Temperature Controllers & Indicators

Specification

Model	UTC - 1201	UTC - 1101	UTC - 4201	UTC - 4101
Dimensions(HXWXD) mm	96X96X75	96X96X75	48X48X100	48X48X100
Power Supply	90-270V AC/DC, SMPS
Display	Upper: RED, 4-Digit, 0.56" Lower: GREEN, 4-Digit, 0.4"	RED, 4- Digit,0.56"	Upper: RED, 4-Digit, 0.4" Lower: GREEN, 4-Digit, 0.3"	RED, 4-Digit, 0.4"
Resolution	1˚C / 0.1 ˚C (For Range Less than 400 ˚C)
Indicating Accuracy	± 1% of FSD
Key Setting	By Front Push Buttons
Input  Thermocouple  RTD	J (0 to 600 °C) / K (0 to 1200 °C)
	PT-100 2W/3W (-99.9°C TO 400°C) Selectable
Control   Output  Relay*  SSR  BUZZER	1 Relay, 230V AC, 5A (1C/O) 12V DC ±2V 12V DC ±2V
Relay Action	For TP: Only HEAT MODE For ON-OFF : HEAT MODE or COOL MODE or HIGH ALARM or LOW ALARM Selectable
Control Mode/Action	ON-OFF or Time Proportional (TP) Selectable
Protection Structure /Housing	Plastic ABS Box with Front and Back
Panel Cut-Out (mm)	92X92	92X92	45X45	45X45
Mounting	Flush panel mounting with side clamps fixed behind the Panel
Indication:	“OPEN” message on display for Sensor Break and LED for Relay Status Indication
Protection	Relay turns OFF in case of Sensor Break
Set Point	1 Set Point
Installation	The RTD sensor should be connected to the instrument by proper gauge cables to minimize errors due to cable resistance. For thermocouple sensor, compensating cable of proper type must be used.
*2nd Relay output available on request.

Display : Upper 4D shows Process Temperature, Lower 4D shows Set Temperature I
Range : 0 - 400°C / 0-600°C / 0-1200°C
Input : J or K Type Thermocouple / PT-100 2W/3W
Control Action : Time Proportional and On-Off Selectable, Autotune PID
Setting : Set Point, Hysteresis, Proportional Band, Cycle Time, Manual Reset and Other Control Parameters Adjustable by key pad
Output : Relay output 5Amp.,230VAC
Power Supply : 230V AC ±10% , 50Hz, SMPS
Size : 96X96,72X72,96X48,48X48 mm

NOTE: Instruments are available in single & double display. Temp. Controller with soak timing is also available.

MODEL	MS-5708	MS-1208
Display	4 digit 0.56" seven segment LED display for process value. 2 digit 0.56" seven segment LED display for Channel number. 1 digit 0.56" seven segment LED display for Process Status.	4 digit 0.56" seven segment LED display for process value. 3 digit 0.56" seven segment LED display for Channel number.
Input	4 to 20 mA, 0 to 10V DC, RTD (PT-100 2W/3W) Or Thermocouple(J, K)	Thermocouple J OR K TYPE
Display Scan Time	Adjustable from 2 to 99 sec
Appearance & Dimensions	192 x 96 x 144 mm	96 x 96 x 75 mm
Panel Cutout	188 x 92 mm	92 x 92 mm
Case	M.S. sheet metal case with ABS molded Front & Back	Plastic case with ABS molded Front & Back
Output	6 or 8 relays	-
Features	Grouping of inputs is possible. There can be maximum of 4 groups	-
	Auto / Manual Channel Scanning Facility
Optional Features	RS- 485 interface Available

Temperature Indicator (MDI-38)

• Temperature Indicator of fix input J, K, RTD & R.
• With 4 digits of 0.8" Height.

Loop Powered (LPT-45)
2-Wire Transmitter

• Input : PT-100 2W/3W Thermocouple (Individual)
• O/P Current :4-20 mA

Temperature Transmitter ( MI-73 & MI-63)

• Size : DIN Rail Mounting (70X60X110 OR 76X27X116) mm
• Accuracy : ± 0.5% of FSD
• Input : PT-100 2W/3W, J or K Type Thermocouple.
• Output :0-10VDC,4-20 mA
• Power Supply :110or 230V AC ±20%, 50Hz or 24V AC/DC

Our wide range of Digital Temperature Controllers is highly efficient in offering accurate measurement of temperature. The controller’s protection relay turns off in case of sensor break. We offer our range in various sizes, heights and widths as per the client’s specifications.

 

Technical Specifications

 

MODEL MDC-1901 MDC-2901 MDC-3901H MDC-3901V DTC-49

 

• Dimensions (H X W X D) mm

•  

  • 96 X 96 X 100

  • 72 X 72 X 120

  • 48 X 96 X 120

  • 96 X 48 X 120

  • 48 X 48 X 100

• Display: RED, 3½ DIGITS, 0.56" RED, 3½ DIGITS, 0.4"

• Control Action: ON/OFF or TIME

• PROPORTIONAL: (TP) (Factory Set)

• Input Thermocouple: J (0 to 400 C) or K (0 to 1200 C) or R (0 to 1600 C) J (0 to 400 C) or K (0 to 1200 C) J (0 to 400 C or 0 to 199.9 C) or K (0 to 1200 C)

• RTD PT: 100 2W/3W (0 to 400 C or 0 to 199.9 C or -50.0 to 199.9 C) PT100 2W/3W (0 to 400 C or 0 to 199.9 C) PT100 2W/3W (0 to 400 C or 0 to 199.9 C or -50.0 to 199.9 C)

• Control Output Relay:* 230V AC, 5A (1C/O or 2C/O)

• SSR: 24V DC ± 2 V

• BUZZER: 24V DC ± 2 V

• Resolution: 1 C (0.1 C for range less than 200 C)

• Accuracy: ± 1 % of FSD

• Relay Action: heat mode or cool mode (Factory Set)

• Power Supply: 110/ 230 V AC ± 20%, 50 Hz, 24 V AC/ DC

• Indication led to indicate relay status & sensor break

• Protection relay turns off in case of sensor break

• Installation: The RTD sensor should be connected to the instrument by cables of proper gauge to minimize errors due to cable resistance. For thermocouple sensor, compensating cable of proper type must be used

• Cut Out: (Mm) 92 X 92 68 X 68 44 X 92 X 44 45 X 45

• Mounting flush panel mounting with side clamps fixed behind the panel 2 Relays are available in model MDC- 1902, MDC-1901AL, MDC-2902, MDC- 3902V, MDC-1922 & DTC-49C

• Relay Action: is H+C MODE, H+H MODE (Factory Set), 2nd Set Point relative to main set point, setting by screw driver, in all models except MDC-1922 where both set points are individually settable

With the help of sophisticated infrastructure, latest technology we have come up as one of the top manufacturer of Auto Tune PID Universal Input Temperature Controllers. We have a special team who check on the quality parameters to make sure that these are in accordance with international quality standards. We also make sure that these Temperature Controllers have longer operational life as they are manufactured using superior quality of raw material. We have various kinds of model and sizes along with their complete technical specifications.