Protech Engineering & Controls Private Limited

Site Search:

Home Profile Equipments Contact Us Enquiry

Protective Relays

Battery Chargers

Voltage Stabilisers

Rectifiers & Test Sets

Timers


Showcase
Play now


Diesel Engine Controllers & Protections

Manufacturing a wide range of Diesel Engine Controllers & Diesel Engine Protections, we are catering to wide requirements of our clients. Qualitatively superior, Our diesel engine controllers & diesel engine protections offer maximum performance and are highly energy efficient.

View Enquiry Basket

AMF Futuro 

Supplying a wide range of AMF futuro, we are serving to wide requirements of electrical and electronics industry. These find application in diesel engines of generators and other equipment and have been compactly designed. Customized as per the specifications of our clients, these are known to possess following features:

• MIMIC type of front fascia
• Easy to use
• Indications for DG Set start and Stop, and all faults (LLOP, HWT, O/S, O/L, AUTO LOAD CHANGEOVER, BATT. LOW, SFS and LFL)
• REMOTE monitoring and control facility (optional)
• Connection of external Indicating Lamps and push buttons with simple wiring • User settable parameters on rear ANNUNCIATION with flasher and buzzer including ACCEPT, RESET and TEST facility
• Facility for connection of external HOOTER
• Design facilities easy and quick installation
• Total wireless interiors
• Maintenance Free
• Existing non-AMF panels (standard panel) can be easily converted into AMF panels
• Semi Auto Mode of Operation
• Designed with reduced number of components
• Economical in comparison with conventional type panels This equipment is user friendly and a futuristic AUTO MAINS FAILURE SOLUTION which has been designed adopting latest digital technology thus achieving reliable and accurate
• Start stop operation of DG set
• Load changeover from DG and MAINS
• Fault annunciation for safety of DG Set

Operation


Working on the terminal voltage of Battery i.e. 12V or 24V, these are available in Auto, Semi Auto, Test and Manual operating modes. Sensing all the three phases of mains supply these give starting pulse to DG Set starter (Sart Solenoid) along with FUEL SOLENOID, specially in the cases when any one phase goes below the set limit (settable on rear, 300-400V).

• DG starts automatically when it develops its rated voltage (settable between 300V-400V)
• DG Contactor (or any switching device provided) is switched on after preset time delay
• Power is supplied to load from DG Set
• In case any fault happens on the engine side or over load occurs, supply to load will trip and DG will be stopped automatically and fault is indicated by a flashing LED and buzzer
• Fault acknowledge by pressing ACCEPT push button
• When fault is acknowledged the LED becomes steady and buzzer stops.
• DG can be restarted once again after the fault has been rectified
• On the resumption of the main supply, load is changed over to mains
• Engine stops only after idle tile set(settable on rear)
• Manual mode is also available where in the whole operation is achieved with push buttons
• When this is in the test mode of operation, load changeover become automatic
• Manual engine start and stop operations.
AMF Futuro

Add to Enquiry Basket

Mini Futuro-3Ph. 

We offer an innovative range of Mini futuro-3Ph. which has been designed and developed in accordance with the needs of our clients. Customized as per the specifications of our clients, this is a user friendly auto mains failure Solution for single phase generator sets. These have been manufactured adopting Micro- controller technology to achieve reliable and accurate:

• Start stop operation of DG set
• Load changeover from DG and MAINS
• Fault annunciation for safety of DG Set Designed with reduced number of components, Mini- futuro For 1-Phase model works on the terminal voltage of 12V or 24V.

After sensing the main supply, it starts giving pulses to Gen-Set starter (Start Solenoid), when Mains Voltage (in-built) goes below the set limit. Once the Gen-Set starts, there is developed a rated voltage and the power is supplied to load from Gen-set. In case any fault occurs on the engine side, Gen-set stops automatically, indicating the fault with a respective fault LED & buzzer. Pressing the accept button, fault can be acknowledged stopping the buzzer but the fault LED remains ON. Accomplishing fault rectification and resetting the system, Gen-set starts once again. Once the main supply is resumed, the load is changed-over to mains and the DG Stop Contacts stops the engine after pre decided idle run time which is settable on the front. No manual mode operation required, however in case for manual operation, control supply is disconnected and Gen-set is stared externally. Load change over will happen without DC supply. 3 phase model has been designed for automatic DG start stop and fault annunciation. Potential free contacts from any mains sensing device such as (three phase voltage relay) carries on main sensing and the load changeover is designed externally.

Special features:


• Compact designs
• Designed using latest Micro-controller technology • Simplest single phase AMF controller
• MIMIC type of front fascia
• Easy to use
• INDICATIONS for main ON, Gen-set start & stop, Gen-set ON, Load on mains/Get-set & all faults (Main fail, low lube oil pressure, Battery low, Set fails to start, Alternator fail and low fuel)
• Contactors not required for single phase application
• Annunciation with flasher & buzzer both; including Accept, Reset & Test facility
• Facility for connection of external Hooter
• Design facilitates easy and quick installation
• Maintenance Free
• Existing non-AMF panels(standard panel)
• Can be easily converted in to AMF panels using Mini-Futuro
• Total wireless interiors
• Manual Mode not required.
• AMF-N96-3 Potential Free Contacts for all the faults for external integration
Mini Futuro-3Ph.

Add to Enquiry Basket

Fire Futuro 

Designed adopting latest micro controller technology, our range of Fire Futuro is known for reliable and accurate performance. These are available in standard as well as customized models and possess following specifications:

• Compact & simplest diesel engine controller for fire hydrant system
• MIMIC/ window type front fascia • Easy to Use
• Indications for Mains, ON, FIRE, Engine RUN, Fuel, and all faults (Low Lube Oil
• Pressure, Battery Low, Fails to start, HWT, O/S & Low Fuel)
• Potential Free contacts for all faults for external integration (optional)
• Programmable free inputs
• Conventional panels are easily convertible in automatic panels using fire futoro
Fire Futuro

Add to Enquiry Basket

Reverse Power Relay 

For monitoring the direction of power from AC generators, we offer a wide range of reverse power relay. These have been precisely designed in accordance with the needs of our clients and known to deliver maximum performance. Relay energizes when the current in the system being monitored is reversed to a value greater then the customer adjustable present limit. Some features of the equipment are:

• Adjustable trip point 2 to 20% of input current
• An adjustable time delay of 0 to 20 seconds
• Correct setting of the trip point and time delay ensures protection against motoring in the event of a generator failure and prevent tripping due to transients encountered during synchronization
• Red LED indicates the state of the relay
• Green LED indicates the condition of the power supply
Reverse Power Relay

Add to Enquiry Basket

Automatic Phase Selector Switches 

We manufacture a wide range of Automatic Phase Selector Switch which has been fabricated using superior quality raw material. These phase selector switches have been designed in accordance with the needs of our clients and possess following special features:

• Automatic selection of available phase for single phase load
• Sequence of phases can be prioritized
• Ideal for unmanned operations

Technical Data


• Input: 3-Phase 4 wire 415V 50Hz AC supply
• Output:1-Phase 230V 50Hz AC supply
• Rating: 6A/16A/32A
• Indications: a) R, Y, B Phases, b) Load on R/Y/B Phase (any one at a time)

Dimensions:

6A - 150mm (W)*

75mm (H)*

150mm (D)

16A - 200mm (W)*

100mm (H)*

200mm (D)

32A - 200mm (W)*

100mm (H)*

200mm (D)


Automatic Phase Selector Switches

Add to Enquiry Basket



On Off

--- Equipments ---

Home  |  Profile  |  Equipments  |  Contact Us  |  Enquiry

Member IndiaMART.com© Protech Engineering & Controls Private Limited, All Rights Reserved. (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited