We are offering high performing TIG welding machine to our clients. It is precision with TIG (tungsten inert gas) welding. The TIG process can efficiently weld thinner material. It provides the solution for burning through or warping while welding wire or sticks. A non-consumable tungsten electrode and a shielding Gas are used in the welding process to protect the welding area from any contamination. With the concentrated heat and precise control of the TIG arc, thin material (.010 in) can be welded efficiently.

Advantages of Armac Tig Plus include following:

• Welds aluminum, steel and other metals with just gas, argon
• Precise welding on thin materials can be easily obtained
• Less distortion overall

Tig/Argon Welding Machines are featured with following:

• A better & quicker job with les spatter
• Simple operation
• Good arc stricking properties with higher efficiency
• No breakdown
• High efficiency
• Power saving
• Minimum maintenance
• Low running cost

Optional Gtaw (TIG) Accessories offered with the machine is attributed with:

• Gas & Water cooled TIG torches
• Water Cooling System
• Gas flow meter and pressure regulator.
• Remote current control with 10, 25, 50, 100 mtrs Control Copper Cable.
• Tigniter high frequency unit with foot / hand switch.

TECHNICAL DATA COVERING IS-4559-1993

MODEL	AXR-300	AXR-400	AXR-500	AXR-600
INPUT
Supply voltage 3 PH	380/415/440	380/415/440	380/415/440	380/415/440
Primary Current at Max. Output	30A	40A	50A	60A
OUTPUT	D.C.	D.C.	D.C.	D.C.
Open circuit Voltage	85 V	85 V	85 V	90 V
Max. Continuous Current at 100% Duty Cycle	225 A	300 A	340 A	400 A
Max. Continuous at 60% Duty Cycle	300 A	400 A	500 A	600 A
KVA-Max. Continuous	15 KVA	20 KVA	25 KVA	30 KVA
KVA- Max.	20	26	33	43.2
Welding Current range (in Two Ranges)	20-300A	20-400A	20-500A	20-600A
GENERAL
Max. Ambient Temp. to which Rating Apply	40 C	40 C	40 C	40 C
Class of Cooling	H	H	H	H
Type of Cooling	Forced Air Cooled	Forced Air Cooled	Forced Air Cooled	Forced Air Cooled
Approx. Dimensions (LxWxH) mm	658 x 762 x 508	711 x 762 x 546	711 x 762 x 546	736 x 762 x 596
Approx. Weight Kg.	200	220	240	260
Note: In view of continuous development, we reserve the right to modify the design and dimensions without notice. Duty cycles are applicable for 5 minutes at 40 °C.

Our company provides high performing MIG welding machine as per international standard. We offer a series of Mig / Mag CO2 based welding machine including the most rugged TIG welders, STICK welders, MIG welders, SPOT welders, BUTT welders and PUG cutters.

Advantages of the ARMAC Automat are cited below:

• Welds light gauge material or thick plates
• High welding speed can be obtained upto 4 times faster stick welding.
• Reducing repair or construction time.
• In addition to its use for MIG welding, it also performs flux cored welding. Rather than running a solid wire coupled with a shielding gas, flux cored welding uses self-shielded wire with flux inside.

Features of ARMAC portable arc welders include:

• Welds all common metals carbon steel, stainless steel, aluminum
• Continuous wire feed minimizes starts and stop
• Increased metal deposition which is beneficial for hard facing
• Minimum Maintenance
• Power saving
• High efficiency
• Low running cost

Power sources for Mig / Mag CO2 Welding Machine are:

• Constant Voltage
• Fitted with Amps & Volt Meter
• Toggal Button For gas & OCV Checking

Equipment provided with the machine comprise of:

• Power source, wire feeder
• Flow meter, pressure regulator & gas pre-heater

Wire Feeder

• Most easy maintenance wire feeder with 2 roll/4 quick release type
• D.C. drive permanent magnet motor to maintain constant speed, push button for wire inching

Torch

• Heavy duty, light weight & most flexible torch

Specifications:

MODEL	Automat AXM-250	Automat AXM-400	Automat AXM-600
Welding Curreent Range	250 A	400 A	600 A
Input Supply Rating	415 V-3Ph, 50 Hz	415 V-3Ph, 50 Hz	415 V-3Ph, 50 Hz
Open Circuit Voltage	18-38 V	18-52V	18-56V
Welding Current @ 60% D/c	250A	400A	600A
Welding Current @100% D/c	180A	315A	480A
Input Supply Rating @ 60% D/c	8.8KVA	22.5 KVA	35 KVA
Input Supply Rating @ 100% D/C	6.5 KVA	17 KVA	27 KVA
Cooling	FORCED AIR COOLED
Isolation Class	H	H	H
Dimensions (LxWxH) mm	780x460x700	790x510x725	870x600x820
Weight Kg	100	135	170
WIRE FEEDER
Wire Size Steel	0.8	1.2 mm	1.6 mm
Aluminum	1.2 mm	1.6 mm	2 mm
Speed Range Min.	0-18	0-18	0-18
Drive	2 Roll	2 Roll	4 Roll
Control	THYRISTOR	PRINTER	CIRCUIT
Overall Dia mm Spool Size	300	300	300
Bore mm	50	50	50
Weight Appro Kg	10	10	10
Torch	25 A.K	36 KD	40 KD

Note: In view of continuous development, we reserve the right to modify the design and dimensions without notice. Duty cycles are applicable for 5 minutes at 40 °C

We specialize in fabricating highly efficient air plasma cutting machine from quality raw material. Backed by proficient engineers and technicians, we are able to manufacture the machine as per the specific requirements. Featured with rugged construction, easy to operate and easy to maintain, it is widely demanded by clients belonging to various industries.

Features of Air Plasma Cutting Machines are cited below:

• Power Source
• Electrode and nozzles-5sets
• Air cooled hand with 6 mtrs. cable length
• Ground Cable set with 6 mtrs. length
• Front cap-1no

Specifications are tabulated below:

MODELS	APC-30		APC-45		APC-80
Max.Cutting Capacity(mm)	8/16(Fine/Coarse)		16/32(Fine/Coarse)		95/40(Fine/Coarse)
Input Supply	415V,3Phase,Netrural,50/60Hz
Max .D.C. Output Current (Amps.)	40	200	70	300	90	9400
Open Circuit Voltage (Volts)	330	80	300	80	300	80
MMA/TIG Welding Range (Amps)	-----	10-200	-----	10-300	-----	10-400
Torch Cooling	AIR
Dimensions(appx.)(W x D x H) (mm)	400 x 600 x 400				600 x 800 x 1000
Weight(appx.) (kg.)	90	130	120	150	150	200
Air Pressure required	5.5kg/CM2 ,(80 PSI appx.)
Recommended Compressor Cap.	3 HP with 160 Ltrs. Tank Capacity
Main Switch TPNCap.(Amps.)	25		32		50
Input Cables Size (Al./Cu. Sq. mm (3 1/2 core))	10/06/				12/08/

Above models can be supplied with fully thyristorised current control power source as per the demand of our clients

Optional accessories offered with the air plasma cutting machine are:

• Air cooled machine torch with 6mtrs. length
• Trolley with 1.8 mrts steel track and circle cutting attachment
• Air Compressors Gouging Cable length
• Consumable : SElectrodes Nozzles, front cap

Backed by state-of-the-art manufacturing unit, we are able to manufacture qualitative aluminium welding machine. AC/DC Welding Machine / Pug Cutting Machine is offered in different models including STICK welders, MIG welders, BUTT welders, TIG welders, SPOT welders and PUG cutters.

Advantages of ARMAC Multipurpose are listed below:

• A multipurpose argon set is suitable for both S.S and Aluminium Tig Welding.
• ARMAC 400 is a very rugged stick/tig welding machines & is widely used in various industries
• Cost - effective, efficient, flexible & portable
• Stick welding power sources deliver inexpensive options for welding versatility, reliability & portability

Following are attributes of ARMAC portable arc welders:

• Suitable for both S.S and Aluminium Tig Welding
• A better & Quicker job with less spatter
• Forced Draft Fan Cooling (In case Air Cooled)
• Protective Secondary & Primary Terminal under hinged door
• Good are stricking properties with higher efficiency
• Continuous amperage adjustment (mechanical)
• Compact in size and light in weight
• Mounted on Wheel
• Minimum maintenance
• Power saving

AC/DC Welding Machine (Forced Air Cooled)

Model Multipurpose		AXB-400
Welding Current range	AMPS.	10-400
Max. Cont. current at 60% Duty Cycle	AMPS.	400
Max. Cont. current at 100% Duty Cycle	AMPS.	240
Open Circuit Voltage	VOLTS	70
KVA Rating at 60% Duty Cycle	KVA	26
Input Supply	VOLTS	2 lines of 3 Phase
Frequency	HZ	50HZ
Cooling	TYPE	Forced Air Cooled
Insulation	CLASS	H
Type of output Current Regulation	MODE	STEPLESS REGULATION

Pug Cutting Machine

Technical Description of Pug Cutting Machine
Cutting Capacity	:	0-300mm Thick mild steel (Approx). Bevel cutting 75mm thick up to 45 either side of vertical.
Cutting speed Range	:	190-830 mm/ with 220 volts AC, 1s Hz, 1/2 HP electric power motor with rotary resistant control
Cutter PMC-3	:	Vertical adjustment 70mm injector type-Horizontal adjustment 90 mm. Gas Hose connections 1/4" BSP LH for fuel gas & RH for oxygen.
Standard Accessories	:	A-16 cutting Nozzle (1-16"), A-12. Cutting Nozzle (3/64"), 9 Mtrs.3 - core cable, hose nut spanner & head nut spanner.
On Request	:	Pug cutter headcan also be supply in Nozzle Mixing head w/o injector

Note: In view of continuous development, we reserve the right to modify the design and dimensions without notice.

Duty cycles are applicable for 5 minutes at 40 °C.