Industrial Blower

Specification: OUTPUT POWER :0.2 Kw to 29 Kw     MAX FLOW:2500 m3/Hr (1470 CFM)     MAX PRESSURE:1050 mbar (422 in H2O)     MAX VACUUM:730 mbar (293 in H2O)     STAGES:SINGLE/DOUBLE/MULTI     ELECTRICAL:(i) 220 VAC, 50 Hz, SINGLE PHASE                       (ii) 440 VAC, 50 Hz, THREE PHASE Feature: The Ring Blowers / Side Channel Blowers / Regenerative Blowers / Vortex Blowers/Turbine Blowers are suitable for all those applications requiring considerably higher pressure, than those which can be achieved using centrifugal fans.Side Channel exhausters are used in all those applications requiring an operating vacuum higher than the one achievable by a fan, but not as to require the use of a vacuum pump.The rotating parts are not in contact with the casing. The other main features are: • Higher pressure Ratio • 100% Oil-Free Air • IP 54 Protection • Class F insulation • CE approved • Aesthetically Appealing • No, Vibration, and therefore complete Dynamic stability • Cooler running, Double sealed NSK (Japan) Bearings • Provided with inlet and outlet silencer/ filter • Higher pressure Ratio • Low temperature rise • Pulsation- Free Discharge • Compact Yet Rugged • Minimal & Simple Maintenance • Low Noise Level (65dba Normal, 85 dba Max.) • 140% Overload protection • ±10% Voltage fluctuation tolerance Application Of Blowers: ·Pneumatic conveying of solids / liquids ·Vacuum transfer of components / sheets ·Blowing away debris /sucking away debris ·During printing feed/ transfer of paper sheets ·Sorting/counting of cards/envelopes/papers ·Waste disposal /slurry declogging in waste ·Air bearing ·Furnace fuel burning ·Agitation of liquid bath to clean ·Beverage bottling/labeling/drying ·Medical / dental suction units.

Normally RING BLOWERS (Also known as REGENERATIVE/SIDE CHANNEL/TURBINE/VORTEX BLOWERS) are associated with medium pressure and vacuum applications.

Higher pressure/vacuum applications are normally served by TWIN LOBE (Also popularly known as ROOTS) blowers and pumps.

There are some inherent deficiencies with Lobe blowers and pumps. Some of them are:

• Higher initial cost
• High Running Cost
• Lower Efficiency
• High Noise Levels
• Frequent and costly maintenance
• Poor Output Air Quality
• Pulsating Output Air Flow
• Requires Periodic Lubrication
• Higher Heat Generation
• Sometimes requires elaborate controls
                                    
HIGH PRESSURE/VACUUM SERIES RING BLOWER

These are available with following specifications.
• Max Pressure up to 1040 mbar (418 inch H2O)
• Max Vacuum up to 730 mbar  (293 inch H2O)
• Max Flow up to 170 m3/Hr (100 CFM)
• Power Ratings from 0.55 kw up to 7.5kw
• Electrical Ratings from 220 VAC/50Hz/ Single Phase OR 415VAC/50Hz/Three Phase 

Typical applications of HIGH PRESSURE AND VACUUM SERIES RING BLOWERS are:
• Aeration of deep tanks
• Agitation of Viscous liquids
• Effluent treatment Plants
• Waste Disposal Plants
• Large Tanker Discharge Systems
• Pneumatic conveying of heavier materials
• Pneumatic conveying systems involving longer paths
• Process Plants
• Bio Gas Plants
Viscous Fluid Transfer Plants and many more 

The Side Channel Blowers are suitable for all those applications requiring considerably higher pressure, than those which can be achieved using centrifugal blower

Power Rating :	0.20kw To 25kw
Maximum Flow :	2050 M3/hr
Maximum Pressure :	670 Mbar
Maximum Vacuum :	460 Mbar

The Turbine Blowers are suitable for all those applications requiring considerably higher pressure, than those which can be achieved using centrifugal blower

Power Rating :	0.20kw To 25kw
Maximum Flow :	2050 M3/hr
Maximum Pressure :	670 Mbar
Maximum Vacuum :	460 Mbar

The Vortex Blowers are suitable for all those applications requiring considerably higher pressure, than those which can be achieved using centrifugal blower.

Power Rating :	0.20kw To 25kw
Maximum Flow :	2050 M3/hr
Maximum Pressure :	670 Mbar
Maximum Vacuum :	460 Mbar

The Regenerative Blowers are suitable for all those applications requiring considerably higher pressure, than those which can be achieved using centrifugal blower.

Power Rating :	0.20kw To 25kw
Maximum Flow :	2050 M3/hr
Maximum Pressure :	670 Mbar
Maximum Vacuum :	460 Mbar

The Vacuum Blowers are suitable for all those applications requiring considerably higher pressure, than those which can be achieved using centrifugal blower

Power Rating :	0.20kw To 25kw
Maximum Flow :	2050 M3/hr
Maximum Pressure :	670 Mbar
Maximum Vacuum :	460 Mbar

Centrifugal Blowers/ Turbo Blowers/ Radial Blowers/ Medium Pressure Blowers

zero Loss Direct Drive

A centrifugal blower is a blower designed to move air in a confined area. The centrifugal blower has a number of blades mounted around the hub, which turns on a shaft that passes through the housing. The air enters the inlet of the impeller and by use of centrifugal force (hence the name) accelerates over the impeller. A Centrifugal blower can come in three different types of impeller blades. They can come with forward curved blades, backward curved blades and straight radial blades. These impellers can be open type or closed type. Each design has its unique features.

In Zero Loss direct drive blowers, motor body is directly mounted onto housing and impeller is fixed on to rotor shaft.

This arrangement reduces the transmission losses to zero.

The other main features are:

•ZERO LOSS DIRECT DRIVE                                 
  -  Increases Performance
  -  Saves Energy Cost
  -  Reduces Maintenance Down Time As Well As Cost
  -  Makes It Rugged and Compact                
  -  Makes Installation Easy     
•These Blower Can Be Integrated With Variable Frequency Drives To Achieve Optimum   Performance at Reduced Energy Cost.   
•Unique Design Allows Our Blowers To Achieve High Levels Of Flow And Pressure
•100% Oil-Free Air
•Heavy Duty Aluminum Alloy Housing And Cover 
•Low Noise Level
•Specially Designed Impeller Maintains A Constant And Steady Air Flow Stream.      
•Exclusive Squirrel Cage Motor And Shaft Are Designed To Last
•Pulsation Free Discharge
•Minimum Maintenance
•Aesthetically Appealing
•Double Sealed Pre-Greased Bearings Reduces  Maintenance
•Dynamically Balanced Impellers    
•Low Temperature Rise 
•Rated For Continuous Duty

Application:

•Printing Machines
•Incinerators
•Plastic Extruders, Laminators, Film Processing Machines
•Uniform Temperature Equipment
•Household Machines
•Dust Collectors
•Textile Machines 
•Pollution Machines
•Exhausting Gases & Vapors
•Filter Installations
•Furnaces
•Food Industries
•Climate Control
•Hot Air Blowers 
•Dryers
•Pneumatic Transport
•Machinery for the Food & Beverage Industries
•Cooling Machinery
•Woodworking Machines
•Grain Elevators