To provide our customers with solid carbide end mills that can be relied upon, we utilize highly sophisticated 6-Axis CNC tool cutter grinding machines. Our efficient and precise CNC processes consistently yield carbide end mills to the highest level of quality possible. Rohit solid carbide end mills are produced from ultra fine micro grain carbide having high wear resistance and combined with titanium nitride( TiN) and  TiALN coatings, these endmills are capable for machining materials with hardness of upto 55 HrC.

We specialize in the production of solid carbide end mills ranging from 3- 20mm, upto 200mm in length. We can provide you with two, three, and four flute square, ball nose and corner radius end mills, in both standard and non-standard sizes tailored directly to your needs.

The following is a brief about our regular endmill sizes:

Shank Dia (mm)	Cutting Dia (mm)	Flute Length (mm)	OAL  (mm)
3	3	10	38
4	4	12	50
5	5	14	50
6	6	16	50
8	8	20	50
10	10	25	75
12	12	30	75
14	14	32	100
16	16	40	100

Besides we can offer you custom endmills tailored directly to your specific requirements.

(High Speed Steel) HSS tool bits manufactured and exported by are available in the following range:

• ROHIT 1X (HSS – M2) : Tools are manufactured from M-2 quality high speed steel. This is recommended for use on non-ferrous metals only which are basically soft or have low final strength.

• ROHIT 2X HSS 5% Cobalt (SAE – M35) : Exceptionally good toughness and red hardness, most suitable for heavy work on difficult materials and an ideal general purpose tool bit for machine shops.

• ROHIT Special 8% Cobalt (SAE M42) : Tool bits made from 8% Cobalt have high heat and abrasion resistance giving them long cutting life.

• ROHIT 3X HSS 10% Cobalt (AISI – T-42) : Manufactured from finest High Speed Steel this quality of tool bit retains its RED HARDNESS at high temperatures and is most suitable for machining high alloy steels and various grades of stainless steels.

• ROHIT 3X EC500 : Manufactured from High Speed Steel containing 10% Cobalt these tools are CRYOGENICALLY treated for superior performance and life when compared to ordinary 10% cobalt tools.

Thus, Rohit cut-off blades are designed with all required clearance angles built within them.

We offer a wide range of solid carbide drills, which provides maximum wear resistant while cutting high carbon, alloy and stainless steels, titanium, high temperature alloys, aluminum, bronze, cast and ductile iron. It has the following features:

• Better tool finishes
• Superior wear resistant
• Increased thermal resistant
• Better coating adhesion
• Sharper edges
• Higher speeds and feeds

Our capabilities in the manufacture of High speed and Carbide cutting tools means that we are perfectly placed to offer a full range of HSS Drill blanks in standard and extra lengths and in High Speed and Cobalt materials.

Our range of (High Speed Steel) HSS drill blanks are manufactured using superior grade steel to provide efficient performance to the end users.

Ground drill blanks are the same length as jobber length drills and hardened (RC 63-65) and parallel ground (no taper) to required tolerances. All blanks have a bright finish and are made to BS328 / DIN338N / ISO235/1 standards.

These are available in the following HSS grades:  

• 1X HSS – M2 : The tools are made from M-2 high quality steel.
• Special 8% Cobalt (SAE M42) : Manufactured from M-42 quality steel containing 8% cobalt.
  

We offer a wide range of single point turning tools, which are profiled with 5 to 10 degrees positive top rake angle. As a result they generate less heat and cut more freely with a cleaner surface. Made from solid HSS, our range can provide greater heat sink and more rigid setup especially for materials with high coefficient of thermal expansion. Further, to ensure adequate support for the cutting edge the front clearance angle is kept to the minimum.

Grooving tools are manufactured using impact resistant and high quality steel of grades like M2, M35 and T42. These are capable of working against a bore wall. Can cut small diameter groove on the face of the work piece. Ground from solid HSS blanks they provide much smaller diameters than can be obtained from insert type tooling along with superior rigidity, higher strength and wear characteristics.  

We offer a wide range of (High Speed Steel) HSS punches, which are available in different shapes like hexagonal, square or triangular.

Regular Punches
Punches manufactured by us are used in metal fabruication industries. These are perfect for pressing through sheets of metals and into a die to form desired shapes on the metals. It is widely used for its efficient and long-lasting performance.

Double Step Punches
We also offer double step punches that are capable of handling multiple die casting application in one go.

These are widely used in making perforations, holes of varied shapes like triangle, square, hexagonal in various kind of fasteners industry.

Apart from this, our range is manufactured using raw material like HSS M2 and can also be provided with ASP 2030 powdered metallurgical steel.

• Shank diameter ranging from 0.5 mm to 2 mm (head 0.5 mm)
• Shank diameter ranging from 2.1 mm to 25 mm (head 1.0 mm)
• Lengths from 50mm to 200mm

We offer a wide range of HSS Punches and ejector pins, which are made of qualitative M2 steel. Available in various shapes and sizes like bevel headed or semi straight and semi bevel headed. It has the following specifications:

• Shank diameter ranging from 0.5 mm to 2 mm (head 0.5 mm)
• Shank diameter ranging from 2.1 mm to 25 mm (head 1.0 mm)
• Lengths from 50mm to 200mm