Quality Engineering CorporationQuality Engineering Corporation


Products










Home » Products » Soil Testing Equipment

Soil Testing Equipment

Offering high class Soil Testing Equipment, Manufactured using superior quality raw material – the best stainless steel and brass that is available, - these instruments have earned the praises of our clients for their optimum performance and ease of operation



Laboratory Concrete Mixer

Laboratory Concrete Mixer is laboratory type & is electrically operated. The counter balance drum is easy to tilt with 1½ to 2 cu .ft. mix. The total drum volume is, however, 3 cu. ft. Mounted on a sturdy rubber tyred stand; the drum is mounted for end discharge and equipped with 1/2 h. p. electric motor, suitable for operation on 220 volts. A. C. single phase.



Laboratory Concrete Mixer



Concrete Test Hammer

We are suppling and exporting best qulity of Concrete Test Hammer. This is intended for non-destructive testing of the quality of concrete in finished structures. In testing, the rebound number is measured, which is dependent on the strength of the mortar (concrete with coarse particles) close to the surface. Since the strength of the mortar as a rule determines the strength of the concrete, the rebound number gives an indication for the strength of the concrete. The results obtained are ±15% of the actual compressive strength. As the test does not destroy the specimen, the curing process continuing after setting of concrete the be followed up accurately.



Concrete Test Hammer



Vee Bee Consistometer

We are leading manufacturer and exporter of Vee Bee Consistometer.  Consists of a vibrator table resting upon elastic supports, metal post, sheet metal cone open at both ends, and a standard iron rod. The table is equipped with an electrically operated vibrometer mounted under it by an electric motor, both double ended shaft, working on 220 volts, single phase A.C. supply.

The steel cone is 30 cm high, with dia at the bottom 20 cm and at top 10 cm. A swivel arm holder is fixed to the base, into which is telescoped another swievel arm with funnel and guide sleeve. A graduated rod is fixed on to the swievel arm and at the end of the graduated armecords the slump of the concrete cone, and the volume of concrete cone after vibration of cone in the pot. Complete with electrical accessories.



Vee Bee Consistometer



Mechanical Sieve Shaker

We are offering wide range of Sieve Shaker Mechanical.

Hand Operated:- This is light, portable but sturdy sieve shaker suitable for bench mounting. The side to side movement to he carrier which can take up to 7 sieves of 15 cm or 20 cm diameter is through a train of gears operated by a hand wheel. A heavy fly wheel ensures smooth operation. Supplied without sieves, lid and receiver. Motorised:-Carries up to 7 sieves of 20 cm diameter. The shaker is driven by a 1/4 hp. electric motor through a reduction gear. The sieve table does not rotable but is inclined from the vertical axis and the direction changes progressively in the clockwise direction. By removal of a stop-pin fixed to below the table, the shaker can have a rotatory motion. In addition to the gyratory motion of the table, there is an upward and downward movement ensuring that each square cm of the sieve is utilized. The whole gear mechanism runs in an oil bath. Suitable for operation on 230 volts, 50 cycles, single phase, AC supply- Supplied without sieves, lid and receiver and time switch. Optional Extras : Adaptor for 30cm diameter sieves.Time switch, 0-60, min. graduations. 



Mechanical Sieve Shaker



Load Frame Hand Operated

We are leading manufacturer and supplier of Load Frame Hand Operated. This is a light weight but sturdy load frame designed for application of penetration load in laboratory or field CBR tests on soils, and compressive loads in triaxial shear test. It is designed for a maximum load upto 5000 kg. And consists of a two speed screw jack mounted in a frame and with identical top and base channel pieces so that the unit can be placed either way up and the device can be used for loading from above or from below which ever is convenient.



Load Frame Hand Operated



Sampling Augers

We are dealing in wide range of Sampling Augers outfit. Post-holed auger. Complete with 1 meter rod, tee piece, and handle head size 3", 4" and 6"dia. Sampling Augers outfit-screw type auger, complete with 1 meter rod, tee piece, and handle head size 2", 3" dia. Extension rod 1 meter with end couplings.



Sampling Augers



Split Spoon Sampler

We are leading manufacturer, supplier and exporter of Split Spoon Sampler. The sampler is used in soil exploration used for determining the penetration (N Value) for soil by giving a number of blows with a given weight falling through a given distance and by measuring the length of penetration at different depths. It meets the requirements of IS-2131 and is made from a tube split length wise and held together by a head fitted with a ball check valve, and a hardened steel shoe. The sampler is 50.8 mm in outer diameter and has an inside cutting edge of 35 mm. After it is forced into the soil by ramming and withdrawn from the hole, the shoe and head are unscrewed, and the sampler open like a book.



Split Spoon Sampler



Unconfined Compression Test Apparatus

We are dealing in Unconfined Compression Test Apparatus. Hand operated for trimming various diameter specimens for trixial and unconfined compression test. Motorised it consists of a base with a knife support. The platform supporting the specimen ring rotates slowly driven by a fractional h. P. Motor with reduction gear housed inside the base. The hardened steel trimming knife is mounted on a support, and is adjustable both horizontally and vertically, which permits trimming of the specimen to the exact size of the ring. A guide prevents overcutting. For use with 65 mm, 3 inch and 4 1/4" diameter specimen rings.



Unconfined Compression Test Apparatus



Motorized Liquid Limit Device

Motorized Liquid Limit Device Same as above but fitted with a motor geared down to give approximately 120 RPM. Suitable for operation on 230 volts. Single phase, 50 cycles, A.C. supply Spares: Casagrande grooving tool. ASTM Grooving tool.



Motorized Liquid Limit Device



Specific Gravity Bottle

We are leading manufacturer, supplier and exporter of Specific Gravity Bottle. A small bottle or flask used to measure the specific gravities of liquids; the bottle is weighed when it is filled with the liquid whose specific gravity is to be determined, when filled with a reference liquid, and when empty. Also known as density bottle; relative-density bottle.



Specific Gravity Bottle



Density Basket

We are one of the leading organization engaged in providing excellent quality Density Basket, which are manufactured by using high grade material. These Density Baskets are widely appreciated by our clients which are situated all round the nation. High in demand, these Density Baskets are available at most reasonable prices.



Density Basket



Concrete Test Cylinder Moulds

We are offering wide range of Concrete Test Cylinder Moulds. These moulds are constructed of plated steel for rust resistance and are dimensionally stable under severe use.
Moulds are split along one side with 2 quick-acting clamps welded to mould. When open, mould springs apart slightly to allow specimen removal. Include detachable base plate.



Concrete Test Cylinder Moulds



Concrete Test Hammer

We are leading manufacturer, supplier and exporter of Concrete Test Hammer. This is for evaluating the strength of soil on field exploration or construction site and in the preliminary laboratory studies.It gives directly the unconfined strength.



Concrete Test Hammer



CBR Apparatus

We are leading manufacturers, wholesaler and exporter of CBR Apparatus. Unit consists of Steel Bearing Plates 25 mm thick of 75, 60, 45 and 30 cm dia Plain and Checkered . Bridge support complete with two dial gauge clamps.Hydraulic Jack 50/tonnes capacity complete with 2 meter steel pipe connection with separate pump and pressure gauge. Ball and socket for the jack.Load Truss complete with four soil anchors and working collars. Capacity 20 and 30 ton.Dial gauge .01 mm least count.



CBR Apparatus



Laboratory Pulveriser

The Laboratory Pulveriser is a disc type grinder designed for grinding virtually any mateial to produce a fine mesh sample in one operation. The pulveriser is adopted for use in assay offices, metallurgical, aggregate, quarry, chemical and industrial laboratories. It is a self contained grinder furnished with rotating disc having a planetary movement in verticle plane. This feature gives added life to the waring parts and delivers a product of uniform fineness. The pulveriser will reduce a 1 pound sample of quartz type material to 100 mesh or above in 1 minute. Maximum feed size 6 mm.



Laboratory Pulveriser



Glass Pycnometer

We are leading manufacturer, supplier and exporter of Glass Pycnometer.

Comprises a 2 ibs. glass jar with metal cone, locking ring and rubber seal.



Glass Pycnometer



Dorry Abrasion Machine

We are leading manufacturer, supplier and exporter of Dorry Abrasion Machine. For testing the aggregates for resistance to abrasion in accordance with the standard peocedure laid down in BS : 812. The apparatus consists of a metal disc which revolves in a horizontal plane on a vertical shaft. A suitable attachment for holding the specimen with its axis vertical and its lower end pressed with a prescribed pressure against the surface of the disc (the distance from the centre of specimen to the centre of shaft being 25 cm) is provided. A convenient funnel for feeding sand continuosly upon the rotating disc is also provided. The machine is fitted with a 1/4 h.p. electric motor, driven through a reduction gear to 28-30 revolutions of the disc per minute. Suitable for operation from 220/230 volts, single phase, A.C.supply.

 



Dorry Abrasion Machine



Compaction Factor Apparatus

We are leading manufacturer and supplier of Compaction Factor Apparatus. For determination the workability of concrete provided the nominal maximum size of the aggregate does not exceed 38 mm. This is designed primarily for use in the laboratory but in suitable circumstances, it may also be used in the field. This test is more precise and sensitive and is particularly useful to concrete mixes of very low workability such as are normally used when concrete is to be compacted by vibration. Consists of two hoppers and a cylinder mounted on a rigid frame. The inside surfaces are machined smooth. The whole apparatus is furnished in hammertone spray. Complete with two trowels and a tamping rod.



Compaction Factor Apparatus





Contact Us
Quality Engineering Corporation
Mr. Amjad Ali (Managing Director)
No. 329, Old Tehsil, Civil Hospital Road
Roorkee - 247667, Uttarakhand, India

Contact via E-mail


Home  |  Profile  |  Products  |  Trade Offers (20)   |  Site Navigation  |  Contact Us

Member IndiaMART.com © Quality Engineering Corporation. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited