Our nitrogen gas generator is based on P.S.A Technology and that is called “PRESSURE SWING ADSORPTION’’.
NITROGEN GAS GENERATION :- The main ingredient of Nitrogen Plant is CMS (CARBON MOLECULER SIEVE) and CMS is having indefinite pores on the surface, which adsorb the molecules of Oxygen, Moisture and Unwanted gases from compressed air. Nitrogen gas, which is not adsorbed into the surface of CMS comes out from adsorbed tower and collects in the surge vessel.
Nitrogen Generator Models :-
PEE MODEL
This is very simple Model for producing the Commercial grade of Nitrogen with its Purity of 99% and very economical. This Model is suitable up to 99.9% Purity.
DX MODEL
This Model is used as ‘High Purity Nitrogen plant’ wherein the purity level is 1-2 PPM. This type of Plant is used where Hydrogen contents are required. This plant is Commonly used for Heat treatment, Chemical and Electronics industries.

COPPER – DX
This Model is used as ‘ Ultra Pure Nitrogen Plant’ and its Purity level is 1PPM (max). This is used where Nitrogen gas is required, free from Oxygen and Hydrogen. This Model is Commonly used in Optical cable, Electronic and Synthetic Fiber Industries.

Advantage Of P. S. A. Nitrogen Plant :-
• P.S.A Plant is Reliable, Economical, Durable and user friendly.
• Fully Automatic – No special operator required.
• Low generation Cost – Pay Back period within one year.
• Self Contained unit and ready to install.
• Consistency of Purity and no hassles of Nitrogen Cylinder.
• Maintenance cost is very low.Minimum life of CMS is 10-12 year.

APPLICATION OF NIROGEN GAS
• Metallurgical Industry
• Synthetic & Fiber Industry
• Chemical Industries
• Food Packaging Industries
• Pharmaceutical Industry
• Optical industryElectronic Industry
Capacity :- 1Nm3/Hr to 1000 Nm3/Hr

The main ingredient of Oxygen Plant is ZMS (ZEOLITE MOLECULER SIEVE) and ZMS is having indefinite pores on the surface, which adsorb the molecules of Nitrogen, Moisture and Unwanted gases from compressed air. Oxygen gas, which is not adsorbed into the surface of ZMS comes out from adsorbed tower and collects in the surge vessel.
It consists of two-adsorber tower, which is filled with Molecular Sieves. The adsorber towers are interconnected with Change over Control valves, controlled by sequence timer with a standard time cycle. After every certain time cycle adsorbed tower, automatically swings and Oxygen gas is produced continuously. The maximum Oxygen purity level is 93-95%

Advantage :-

• Economical, Durable and user friendly.


• Fully Automatic – No special Operator required.


• Low generation Cost – Pay Back period within one year.


• Self contained unit and ready to install.


• Consistency of Purity and no hassles of Oxygen Cylinder.


• Maintenance cost is very low.


• Minimum life of ZMS is 10-12 year.

Application of Oxygen :-

• Glass Industry


• Steel Industry


• Brazing Industry


• Ampoules and vials Manufacturing


• T.V. Picture Tube Manufacturing Industry


• Hospitals Water Treatment and Fish Farming


• Chemicals and Petrochemicals

Capacity :- 1Nm3/Hr to 300Nm3/Hr

We design, develop and export highly efficient Hydrogen Gas Generator. Used in different industries, its salient features/functions are as follows:

Long Service life of electrolysis pool

Widely applied to different types of Cromotography

Low energy consumption

Liquid level is visible through floating ball

Larger square of electrolysis separation pool, rotational whole structure

Low pool temperature

Our Heatless air dryer consisting of two towers filled with Activated Alumina and at a time one tower is under process and another tower is under regeneration simultaneously. We can achieve dew point of (-) 40 degree C (at atmospheric pressure) we can also get a dew point up to (-) 80 degree C but quantity of purging air will increase up to 25%. The capacities that we offer in this category are 10 NM3 / hr to 1000 NM3 / hr. Some of the features that need to be highlighted are:
Low initial investment and operating cost.
No maintenance.
High performance.
Single Phase Power Supply.
No extra energy required for regeneration
Ambient Working temperature.
Desiccant life 3-5 year.
Dew point (-) 40 degree C.

The Drying unit has 2-vessels filled with Activated Alumina or Molecular sieves desiccant. One vessel remains in drying cycle for 4 hours, while other vessel simultaneously regenerates at atmospheric pressure. Around 3% flow of dryer capacity is used as purge for regeneration. Electrical heaters are provided in a central finned Stainless steel pipe in both drying vessels. Heating cycle is for 2 hours and in this time hot purge air increases desiccant temperature to around 100 degree C. At this temperature regeneration is complete (due to dry air purge). Dew point achieved is around (-) 40 degree C. If still lower Dew point is required, air purging rate is slightly increased to 5% for (-) 60 degree C and to 7.5% for (-) 80 degree C Dew point.

It is a skid-mounted unit consisting of Freon chiller, Air to Air pre-Cooler and a moisture separator. First Air is pre-cooled with outgoing chilled air to around 25° C and then it is cooled in a Freon Chiller to (+) 2° C temperature. This reduces refrigeration load of the Unit. Outgoing dry air has (+) 2° C Pressure Dew Point and comes out at around 25° C temperature. (+) 2°C Dew Point in Refrigerated Air Dryers corresponds to around (-) 23°C Atmospheric Pressure Dew Point. Lower Dew Point is not possible from Refrigerated Dryer, as moisture condensed would start freezing on Freon tubes, if lower dew points are tried.


(-) 23°C is the best possible Dew Point achievable from Refrigerated Air Dryers

The Dryer is fully automatic with pneumatically actuated Ball / Plug valves. A sequence timer controls operation of these valves. Desiccant used is Activated Alumina and it dries the air up to (-) 400 C Dew point.


ADVANTAGE OF HOC DRYER :-

Maintenance cost is very-very low because there is no moving part, no blower and no continuous requirement of Electrical heater.
Life of activated alumina around 5 year.
No loss of compressed Air.
Pressure drop across dryer is max. 0.2 kg/cm2.
Skid mounted and ready to install
Dew point is (-) 400 C.

We supply the following desiccants :-

• Activated Carbon
• Zeolite Molecular Sieve - 13x
• Activated Allumina for Air Drying
• Zeolite Molecular Sieve - 4A
• Nickel Catalyst for Ammonia Cracking
• Zeolite Molecular Sieve
• Palladium Catalyst for Deoxo reaction.
• Cu-catalyst for O2 / H2 removal
• Carbon Molecular Sieve

We carry a vast range of pressure vessels that are manufactured from qualitative materials of carbon steel and stainless steel. The product is used in different industrial applications. Its salient features include:

Durability

Dried With Pneumatic Air

Built-In Temperature Sensors & Control System

We are also dealing with sensor and gas analyzers for the following gases: Oxygen, Hydrogen, CO and CO2. These gas analyzers are in ready stock.

We manufacture and export a comprehensive range of different compressor spares. Produced in our modern manufacturing unit, we offer quality tested, precision parts & components for the compressors. These parts are known for their durability, dimensional accuracy and efficient performance under complex conditions.

Leveraging ion our vast industrial experience, we provide an assortment of air & gas compressor spares. These products are globally acknowledged for their efficiency & accuracy.