Our control panels for air conditioning system are made of quality raw material which is at par with international standards. Our experts and designers have enabled us to fabricate the latest design of the market. These are then tested at certain quality parameters to ensure the flawless performance of the range. Panels for Open /hermatically sealed compressor, Fan units , heater banks with Airstst /Thermostat/Humidistat controls. Upto 100 HP .
We are a well known company engaged in designing and manufacturing of AMF Panels (Auto Mains Failure panels) that are applicable for managing DG sets. Our panels come with in-built safety features for protecting the Engine & Alternator. The range of our AMF panels are manufactured upto 500 KVA and are fabricated from 14 SWG thickness, high grade CRCA sheet steel. The use of quality material has made our panels dust &vermin proof. Powder coated for longer life and meticulously wired.
Logic:
Mains Failure: 3-attempt engine cranking after mains failure otherwise the engine fails to start. Engine starts-up within 10 sec of mains failure otherwise 2 more start pulses after every 10-15 seconds.
Unhealthy Mains: Any of the phase failure or voltage drops below set value.
Mains Restoration: Engine keeps running for 30 seconds before stopping, as recommended by the Engine manufacturer.
One Ammeter with CTs & selector switch, one frequency meter, one voltmeter with selector switch and one hour meter.
Set of indications:
Load on DG
Load on mains
Fault indications
LLOP
High water temp/high cylinder head temp
Overload
Set of Push Buttons:
Engine start/stop
Alarm acknowledge button for hooter
Reset button for fault indication
Safety:
High water temperature
Low oil pressure.
Overload trip
Battery Charger: A separate battery charger for continuous charging of batteries in trickle/boost mode to ensure prompt starting of the engine.
We provide fully automatic power factor control panel (APFC) with digital controller, having capacity from 25 kvar to 500 kvar. or more. The panel is guaranteed for maintaining PF above 0.9. It has the following features:
World advanced Micro controller Technology is used
Auto/Manual selector is available
Enclosed with sequencially controlled fans for internal cooling.
Kvar by Kvar selectable system
Power capacitor insytalled at rear side of the panel.
Stage on LED indications are available
Fully enclosed wall mountable/floor mounting.
Working temperature up to 55 degree celsius
Cable entry: Top and Bottom .
Incoming control and total protection of panel with 3pole/ MCCB
Power & control wiring: by copper multi strand ISI wire
Capacitor bank rating: 440v/according to your load required KVAR
Our company is engaged in designing and manufacturing of automation panels that are having an excellent appearance. We have the facility to manufacture these in different shapes like one sided, double sided and desk type. All panels are hard wired, plc based, electrically controlled. These automation panels are made using careful wiring and are used for the below mentioned machines:
Automatic Control Panels for Bag Filter system.
Control Panels for Rubber Extruders
Control Panels for PVC Extruders
Automatic Control Panels for Tyre / Tube Curing Presses
Control Panels for Gantry and EOT Cranes
DC Drive Panels for Sugar Mills
AC Drive Panels for Power Plant Boiler Application
Presenting a range of bus ducts and rising mains that are available upto 4000 A, which can be operated with less than 35 degree Celsius Temperature Rise over an Ambient of 40 degree Celsius. Their short circuit withstands capacity falls at 50kA. The non-segregated bus ducts with inter leaving design are aptly designed for indoor and outdoor installation with IP: 55 degree of protection. All our bus duct systems are type tested with Erection & Commissioning services. We are pioneer in design, engineering & manufacturing of various types of bus ducts and bus trunking systems like:
Phase segregated & non segregated metal enclosed bus duct
We are engaged in manufacturing of feeder pillars that have a specified standard of protection IP:55. These pillars are perfect for outdoor use and are widely applicable in different non-industry and industrial applications. Our specialization lies in designing the pillars as per the specific requirements of the customers. We are achieving accurate results in our production by mixing variety of resources in our manufacturing process. These feeder pillars are extensively used in:
The heating control panels that our company manufactures can control temperature through 64 different temperature control panels in it with PID controller cum indicator. We offer this heating control panels, compact micro controller based electronic instrument that gives indication of actual temperature, set temperature different status of all the heaters that takes RTD, thermocouple inputs and RS232 output port for computer interface.
Our company is engaged in designing and manufacturing of motor control centers or MCC that have the capacity to feed larger loads. Our specialization lies in manufacturing these MCC's as per the specifications provided by the customers at industry leading prices. Also we can supply motor control centers with vacuum contactors, HV ACB upto 6.6 KV with required backup protection and switchgears for HT motors. These MCC units comprise of:
AC variable frequency drives
PLC I/O based control for motors .
Solid-state motor controllers
MCCB/MCB based backup for feeders .
Over load protection with thermal /electronic switchgears
Analog or digital metering
Feeder circuit breakers
Feeder fusible disconnects
Timer based switching of motors .
Control Transformers
Panels will be suitable for 415 ± 6% volt, 3 phase (4 W E) 50 HZ AC supply
Operation from Local/ Remote(LPBS) / PLC based controls.
Technical Specifications:
Operational Current: 32A to 1600A
Ambient Temperature: 40-50 degree Celsius in single and double front
Withstand Capacity: 16KA to 50 KA
Degree of Protection: As per IS Standards upto IP 56
Types of Starters Include: Direct On-line Automatic Star Delta, , Soft Starters, Varied Frequency Drives, Stator Rotor Starters and Auto Transformer Starters. Single phase starters.
Body of panel :Fabricated out of 1.6 mm to 2.5 mm CRCA sheet .
Powder coated/Enamel painted : Any required shade ,after all process .
Installation:They will be installed indoors and will work efficiently up to an ambient temperature of 50°C
Our range of PLC control panels are made of superior grade raw materials, which ensures the durability and efficient performance of our range. The features of our PLC control panels are as follows:
High speed processor
Compact size - I/O capacity up to 8,192 I/O points
We are engaged in manufacturing of power control centers from the best raw materials. These can be availed by our customers having the following general features:
Panels will be suitable for upto 2000 Amps , 50 KA,415 ± 6% volt, 3 phase (4 W E) 50 HZ AC supply
They will be installed indoors and will work efficiently up to an ambient temperature of 50°C
Construction:
Type: Single /double sided.Modular design, free standing and will have fixed or draw out type executions as many be desired.
Finish: The entire panel will undergo pretreatment covering decreasing, water rinsing & de-rusting/ phosphating. It will be synthetic enamel painted or powder coated as per requirements.
Bus Bars: Uniform cross section copper Bus Bars (current density 1.39 amps/sq mm.) supported by SMC /DMC bases will be employed through out the length of the panel.
Internal Wiring: Wiring be carried out with 11000/650 volt grade PVC insulated stranded conductor wire. All joints will be solidly crimped using copper thimbles
Earthing Bus: Bus Bars will be running all along the board.
Switch Gears/ Components Along with the formal offer, the GA drawing and the bill of material will be submitted specifying the makes & capacities of all the material to be used in the panel.
Standards: Our Panels confirms to the standards such as, IS 4237; IS 8623; IS 375
The range of our power distribution panels are mainly used to distribute AC and DC power from one supply to other devices. These type of distribution panels monitor and protect DC systems and serves as an effective power distribution system. Our power distribution panels are applicable in:
Apt Controls And Appliances Private Limited Manufacturer and exporter of water heater thermostat, rod type thermostat, bimetallic enclosure thermostats, programmable thermostats, heating thermostats, electronic thermostats, commercial thermostat, bimetallic thermostats and rod thermostats.
Rajsen Mechatronics & Tools Supplier and manufacturer of automation equipment, industrial automation equipment, frequency inverter, portable frequency inverter, DC frequency inverter and ac drives frequency inverter.
Processing...
