecting an eight-lane 2.5 Gb/s PCI Express bus with two external x4 SFF8088 miniSAS connectors. This SAS/SATA low-profile adapter is perfect for 1U/2U servers, driving 4800 MB/s full-duplex externally.
The InfiniBand Switch Module (part ID SBM-IBS-001) is a switch-based, point-to-point bi-directional serial link system. It provides high-speed interconnectivity among the blade modules and to external InfiiniBand peripherals. The InfiniBand switch supports 4X DDR connections (20-Gbps).
For any blade to access the InfiniBand module, it must have an InfiniBand mezzanine HCA card installed on its mainboard. The AOC-IBH-002, AOC-IBH-XDD and AOC-IBH-XDS mezzanine cards provide this 20-Gbps connectivity (4x DDR) through the backplane to the InfiniBand switch module. The AOC-IBH-003 and AOC-IBH-XDD can alternatively be used for 10-Gbps Ethernet connectivity when used in concert with the SBM-XEM-002 10-Gbps Pass-through module.
The SuperBlade™ chassis management module (CMM) provides total remote control of individual server blades, power supplies, cooling fans, and networking switches remotely. System administrators enjoy the management ease and reassurance of continuous onboard instrumentation monitoring (temperature sensors, power status, voltages and fan speed). Remote power control capabilities to reboot and/or reset the server are available as well as remote access to the BIOS configuration and operating system console information vial SOL (Serial over LAN) or embedded KVM capabilities. Because the controller is a separate processor, all monitoring and control functions operate flawlessly regardless of CPU operation or system power-on status.
One of the biggest benefits of moving to a blade environment is the relocation of power supplies and fans into a single chassis versus an individual set in each server. This greatly helps reduce the power requirements on a per server basis.
Underlining Supermicro's high-efficiency power philosophy into the SuperBlade™ server technology, Supermicro engineers have mastered the power supply design challenge to produce high-quality, high-performance solutions with peak efficiency ratings of 90% or higher. Supermicro solutions continue to outperform and outlast the competition and providing the best technology investment available to customers.
Availability - Non-stop power with 3+1 redundant power supply modules
Cost Saving - At 90%+ peak efficiency, power consumption is significantly reduced, providing a planet-friendly, real-world advantage for our environment.
Investment Protection - Power capacity headroom for future generation processors
Easy Installation - Snap-in installation from the back of the chassis; hot-swappable in operation
Intelligent Power Infrastructure - Each power enclosure includes a power management module that monitors the power supplies and the power enclosure that connects to the blade management.
On-board I/O RISC processor and RAID offload provides true hardware RAID. - SCSI device driver model to take advantage of the benefits of SCSI using inexpensive Serial ATA drives .
Bootable array support for greater fault tolerance.
Variable stripe size for performance tuning by application.
64-bit LBA support.
ATA pass-through mode support.
Up to 512MB DDR2 533 memory with ECC protection. (see table below)
32 pooled DMA channels.
Complete configuration management suite. - 3ware BIOS Manager 2 (3BM2) - easy to use BIOS configuration tool. - 3ware Disk Manager 2 (3DM®2) - browser-based management tool. - Command Line Interface (CLI) - scriptable configuration tool.
SNMP support.
SMTP support for email/pager notification.
ATA/6 and Out of band (OOB) staggered drive spin-up support.
Auto carving allows LUNs > 2TB to be divided into multiple units for legacy operating systems limited to 2TB max. per LUN.
Battery Backup Unit (BBU) support.
Multiple logical unit sizes and RAID levels on one card.
Multiple card support within a system for large storage requirements.
Hot-swap and hot-spare support for data availability.
Dynamic sector repair for robust data protection.
S.M.A.R.T. disk drive monitoring for reliability.
Emergency Flash Recovery protects against failed firmware upgrade.
Drive activity LED support.
Online Capacity Expansion and RAID Level Migration.
Enhanced data protection with write journaling for non-redundant arrays and accidental drive removal.
Drive insertion and removal notification.
Array/Drive Status and drive identification LED support. (requires 3ware Chassis Control Unit-enabled backplane)
Chassis Control Unit for enclosure management via I2C.
Housed within a 19" industry-standard rack, SuperBlade® servers reduce server footprint in the data center. Power, cooling and networking devices are aggregated in the rear of the chassis which optimizes the required amount of space.
Up to ten blade servers can be installed in a 7U chassis. Compared to the 10U of rack space that ten 1U servers would normally require as individual servers, the SuperBlade provides about 50% density savings with 60 servers and 24 switches in a 42U rack..
The SuperBlade® server chassis enclosure greatly simplifies the cabling process by aggregating cabling of ten servers at once. Up to 90% of network, power, and KVM cabling required for ten 1U servers are reduced by moving to blade servers in a single chassis. These cabling reductions continue across networking, SAN connectivity, and management controllers.
Reducing the number of cables speeds up the deployment of servers and helps reduce troubleshooting issues by presenting fewer physical connections to the server
Fibre channel switches from the largest enterprise datacenter to the smallest home business, qlogic offers san connectivity to meet the needs of any it environment. Each sanbox san switch comes pre-loaded with all the management tools required to easily connect servers to storage, maximizing the return on both your server and storage investments.
The 1-Gigabit Ethernet switch module (part ID SBM-GEM-001) includes ten external 1-Gb/s uplink (RJ45) ports and fourteen internal 1-Gb/s downlink ports for connection to the SuperBlade®'s LAN interfaces. This layer 2 Ethernet switching module also has two internal Ethernet paths to the SuperBlade® Chassis Management Module CMM(s) to allow configuration, management, and control of the switch and its ports through a browser-based management interface. Offering such advanced features as link aggregation (static), VLAN support, and Jumbo Frame support, the switch provides a connection between the Ethernet controller integrated on the mainboard and external Ethernet systems.
The 1/10-Gigabit Ethernet layer 2/3 Switch module (part ID SBM-GEM-X2C) offers advanced switching features and connection to 10-Gigabit Ethernet networks. Internally it uses the same 1-Gb/s downlink ports as the SBM-GEM-001 for connection to the SuperBlade® LAN interfaces. Externally it provides up to three 10-Gb/s uplink connections (two with a CX4 connector which are stackable and one SFP+) and two 1Gb/s uplink connections (RJ45). It also has two internal Ethernet paths to the CMM(s) to allow configuration, management, and control of the switch and its ports through a browser-based management interface. In addition to the Web-based GUI, it offers a CLI for flexibility in management and control of single or multiple switch networks.
This affordable quad-channel 4Gb/s host bus adapter offers twice the performance of 2Gb/s at a small premium. The 4Gb/s Fibre Channel PCI Express adapter series was created to fulfill virtually any storage connection need or environment, whether data mining, video and media streaming, or providing high availability. These adapters deliver unsurpassed performance and high port density; are easy to install; and can accommodate PCI Express host platforms. All LSI adapters support end-to-end error detection (cycle redundancy check or CRC) for improved data integrity when reading or writing disks.
Since the LSI7404EP-LC is fully compatible with 1 and 2Gb/s legacy products, you are assured of investment protection. This HBA also provides unsurpassed performance for your data-intensive and high-bandwidth applications, while utilizing Fusion-MPT™ architecture to accelerate time to market.
Acme Controls Supplier of switches, limit switches, basic switches, electrical switches, switches for offices, switches for hotels, switches for hospitals and switches for homes.
Mangal Auto Distributors Supplying switches such as combination switches, electric switches, combination switches with hazard warning switch, steel switches, stainless steel switches and automotive switches.
Processing...
