We offer our clients with assembly line machines for automotive safety belt. We have developed nine machines forming the complete assembly line for assembly of safety belts. The various machines we offer are as follow:

• Mounting frame tie bar swaging m/c
  
• Spring driver assy m/c
  
• Spring cover assy m/c
  
• Spring winding m/c
  
• Sensor cover assy m/c
  
• Bearing pure driving spm
  
• Clutch disc assy m/c
  
• Green can assy m/c
  
• Web pin- pulling m/c

The isotopes are a useful base medicine for treatment of cancer patients.This is prepared inside an SS box, shielded all around by 6” thick lead walls. It comprises of the following parts:

• Trolley
  
• Axis gantry robot
  
• Can-cutting station
  
• Isomantle heating station
  
• Vial dispensing station
  
• Plc controls with hmi

X drive is a single-axis servo slide carrying the inspection system for inspection of coolant channels on reactors.Owing to our expertise, we can offer our clients with machines having customized specifications as per their requirements.The specifications are as follow:

• Movement of slide: 6000mm
  
• Position accuracy: +0.05mm
  
• Payload: 1,500kg
  
• Drive: servo motor through gearbox
  
• Control: Industrial pc
  
• Speed of slide: 225mm/sec (max)
  
• Guide system: Linear motor slide with rack (title)

We have designed these for the pre-stretching of agriculture chains immediately after assembly. The chains are fed into the equipment by pulling through sprockets before dispatch. The operations of the equipment are controlled through a plc. We offer our clients with customized solutions to ensure their complete satisfaction.

We supply the collar height setting SPM to clients engaged in manufacturing automotive brake systems as it forms part of the assembly line. It is used for running of 2ms of nuts on 2 studs in the brake assembly to pre-programmed positions.The machine comprises of rotary table with 4 stations out of which, 2 stations carry locators for the brake assembly and other two carry setting masters.

Designed for pressing diodes on heat sinks hydraulically, our heat sink- diode assembly spm is being widely appreciated by our esteemed clients. There are two types of diodes viz positive as well as negative and the heat sinks also differ. We have installed an hmi to help operator in selecting variety of components angle of indexing, modes of operation etc. Moreover, the operations are controlled by a plc.

The final stage in the assembly of automotive shock absorbers, the machine was designed to close and seal the shock absorber outer tube. These are being made of high quality raw material by using various sophisticated machines. The machine’s operations are controlled by a plc.

The combination of wheel cylinder and back plate is critical in the automotive brake system and are held together with 2 or 4 screws depending on the model. The machine drives the screws with electrical servo nut runner. Our machines have the ability of handling about 7 varieties of components. The change over includes replacement of quick-change stoppers location and selection of the variety on the hmi. The sensors are used for sensing availability of components and operations are controlled by plc.

The thro bolt assembly SPM forms part of the assembly line for production of alteration and carries out the driving of 4 bolts on the assembly. The operation of these machines is controlled by a plc. These are being widely appreciated by our clients in the domestic and international market.

The bush pressing machine drives a bush into the bracket of starter motors. These bushes are driven by a hydraulic cylinder. Our machine is highly effective and is extremely user friendly. The process is as below:

• During assembly a load cell monitor the load and checks is against the specified limits
  
• In case the actual load falls out of range either low or high an alarm is activated and the operations halted
  
• An lvdt is also incorporated to check the depth after pressing operations and controlled by a PLC.

It is used for checking the performance of the oil pumps used on the truck engines for the circulation of engine oil. These are blocks attached to the engine block and are loaded on a locator which is held with studs. The requirement has two stations will locator for the pumps. It helps to load a new Pump on the other station while test on other station is going on. It is fast so that it can be ready for test once the test at the other station gets over so that productivity is enhanced. The operation is controlled by a plc.

We offer our clients with screw driving SPM which carries out driving of 3 or 4 screws on starter motor assemblies. This machine has the capability to handle about 7 varieties of models, where the number of screws and their positions vary. It uses a single air-driver to tighten one screw at a time. Moreover, the driver is moved about by a 2-axis pneumatic-servo system. It is moved from one position to another whose values are programmed into the memory of the plc. The PLC controls the entire operation upon selection of the variety. To enhance productivity, the machine is provided with a cam table with two fixtures to operate on one fixture while operator is loading component on other.