We are manufacturing water purification systems are available in two models that have different specifications. Our water purification systems also have lab models like water producing type ii/iii grade water and suitable for media preparation, buffer, washing laboratory and analytical grade. Some of the standard accessories of our systems include:

• One set of ultra polishing cartridges ultra plugs
• One UV 254 mm
• One EPF 0.22 with filling bell 260 cm 2 area PES
• Power cord
• Instruction manual

In our range of water treatment plants, conductivity of DM water is < 10 micro S/cm at 250 C PH of DM water is 8.5. 9.5 and a maximum pressure of 2.5 Kg/Cm². These plants can be widely used where good quality water of low conductivity is required in general.

We also assist in the setting up of water treatment plants for varied industries. Our water treatment plants are adequately designed with suitable equipments. The procedure of water treatment is conducted analysis of water and supply. Our water treatment plants are cost effective and have long term use. The water treatment procedures include:

• Pressure sand filters and Carbon filters


• Chlorination units


• Softening plant


• DM plants


• RO plants

Distillation is a water purification process that uses a heat source to vaporize water and separate it from contaminants and other undesirable elements commonly found in ground and surface water. Distillation heats raw (untreated) water until the water reaches its boiling point and begins to vaporize. The heat is then kept at a constant temperature to maintain water vaporization while prohibiting other undesirable elements from vaporizing. Water has a lower boiling point than salt and other mineral sediments. This process also separates the water molecules from microscopic, disease-causing organisms. Once all of the water has vaporized, the vapor is led into a condenser, where, upon cooling, the water reverts to the liquid form and runs into a receiving container. The remaining elements, whose boiling point was too high to permit vaporization, remain in the original container and constitute the sediment. Because the distillation process can never ensure a complete separation between water and other materials, it is often repeated one or more times with the treated water. Many alcoholic beverages, like brandy, gin, and whiskey, are distilled, using an apparatus similar in constitution to the water distillation apparatus.

We are manufacturing a range of solvent extraction systems that have the following highlighting points:

Salient Features:

• Remote heating ensures high operator safety
• Direct heating by means of infra red heater also available
• Built-in drying air pump
• Digital Temperature controller
• Optimized cooling circuit
• Adjustable Thimble holders

Advantages:

• Up to 85% saving on Time and Solvent compared to traditional soxhlet method
• Compact and ergonomic design
• Energy saving
• Easy to operate
• Choice of 2, 4 and 6 condenser designs forming the range

Applications:

• Crude fat in
  • Meat
  • Animal fodder
  • Food
  • Pharmaceuticals
• Soluble mineral in:
  • Textile fibers
  • Paper pulp
  • Petrochemical
  • Animal tissues
  • Soils and sediments
  • Agricultural crops
  • Wastewater

Specifications

• Parameter: Thermosox MSE 400 Series
• Range: 0-100% fat
• Solvent recovery: 65-70%
• Solvent Volume: 60-100ml typical
• Temperature controller: Auto tune P.I.D Micro controller
• Temperature range: Ambient to 200C
• Extraction timer: 1-9999 Minutes(Built-in)
• Extraction thimble: Nitrocellulose(Dia 25 x 80 mm)
• Speed of Extraction: 30-60 min depending on sample type
• Reproducibility: +-1%relative or better
• Electrical Requirement: 230 V, 50Hz single phase AC, 500 W

Three Models are available

Cat No.	Capacity
MSE 402	2 Samples at a time
MSE 404	4 Samples at a time
MSE 406	6 Samples at a time

pH meter is a device used for potentiometric pH measurements. pH can be measured using either pH indicators (like phenolophtaleine) - in form of solution or pH strips - or using potentiometric method. Strips are very useful when all you need is 0.5-1 pH unit accuracy. When you need higher precision, pH meter is the only way to go. In potentiometric methods you measure potential difference between known reference electrode and the measuring pH electrode. The latter depends on the activities of ions you want to measure. This dependence is described by Nernst equation, thus once the potential has been measured you can calculate the activity. pH meter is nothing else but precise voltmeter, connected to the pH electrode, and scaled in such a way that it displays not the measured potential, but ready pH value.

Our firm is engaged in manufacturing and exporting of conductivity meters that are available at industry leading prices. These meters have the following specifications:

• Direct reading referred to 25°C
• For conductometric titration's of acids, bases and specific organic compounds in aqueous & aqueous media
• Facility for measurement of absolute cell constant, selection & adjustment of cell constant
• Wide range measurements from power station boiler feed water to 5% Noah
• Expendable to measure total dissolved solids and salinity
• Temperature compensation from 0 to 50°C ( manual), capacitive correction for higher ranges

The assortment of our TDS meters is precision designed and developed to suit the preferences of our customers in diverse industrial sectors. These meters have the following highlighting features:

• Auto ranging
• Microprocessor based
• User friendly, menu driven
• Measures, directly electrolyte conductivity (EC) & total dissolved solids (TDS) in water, aqueous & non aqueous solutions
• Total dissolved solids (TDS) in water, aqueous & non aqueous solutions
• Automatic / Manual temperature compensation from 0-50°C
• Elegantly styled, small laboratory version

We are manufacturing flame photometers that are available in two models that are mentioned below:

Flame Photometers CL 26D

Features:

• Dual Channel
• Concentric Non-corrosible Nebulizer
• Mixing Chamber designed for stable flame

Flame System:

• Stainless Steel round burner with LPG as Fuel & Air as Asoxidant and stainless steel needle type regulator
• Narrow Band interference filters
• Small Quantity of sample needed

Applications: For measurements for concentration of Alkali & Alkali earth metals (Sodium, Potassium, Calcium & Lithium) in Bio – chemical analysis like electrolytes in serum, body fluids, nutrient solutions for cultivation of anti-biotic.

Flame Photometers CL 361

Features:

• Microprocessor based with printer interference
• PC compatibility through RS 232 interference
• Four – element measurement in single aspiration of the sample
• Calibration curve programmability using maximum of 20 standards in the range of interest of the user
• Data processing through optional curve fitting techniques, lease square, quadratic
• Multiple calibration curves saving facility

Applications: To determine Na, K, Ca & Li in:

• Plant materials, food and beverages
• Electrolytes in serum
• Body Fluids (blood, urine etc.)
• Alkali & alkaline earth metals
• Nutrient solutions for cultivation of antibiotics
• Water (natural, spring, waste, river etc.)
• Soils

Photometers are used to measure the intensity of the light produced by an unknown source in terms of a standard source. The general technique is to locate the two sources so that they give the same illumination to two adjacent surfaces.

Features: 

Salt spray chamber (AS TM -117) is constructed by non corroded material of imported clear acrylic sheet. The chamber is single walled, closed by top lid. It is 25 deg slanting type. It is especially provided to condense the fog water which does not allow to fall on the specimen .The specimen is held on or placed at the center of the chamber .It should be maintained at an angle of IDE slanting to the chamber. The top lid is held on the chamber with water seal for controlling the fog leakage .The whole unit is mounded on four wheels.

Saturation Tower:

It is used for preheating the air the air is passed through 40deeg C hot water. This chamber is constructed by acrylic tube coupled with acrylic flange the compressed air enters to the chamber and sterilized with water so that it removes the dust, dirt and oil particles etc. The water enters to the chamber and maintains its level, controlled by water level controller and solenoid valve the heater is connected at the bottom of the flange, which maintains then temp. By digital temp controller.

Control Panel:

It is provided at the sidewall of the main chamber. It contains digital time with battery back up chamber temp. Controller, saturation tower controller, water level controller and solution level indicator. Its other accessories are on/off switch, safety fuse & pilot lamps etc.

Chamber Size: 15 sq feet (AS TM -117)

Dimention: L 750xB 750x H 600mm. Also manufactured as per customer application and specifications.