Acrylic Distemper & Primer

Expression Mitco Premium Acrylic Distemper is an economical interior coating. It gives an excellent clean, quick drying, finish. Expression dries within 2-3 hours therefore successive coats can be applied in quick time. Expression Premium Acrylic Distemper is washable after 7 days from the date of application Brightness and the beauty can be regained by just wiping with mild solution of soap and water.

TECHNICAL DATA:

AREA OF APPLICATION	interior surface
COVERING CAPACITY	10-12sq mt per kg per 2 coat depending upon the shade, surface and surface texture
METHOD OF APPLICATION	Brush. Roller. Spray
DRYING TIME	Surface dries in 30 minutes re-coating time 3 hrs.
FINISH	Smooth. Mattand Beautiful
PACKING AVAILABLE	20Kg,.10kg,.5kg, 1kg

DIRECTIONS FOR USE:

Apply cement primer on the new surface. Fill the rough surface with Impression Wall Putty. Add 500-600 ml of water In 1 kg of Expression Acrylic Distemper. Apply 2-3 coats after gap of 3-4 hours between each coat.

DIRECTION FOR USE

SURFACE PREPARATION:

Newly plastered surface should be allowed to mature for at least 3 months- All loose piaster and the dust parades should be removed with sand paper No. 320 If there is any previous lime wash, colour wash, dry distemper then that must be scrapped off before application flaking paint must be scrapped off and be cleaned with water properly.

Expression Mitco Primer Water Thinable (For Exteriors) is suitable for undercoat for walls, asbestos, concrete, cement before finish coat. It gives a suitable substrate for wall finishing. It is thinned with potable water to achieve applicable consistency. It provides a few special features to substrate as easy brushing, alkali resistant, excellent covering, quick drying and better sealing power. It is used as a primer for painting of Exterior wall finishes (water base) like Exterior Acrylic Emulsions and Exterior Plastic Emulsions etc.

TECHNICAL DATA:

AREA OF APPLICATION	Cementeous wall, concrete, asbestos etc.
VISCOSITY OF SUPPLY	95-110Krebs units at 30°C.
RECOMMENDED THINNER	Potable Water
METHOD OF APPLICATION	Brush. Roller. Spray
CONSISTENCY	Equal part of water to be added in it by volume.
COVERING CAPACITY	15-18 sq Metre/ltr/coat depending upon the surface and surface texture.
DRYING TIME [25-30'C] [60-70 RH]	Surface dry 25 lo 30 minutes where as hard dry in 24 hrs.
FINISH	Matt and very Smooth
SHADE AVAILABLE	Only available in white color
PACKING SIZE	1 ltr, 4ltr, 10ltr, 20 ltr.

Expression Mitco Water Thinnable Primer is suitable for undercoat for walls, asbestos, concrete, cement before finish coat. It gives a suitable substrate for wall finishing. It is thinned with potable water to achieve applicable consistency. It provides a few special features to substrate as easy brushing, alkali resistant, excellent covering. quick drying and better sealing power. It can be used as a primer for painting of wall finishes (water base) like as Acrylic distemper and Plastic Emulsion paint.

AREA OF APPLICATION	Cementeous wall, concrete, asbestos etc.
VISCOSITY OF SUPPLY	100-110Krebs units at 30°C.
RECOMMENDED THINNER	Potable Water
METHOD OF APPLICATION	Brush. Roller. Spray
CONSISTENCY	Equal part of water to be added in it by volume.
COVERING CAPACITY	22-25 sq Metre/ltr/coat depending upon the surface and surface texture.
DRYING TIME [25-30'C] [60-70 RH]	Surface dry 15 to 20 minutes where as hard dry in 24 hrs.
FINISH	Matt and very Smooth
SHADE AVAILABLE	Only available in white color
PACKING SIZE	1 ltr, 4ltr, 10ltr, 20 ltr.

Other Information

• Packaging Details: Available in 20lt./10lt./4lt./1lt.