“S” CLASS STERILIZER. Custom Built Chamber Size WITH Micro computerized control & Large LCD screen and With Unique Power failure memory which re-starts process on power resumption.

Robust construction: Double Walled Fully stainless steel

Low Water Level Indication by message & blinking light

User friendly:

single key press starts & completes process without supervision

displays “process over” message on completion * blinking

light for user attention on message on screen * help messages on screen

Password Protection prevents tampering of set parameters

User programmable : Temp: 120 to 135 deg. C, Time: 15 to 59 mins

Safety: process power configured in cut-off mde in its steady state of rest

Mechanical Safety valve.

Self Diagnostic Software identifies process faults and displays on screen e.g.: Sensor error, Heating not progressing etc etc

Versatility: permits stop & edit at any time during process run

Reporting: Total Time Taken & No. of Power Failures during process.

Optional: Drying Cycle

The superior quality double walled dental acrylizer has been constructed using stainless steel which has been painted with attractive stone enamel. Quite user friendly, the machine can be easily operated by a mere single key press. While using it, the gaps between the walls are fitted with glass wool in order to minimize the temperature loss. This is further controlled by using hydraulic thermostat from 5c above ambient to 100c with sensitivity 06 5c. All these highly effective dental acrylizer machines are provided with mechanical German timers which can be easily set for a duration between ½ hours to 2 hours. They are accompanied with bras drain plugs, two indicator control knobs & a durable on/off switch.

Our dental acrylizers have features like :

• Micro computerized control
• Has a large LCD screen for messages & values
• Auto restart facility
• Is versatile in nature & permits stop & edit at any time during process on
• Has user programmable time
• Is protected from tampering of set parameters
• Has a self diagnostics software
• Is constructed of stainless steel

Our dental autoclaves have micro computerised control with LCD screen for messages. These dental autoclaves have unique features like :

• Power failure memory - Auto re-starts process on power resumption.
• User friendly - single key press starts & completes process on its own
• Supervision not required 
• Displays “process over” message on completion
• Blinking light for user attention on message on screen 
• Help messages on screen Protection from tampering of set parameters.
• Password incorporated User programmable - Temp: 121 to 135 deg. C, Time: 15 to 59 mins.
• Safety valve - Automatic release of steam on completion of wet claving cycle Front Loading type construction for ease of operation.
• Robust construction - Stainless steel claving chamber with M. S. Powder Coated Control body.
• Safety - Process power configured in cut-off mde in its steady state of rest. Self Diagnostic Software identifies process faults and displays on screen e.g.: Sensor error, Check Water Level, Heating not progressing, etc.
• Versatility - Permits stop & edit at any time during process run Provision to Run Wet Cycle alone or Wet and Dry Cycle Both with auto steam release.

A user friendly computerized equipment, cast duplicator permits incorporation of a large number of essential unique features giving high value for the cost. Built with a optimum capacity of about 3 kg, cast duplicator is absolutely ideal for everyday work. Mere pressing of a single key starts it along with the guidelines flashing on the screen to aid the user. Cast duplicator has other features which are :

• Micro computerized control
• Large LCD screen for messages & values
• In built Power Failure Memory which auto re-starts the process on resumption of power.
• Password incorporation protects from tampering of set values by unauthorised persons.
• Is user programmable including temperature & time
• Has the stirrer on/off facility by front panel key switch
• Prepares & maintains duplicating gel in readily usable form for indefinite period
• Has low power uniform heating, thus, prevents burning of gel from all sides
• The low speed stirrer ensures homogeneous mixing without splashing
• Has a convenient outlet for ease of dispensing
• Is constructed of stainless steel

Designed with utmost care, electro polisher is extremely affluent & primarily eliminates the investment residues for which it has been majorly created. The machine as well helps in eradicating all oxidation after primary & secondary welding. Easily cleans the frameworks as well places where acrylic resin is present. The electro polisher is appropriate for polishing of dental alloy steel which are braces & cast partials. This is done to provide a bright glossy surface with durable luster. Our electro polisher has the following features :

• Has an electronic control circuit
• Continuously protects against accidental short circuit & over current
• The automatic current control is based on electrolyte & objects which regulates the polishing rate
• Has a continuous power setting through knob over the polishing range
• Has a large digital display for seeing the polishing rate

We offer programmable vacuum mixers which have micro computerized control with LCD screen for messages and process result and with unique single run mode for trial of new investment / plaster. Our range of programmable vacuum mixers possess the following features :

• 5 programmes 3 levels in each programme: pre-mix, mix and post-mix time
• Fully automatic hands free operations
• Edit and save / run facility
• Vacuum Gauge for Vacuum Display

Capacity: 3 tons
Perfectly packs the flask after filling acrylic
Exerts uniform pressure throughout the surface
Hydraulic gauge indicates pressure in tons
Ease of operation
Simple release mechanism

Our range of plaster dispensers have 10 kg capacity auto operation at the flick of a switch. No pulling of lever required dispensing and start / stop controlled by toggle switch. These plaster dispensers have features like :

• Flexible mounting : wall or table
• Specification : Construction - M.S. Powder Coated ; Size - 13” x 13” x 17” approx
• Operating Voltage : 230 Volts /- 10%, 50 Hz, 1Phase
• Control Type : Fully automatic by Toggle Switch Dispensing Rate - 300 gms per minute minimum capacity 10 Kgs
• Mounting : Flexible - wall or table top as desired by user

Electronic control circuit ensures steady heating at set temperature
Continuous uniform heating to enable concentration on pattern making
Ultra light weight carving pencil reduces fatigue of the fingers.
Temperature control from 60 to 160 deg. Centigrade. Marking on dial
Fast heating
DUAL CHANNEL WITH INDEPENDENT TEMPERATURE CONTROLS
2 TECHNICIANS CAN WORK SIMULTANEOUSLY.
 
Last But Not Least
Ultra low power consumption resulting in Ultra low operating cost.
 
Approximately 100 Hours of continuous use of both channels simultaneously at maximum temperature results in consumption of
 
ONLY ONE UNIT OF ELECTRICITY
 
Specifications :
 
Construction: Controller                  Light Weight M. S. Powder Coated
                       Carving Pencil        Moulded
Power Consumption                      5 Watts Max per channel at peak temp
Operating Voltage                           230 Volts +/- 10%, 50 Hz, 1Phase
Controller Type                               Electronic
Operation                                       Continuous indefinitely

We offer recycling sandblaster which have large blasting chamber with light. Our range of recycling sandblaster have the following features :

• Large blasting chamber with light
• Two blasting nozzles : Hand pencil for micro (250 microns) sand for ceramic work & Fixed nozzle for macro (400 microns) sand for white metal work
• Macro blasting with fixed nozzle recycles sand utilizing full abrasive strength.
• Micro blasting done with hand held carbide nozzle.
• Micro sand is filled in a jar outside chamber. Used sand falls within chamber which is once again recycled by macro blasting thereby allowing maximum utilization of the abrasive strength.
• Hand switch to change  blasting mode: micro to macro and vice versa.
• Provision for connecting dust extractor
• Foot Switch operations.        
• Operating Pressure 3 to 3.5 bars with pressure zone marked on the gauge.

OPTIONAL : Filter module for protection from dust (dust suction).

Specifications :

Construction	M. S. Powder Coated
Sizes (approx)	18” x 12” x 24”(H)
Working Pressure	3 – 3.5 Bar
Max. Connecting Air Pressure	0 – 10 Bars
Power Supply	230 Volts +/- 10%, 50 Hz, 1Phase
Power Consumption	8 / 10 Watts for lighting

We offer dental ultrasonic cleaner that is specially made for dentists with 1.5 ltr. tank capacity. Tanks with higher capacities can also be made on request. Our range of dental ultrasonic cleaners have features like :

• Fully stainless steel tank enclosed in durable stainless steel water resistant housing.
• High power balancing circuit with ideally placed vibrators for efficient cleaning.
• Built in heater with thermal cut-off and on/off switch to regulate heating.
• Microprocessor based count down timer programmable for upto 60 mins.
• Instant cleaning power released on start up.
• Meshed tray for maximum unobstructed transfer of cleaning power to the jobs to be cleaned.
• Dimensions designed to optimally accommodate all hand instruments.

Specifications :

Construction		Fully Stainless Steel
Tank Size	Standard	230 x 30 x 65 mm
	Custom	As per design
Tank Capacity	Standard	1.5 litre
	Custom	Upto 20 Litres based on customer requirement
Input Supply		230 V AC, 50 Hz, 1 Phase
Average Power	Standard	80 Watts
	Custom	Upto 750 Watts as per design
Peak Power	Standard	160 Watts
	Custom	Upto 1000 Watts as per design
Cleaning Frequency		30 KHz +/- 10%
Generator		Solid State MOSFET Design
Timer		60 Mins Programmable
Heater		Provided with Thermostat and switch
Control		Front Panel Key Switches

Indispensable unit for Porosity Free Polymerization of Heat Cure Resin in crowns and bridges Time saving. Performs process very fast at the press of a button.Micro controller based fully automatic unit Big screen for display of messages and menu Cost saving. 10 models can be cured at a time.