 |  |
|
|
|
|
|
 |
|
|
Energy Regulators Uncompromising attitude towards quality, standards, and designs have enabled us to achieve large clients. The foolproof system of quality checking and measurements at every stage of production guarantees the expected quality, shape, standard and specifications. Our gamut of products include: |
| Energy Regulator The BHA Energy Regulator effects its control by periodically switching the power on and off, the ratio of the on time to the total time determining the average power input. As compared with a variable resistance, the energy regulator is in general cheaper, far less bulky, and applicable to any load up to its rated capacity. Moreover, the control is effected without the loss of energy associated with resistance control, is variable continuously from no load to full load and is substantially independent of mains voltage fluctuations up to about 20%. Functional Description: The energy regulator mainly consists of a heated bimetal and a snap-action switch (spring contact). Technical Specifications:
Applications: Annealing, Melting Pots, Industrial cooking, Dies, Platens, Comfort heating, Electric furnaces, Molding, Industrial hot | |||||||||
| ||||||||||
Infinite Control The infinite control switch gives infinite control for non-inductive loads up to 15 Amps on 120 or 240 V-AC (cannot be used with an external conductor). It can be turned either to left or right to adjust proper heat from 0-100% wattage with infinite control over the first 50% of total wattage. Energized continuously in HI position, at other settings it delivers selected input level under control of a simple bimetal timer. Only 3 mounting holes are necessary to install the Infinite Control Switch in customer supplied box or panel. It is designed for use at ambient temperatures up to 85¢XC. Technical Specifications:
|
| ||||||||||
| |||||||||||
| Industrial Heater
| |||||||||
| ||||||||||
Thermocouple Ceramic Terminal Blocks Thermocouple Ceramic Terminal Discs/Blocks: Steatite quality ceramic Terminal Blocks 25mm dia,42/43mm dia & 54mm dia Simplex, Duplex, 4 way, 6 way,& 8 way with & without brass Parts, & Spring. Loaded M.I. Plates with or without SS Tubes. |
| |||||||||
| ||||||||||
| Thermocouples & Spares Thermocouple Wires: Cromel-Alumel, Iron- Constant, Copper-Constant, imported Bright & Oxidized finish, SWG 10 to 36. PT/PTRH 10%, 13% . Thermocouple Extension & Compensating Cables: Fiber glass covered, PVC / PVC. Asbestos / Asbestosis, Teflon/Teflon, Insulated, Teflon/Fg/SS Braided single pair, multi pair, Type K, J, T, R, and PT-100 RTD Cables 2 core, 3 core, 4 core , 6 core, Also Teflon /silicon rubber Teflon/shielded/Teflon etc qualities. Thermocouple M.I. Cables: SS 316, 310 & Inconel 600 quality type K, J, Simplex 1mm,1.5mm, Simplex & Duplex 3mm,6mm, 8mm, also PT-100 RTD Thermocouple M I Cables SS 316 quality. 3mm, 5mm, 6mm 4 core Thermocouple Assemblies: Straight, L Type , Rotating type, Inmelt Bolt type, Pencil type, Washer, Holder with Spring. Rotating Type, Adjustable Types etc. Made out of SS tube 4.8mm, 6mm,supplied with Spring & Brass bayonets Single Slot & Double Slot , 10mm id, 12mm id, 14mm id, etc. Thermocouple Brass Parts: ADAPTORS 1/8 BSP, 1/4 BSP, 1/2 BSP, 3/8 BSP Single Pin, Double pin Bayonets. Bayonets (Holders): Single slot, Double slot 10mm, 12mm,14mm, 16mm ID, Brass Part for terminal Block. Type No. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10. | ||||||||||
| |||||||||||
Temperature Sensor Thermocouples: The thermocouple principal is derived from using two dissimilar metal conductors and forming a circuit with one junction at a higher temperature than the other. This allows a current to flow and the resultant EMF will be proportional to the temperature difference between the two junctions. The following products are manufactured / supplied:
|
| |||||||||
| ||||||||||
| Industrial Ceramic for Heaters Steatite quality end seal bushes, channels, terminal blocks, formers, washers, tubes £ crushable tubes for cartridge heaters, insulating beads etc. MGO Powder Water grade, Air grade, super air grade and for thermocouples 22 SR Grade. | |||||||||
| ||||||||||
Snap Thermostat The BHA Snap Action Thermostat regulates the temperature continuously by switching the power on and off after the achievement of the set temperature. The Snap Thermostat¡¦s normally closed contacts opens on achieving the set temperature which closes again when the temperature will drop by the differential. Technical Specification:
Dimensions: Length of control shaft and angle of terminal plates are depended on customer requirement. Phillips type iron connection is also available. All dimensions are only for reference. Application: When properly employed, this thermostat is suitable for use in dry / steam iron, ironing machines, waffle maker, hot tray, electric stoves etc. |
| |||||||||
| ||||||||||
| Compression Fittings
| |||||||||
| ||||||||||
Stem Thermostat DESCRIPTION : Thermostat with safety cut out, single pole stem control and double pole safety limiter FEATURES
OPERATION:The differential expansion of the sensing element causes the opening of a snap-action switch in the thermostat head. In case of abnormal temperature rise, the patented MFS technology in the stem or traditional bimetal ensures double pole safety. The limiter is manually resettable. TECHNICAL CHARACTERISTICS:
|
| |||||||||
| ||||||||||
| Variable Micro Soldering Station
One Year Warranty against manufacturing defect Specification
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Stem Thermostat The BHA Stem Thermostat regulates the temperature continuously by switching the power on and off after the achievement of the preset temperature. The Stem Thermostat¡¦s normally closed contacts opens on achieving the preset temperature on certain drop of temperature contacts again becomes closed, the difference between the temperature at which the contacts becomes open & closed is called the hysteresis, which is between 5 to 10„aC. The BHA Stem Thermostat operates with 5% tolerance of the scale printed on the cover, the temperature is set by adjusting the knob over cover. The BHA Stem Thermostat is far more economical, less bulky & accurate as compared with analog temperature controller & capillary type thermostat. Technical Specifications:
|
| |||||||||
| ||||||||||
| Copyright © Peena Traders, All Rights Reserved (Terms of Use) Developed by IndiaMART InterMESH Limited |
 |
)
)
