Electronic Equipments

A fix frequency Oscillator for Bridge Experiments, workable on 220 Volts 50 Hz, Giving variable output 0 to 10 volts P-P at 1000 Hz. Accuracy ±2% Output.

Generates frequency from 1 Hz to 250 KHz in 6 steps wave form is sine square and Triangular. Output is variable from 0 to 10 Volts Accuracy ± 3% or 2 Hz. Output Impedance 50 ohms. Solid State. Workable on 220 v 50 Hz complete I.C. version with coarse and fine controls for output

This instrument is to measure Conductance of Electrolyte solution or its Resistance directly. Working frequencies are 50 Hz and 1 KHz. Direct calibration in MHO. Resistance 0.1 Ohms to 1 Meg ohms. Conductance 1 MHO to 1 Micro MHz in seven ranges, Accuracy ±1% mid scale and ±3% on both ends. Null detection on meter with Conductivity Cell.

The instrument is designed to read Conductance of Solution and has wide range of measurement .02 Micro MHo to 1 MHo and in 3.5

 

• Digits read outAccuracy +0.5% or 1
• Digit Display L.E.D. or L.C.D.

Workable on 220 Volt 50 Hz. Measuring range upto 2K/20K gausses. Direct reading calibrated in terms of gausses, 3.5 digits display. Complete with Hall probe.Accuracy ±0.5%.

Display frequency on 6 digit display, Range of measurement from 1 Hz to 50 MHz. Sensitivity of signal 20 mV r.m.s. from 10 Hz to 1 MHz, increasing to 50mVr.m.s. as 1 MHz and 50 MHz. Input protection to 550 V (DC + peak AC). Resolution of 0.1 Hz to 10 Hz and 100 Hz for gatings period of 1 seconds, Accuracy better than ±001% 1 least count.

Capacity measurement 0-10,000 micro farad, Resistance upto 20M ohms and inductance upto 2,000 Henries, D & Q value is also direct readable. 4 Digit L.E.D. display.

Useful for precise and stable pH/mV measurement and ionic activity with specific electrodes, useful for Chemical, Pharmaceutical, Pesticide, Medical, Soil, Agriculture, Water and Laboratories, pH measurement 0 to 14pH corresponding mV measurement 0 to ±199.9 mV. Resolution ±0.01 pH, Accuracy ±1% Temperature Compensation of solution.

A digital instrument with precise potentiometeric measurement of ionic solution. Measuring range 0-200 milli volt, with electrode and standard solution.Dimension : 11"x7"x4½"

Instrument is measure unwanted distorted signal in an amplifier, by feeding pure sine wave and amplified signal passing through filters and distorted signal measured on meter in terms of percentage. The instrument consists of sine wave generator filter circuit and meter. Workable 220 V 50 H. The capability of this instrument is to measure distortion in audioable range 20 Hz to 20 KHz

It is a 20 MHz Dual Channel Oscilloscope that s ideal for, professionals as well as students undergoing technical studies. It is a rugged, light weight instrument that features a brijght, sharply defined trace on a 80 by 100 mm cathode ray tube. The internal trigger signal is ac coupled. An external triggering signal or an external Z-axis modulation signal can be applied via a front panel or rear panel connector and the source selector switch. The horizontal system provides calibration sweep speeds from 0.2s to 0.1 Micro S per division. For greater measurement accuracy a x5 magnifier circuit extends the maximum sweep speed to 20 ns per division. Special Features : Synchronisation of the signals from the two channels can be identified by a Red LED, marked as "READY", present on the right hand side top on the front panel.

 

Instrument consists of power supply for G.M. Tube with digital read out meter. 6 Digit counting system with its power supply. Controls for reset, start and stop through on panel. One presetable timer with 3 digit display and thumb wheel switch. Complete with G.M. Tube, stand, and one radio active source B

Kit is based on 8085 Microprocessor and is designed to provide ease in interaction with 8 bit Microprocessor capabilities. This Kit can be used to train engineers about the Microprocessor Technology, to control any Industrial process and to develop Software for 8085 system. This Kit has a powerful monitor in 4/8 bytes EPROM. The monitor can be extended to incorporate an Assembler and Dissembler for 8085. The Input/Output structure includes programmable 241/O lines. It has got 16 bit programmable Timber/Counter using 8253 for generation of any type of counting. Different types of INTERFACING MODULES from us can be hooked with this kit to perform simple experiments & projects in the lab. These modules are very helpful in learning about the real time inter acing problems of microprocessor.

• Digital Photo Colorimeter 8 filters, mains operated, sample size 1 ml.
• Digital Photo Colorimeter 5 filters, mains operated, sample size 1 ml.
• Filter Photo Colorimeter 8 filters, mains operated, sample size 1 ml (Analog)
• Filter Photo Colorimeter 5 filter, mains operated, sample size 1 ml. (Analog)
• Battery cum mains operated Colorimeter in Digital & Analog models are also available at an additional cost ..... While ordering please mention specifically

Accessories On Request :-

• Standard Glass Filter each colour.
• Test Tube set of 5.
• Selenium Photocell.

To plot a graph, current versus Intensity of light at different value of voltages. Instrument comprises of DC Power Supply 0-10VDC/50mA, two meters for voltage & current measurement, Photo Transistor mounted on the panel, connections of supplies & photo transistor brought on terminals with light source. Dimension 15"x8"x4".

The inst rument produces rectangular pulses. The pulse rate and the pulse width is variable. The pulse amplitude can be selected to trigger T.T.L. Circuit. Specification :- Pulse Time : 10 Micro sec. to 1 sec. variable External Triggering : 2-20 Volts. Pulse Width : 1 Micro sec. to 1 sec.

To verify properties of Resistances when connected in series & parallel. Instrument comprises of Two moving coil meters to measure voltage & current, circuit diagram for series & parallel connections Printed, Resistance mounted along.

Activity : To draw V & I characteristics of a solar cell. The apparatus consists of :