Rx Marine InternationalRx Marine International


Our Product Range










Home » Our Product Range » Tank Cleaning Chemical

Tank Cleaning Chemical

Our product range includes a wide range of Tank Cleaning Chemical such as Tank Clean HD, Sea Cleaner, Alkaline Safety Liquid, Chem break Emulsion Breaker, CTC VOLC Cleaner, New Org and many more items.

Tank Cleaning Chemical



Tank Clean HD

Tank Clean HD


Item Code: RXSOL-20-2001-025

Code: RXSOL-20-2001-025

RXSOL-20-2001-025
is highly concentrated organic/inorganic emulsifier with powerful penetrating agents, corrosion inhibitors and surfactants. Quickly removes oil, grease, grimes, adhesive and dyes. Best results also achieved for cleaning of oil side of fuel and lube oil heat exchangers.

Active Matter: 98 - 100 %

Packaging: 25.00 Ltr.

Application:

  • Used as a tank cleaner or for general degrease, cleaning and gs freeing for double bottom tanks, wing tanks, pipe lines, fuel oil tanks, etc.

Dose:

  • Refer to technical data sheet.





Sea Cleaner

Sea Cleaner


Item Code: RXSOL-20-2027

RXSOL-20-2027 is an extremely effective liquid blend of concentrated emulsifier with penetrating agents,mild abrasion-vs and wetting agents which makes this an excellent liquid scouring cleansers for cleaning and degrease of double bottom, deep tanks etc which is used for fuel oils It can also be used for boilers, marine diesel engine cooling water system and for local cleaning and degrease of engine rooms on deck.

Packaging : 25,000 ltr.

Directions for Use and Dose Rates:

  • RXSOL-20-2027-025 is specially formulated for cleaning double bottom, deep and wing tanks etc, used for fuel oils. It can also be used for local cleaning and degrease of engine rooms and on deck.

Soak Method:

  • For hew soil put parts into undiluted RXSOL-20-2027-025, for general soiling use a solution of 10-30% RXSOL-20-2027-025 in water. Parts should be soaked for at least 30 minutes before washing off with water.

Spraying Method:

  • Use neat RXSOL-20-2027-025 over all soiled areas. Allow 10•20 minutes for reaction, then rinse with high pressure water hose.. Scrubbing will assist the cleaning operation for stubborn deposits.

Rock and Roll Method:

  • Recommended time to clean and gas.free under normal circumstances would be 3.6 (lays ,for cleaning of double bottom tanks at sea.
First of all heat the remaining oil in tank:
  • By stripping constantly, flush the tank with sea water
  • Close all suction and discharge valves
  • 1" Dose Fill the tanks by 1/2 to 1 liter RXSOL-20-2027-025 per tone of water through pipe or manhole , for 75.80% of capacity of tank to be cleaned.
  • Then fill tank to 25% capacity with seawater, raise the temperature up to 60°C maximum, and maintain this temperature for 24 hours.
  • Top up tank to 75•80% capacity with seawater, continue to heat for 48 to 72 hours.
  • Discharge and strip tank. Fill to 50.60% capacity with sea water and allow 2 hours rinsing time.
  • Discharge tank and strip, flushing tank with sea water for 2 hours,stripping continuously. When completed, inspect tank to ascertain if second cleaning is required. If so:
  • For completion add second dose of RXSOL-20-2027-025, fill tank with seawater 75-80% capacity and raise the temperature to 60°C maximum. Maintain this for 48 to 72 hours. And recirculate the solution .
  • Discharge and strip tank, flush with seawater, stripping continuously for 2 hours. 11) To gas.free, fill tank with sea water to overflow through vents and sounding pipes, discharge and skin completely.

Technical Specifications:

  • Highly effective concentrated cleaner.
  • Versatile, can be used for a wide application range (for TANK or general cleaning.
  • Provides quick and thorough emulsifying action.
  • Can be used for cleaning , gas freeing of double Bottom, deep and other fuel oil bunker tanks.
  • May also be used for cleaning and gas freeing of crude and refined mineral oil cargo tanks.
  • It can be used as a general purpose cleaner to remove oil and grease deposits and Cleaning of bilge spaces and engine rooms from soiled surfaces. Can be used for degrease and cleaning





Alkaleen Safety Liquid

Alkaleen Safety Liquid


Item Code: RXSOL-20-2004-025

Code: RXSOL-20-2004-025

RXSOL-20-2004 is a mixture of emulsifiers, surfactants, corrosion inhibitors and rust preventives, being non caustic very gentle on hand & ideal for cleaning walls wood works, metal and other areas. Prevents the corrosion of metal such as zinc, aluminum, copper, brass and tin.Specialized for cargo tank cleaning and gas freeing of tanks.

Packaging: 25.00 Ltr.

Application:

  • RXSOL-20-2004-025 is designed to clean animal /vegetables oils, hydrocarbons, Removes dirt, light carbonized grease, lube oil, heavy oils etc.
  • RXSOL-20-2004-025 is a high qua* product classified as a vegetable oil, animal oil, fat, fuel oil, lube oil and pet coke residues general remover/cleaner applied to cargo and storage tanks as well as to other systems. Furthermore, it removes carbonaceous deposits This powerful concentrated formula provides immediate and efficient results while it acts as an odor eliminator.

Note:

  • Lower cleaning temperature required to prevent polymerization of some natural oils. But whenever possible, the cleaning solution should be heated to 60-80°C
  • 1" of all by stripping suction removes all possible oil (greasy materials). To prevents evaporation of lighter fraction oil flush the system with cold water. May be brushed on, sprayed (Hand spray/Direct injection) recirculate the system with PXSOL-20-2004-025 Solution

Dose:

  • Peter to technical data sheet Note: RXSOL-20-2004 has a deodorizing nature and is not flammable.
  • RXSOL-20-2004-025 containing corrosion inhibitors to prevents the corrosion of metals such as Zinc, Aluminum, Copper , Brass and Tin. RXSOL-20-2004-025 is designed to clean Animal I Vegetables oils, Fats, Hydrocarbon removes Dirt, link, Carbonized grease, Oil, Heavy oils etc. Specialized for Cargo Tank cleaning,Gas /Hydrocarbon freezing of tanks.





Chembreak Emulsion Breaker

Chembreak Emulsion Breaker


Item Code: RXSOL-20-2006-025

Code: RXSOL-20-2006-025

RXSOL-20-2006- has the unique feature that dissociates slop to separate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker "C" cleaners.

Application:

  • Ideally suited for slop tanks. Also recommend- need for local cleaning & degrease of engine rooms, bilges & tank tops. Low toxicity, non - corrosive. Highly effective, economical solvent cleaner.

Dose:

  • For light contamination dilute with water in the ratio1:20.For medium contamination dilute with a petrol solvent.And for heavy contamination concentrated RXSOL-20-2006-0210 is suggested.





CTC VOLC Cleaner

CTC VOLC Cleaner


Item Code: RXSOL-20-2028-025

Code : RXSOL-20-2028-025

RXSOL-20-2028 is a very strong cleaner, which can be used to soften up / remove baked on drying oils and used after animal and vegetable oils, fish oils, tall oils, tug oils etc it is low toxic product with an exceptional solvency power on soil & oily matter. It is free from hydrocarbon solvents, Biodegradable minimizes the extreme hazards to personnel in handling materials.Suitable for cleaning of Lube oils Gas oil Kerosene Mineral oil Products. Phosphates paraffin's vegetable oils Dour intensive products.

Using-Procedure:

  • First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2028 is by direct injection followed by recirculation washing, using tank cleaning machines.

Spraying Method:

  • Using CTC as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butter-worth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Incorporate rectangle nri if Orinoco rps It ha< [-loon precarious fresh water rinse and dry.

"Make sure to take all safety precautions are followed when handling/spraying CTC."

Injection Method:-

  • I lot applicable.

Re- Circulation Method:-

  • Fill tank with fresh water and heat up to warm 50°C . IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and CTC to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butter worth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.

"Use a strainer at the pump stack when circulating any solution." Tank Lining— Stainless / Epoxy/ Phenolic, "

Dose:

  • Necessary concentration in water only 0,2 to 0,4 %

Note:
 
  • Removes grease, oil, carbon deposits, soil and grime.
  • Keeps loosened deposits in suspension preventing re.deposition.
  • Low toxic. ,Nonflammable,
  • Free from hydrocarbon solvents
  • Effective and economical in use, Water.based cleaner.
  • RXSOL-20-2028-210 has numerous cleaning applications including removal of greases, waxes, oil, sludge, soot, carbon deposits and general dirt and grime.
  • Non-corrosive to ferrous metals. Suitable for all tank•coatings.
  • Can be used for gas and hydrocarbon freeing of tanks.
  • Can be used for deodorizing
  • Contains wetting agents.

Note:-

  • Acts as an acid.neutralizing agent also.





New Org

New Org


Item Code: RXSOL-20-2020-025

Code: RXSOL-20-2020-025

RXSOL-20-2020
is an extremely effective liquid blend of concentrated emulsifier with penetrating agents , mild abrasives and wetting agents which makes this an excellent liquid scouring cleansers for cleaning and degrease of double bottom, deep tanks etc which is used for RPO / fuel oils It can also be used for boilers, marine diesel engine cooling water system and for local cleaning and degrease of engine rooms on deck.

Packaging: 25000 ltr.

Directions for Use and Dose Rates:

RXSOL-20-2020 is specially formulated for cleaning double bottom, deep and wing tanks etc, used for fuel oils. It can also be used for local cleaning and degrease of engine rooms and on deck. Soak Method for heavy soil put parts into undiluted RXSOL-20-2020, for general soiling use a solution of 10-30% PXSOL-20-2020 water Parts should be soaked for at least 30 minutes before washing off with water. Spraying Method Use neat RXSOL -20-2020 over all soiled areas. Allow 10-20 minutes for reaction , then rinse with high pressure water hose., Scrubbing will assist the cleaning operation for stubborn deposits.

Rock and Roll Method Recommended time to clean and gas-free under normal circumstances would be 3-6 days ,for cleaning of double bottom tanks at sea.

  • First of all heat the remaining oil in tanks,
  • By stripping constantly, flush the tank with sea water,
  • Close all suction and discharge valves.
  • 1st Dose Fill the tanks by 1/2 to 1 liter RXSOL•20•2020 per tone of water through pipe or manhole , for 75-80% of capacity of tank to be cleaned.
  • Then fill tank to 25% capacity with sea water, raise the temperature up to 60°C maximum, and maintain this temperature for 24 hours.
  • Top up tank to 75-80% capacity with seawater, continue to heat for 48 to 72 hours.
  • Discharge and strip tank. Fill to 50-60% capacity with seawater and allow 2 hours rinsing time.
  • Discharge tank and strip, flushing tank with sea water for 2 hours,stripping continuously. When completed, inspect tank to ascertain if second cleaning is required.
  • For completion add second dose of RXSOL -20-2020 , fill tank with sea water 75-80% capacity and raise the temperature to 60°C maximum. Maintain this for 48 to 72 hours. And recirculate the solution.
  • Discharge and strip tank, flush with sea water, stripping continuously for 2 hours.
  • To gas-free, fill tank with seawater to overflow through vents and sounding pipes, discharge and strip completely Dosage Chart for Rock and Poll Cleaning Fuel Oil Viscountcy Confiscates at
  • 50°C Over 320 and sludge tanks RXSOL -20-2020/ 1000 Ltr of water
  • 1st Stage 1 liter 1 liter
  • 2nd Stage 1 liter 150- 300 0.75 liter Up to 50

Physical Properties:

  • Color Light brown liquid DENSITY In g/cm3 at 15°C: 0.9 Flash point Above 70 °C Packaging order No:.RXSOL-20-2020 Size (in liters)25 „ 21
Characteristics:

  • Highly effective concentrated cleaner
  • Versatile, can be used for a wide application range (tor TANK or general cleaning .
  • Provides quick and thorough emulsifying action.
  • Can be used for cleaning, gas freeing of double bottom, deep and other fuel oil bunker tanks.
  • May also be used for cleaning and gas-freeing of crude and refined mineral oil cargo tanks.
  • It can be used as a general purpose cleaner to remove oil and grease deposits and cleaning of bilge spaces and engine rooms from soiled surfaces.
  • Can be used for degrease and cleaning engine cooling water systems Read the Material Safety Data Sheet before using this product





Hydrocarbon Remover

Hydrocarbon Remover


Item Code: RXSOL-20-2008-210

This product is vent common to use for removing of traces hydrocarbons from tank, after cleaning of tanks from solvent base tank cleaning materials . when possibilities of next cargo will contaminate with hydrocarbon.. packaging :25 ltrs , 210 W.

Active Matter :

  • 89-94%

Packaging :

  • 210.00 ltr





Mud & Silt Remover

Mud & Silt Remover


Item Code: RXSOL-23-2900

It is a odorless pale yellow porpoised viscous liquid for removal of sediments, silt and mud. Its polymerization dual effect mechanism help to prevent hard deposition of mud layer on metal surface as well as keeps mud particle in loose condition which causes more labor to clean .

Application :

  • Polyethylene conditioner is highly economical , non toxic, non polluting chemical its lower concentration effectiveness with water keeps it in very economical grade materials class.

Common name:
Mud & silt dispersant ( cleaner ) Reduces unwanted mud load form tanks.

Packaging : 25 Ltrs, 210 Ltrs

Active Matter : 78-86%

Application:

  • This conditioner is highly economical , non toxic , non polluting chemical its lower concentration effectiveness with water keeps it in very economical grade materials class. Mud Remover uses the chemical principle of flocculation to attract mud particles into "flocs" (small fluffy particles). As a result, the "stickiness" of the mud is greatly reduced, preventing it from packing down and allowing for easy flushing by the water flow during debasing.
 
Field for use: -

  • Ballast Tanks
  • Double Bottom
  • Tanks
  • Floating Dry docks
  • Manual Tank Cleaning
  • Cooling Water Systems

Benefits -

  • Increases cargo carrying capacity
  • Aids in removal of existing mud deposits
  • Lowers corrosion rates
  • Prevents mud buildup
  • Easier tank inspections by regulatory agencies
  • Reduces fuel costs
  • Enhances tank coating performance

Continued use of Sediment Remover prevents the deposition of sediments, mud or silt in ballast tanks, cooling water systems, pipelines etc.. Further, it can be used with mechanical action to dislodge existing mud or silt in ballast tanks. Sediment Remover should be injected in small quantities into ballast or cooling water systems prior to filling the tanks or system. If heavy deposits are present, an increased dosage will remove a portion of the sediment after each application.

Note:

Reduces unwanted mud load form tanks RXSOL-23-2900 is a liquid cationic polymer of high molecular weight, specifically designed to treat, condition and prevent the deposit of mud and sediment commonly found in ship's ballast tanks.RXSOL-23-2900 uses the chemical principle of flocculation to attract mud particles into small fluffy particles. As a result, the "stickiness" of the mud is reduced, preventing it from packing down and allowing for easy flushing by the water flow during declassifying. RXSOL-23-2900 is considered nonhazardous and nontoxic, but as is normal when handling any chemical, care should be exercised to prevent eye or skin contact. Should contact occur, wash affected areas with water. Standard protective equipment is recommended.

  • Physical Properties
  • Clear to pale yellow liquid
  • Specific Gravity: 1.06@20'C
  • pH: 8.5

Technical Specifications:

  • A highly effective liquid compound for the removal of sediments, silt and mud from ballast tanks, cooling water systems, pipelines.
  • Sediment Remover will keep mud in suspension and will clean fouled systems completely provided the appropriate dosage levels and application times are adhered to.
  • Sediment Remover is a Polymer based product It does not contain acid, alkali or solvent Sediment Remover is completely biodegradable and has no hazard indications.





Sea Clean Plus

Sea Clean Plus


Item Code: RXSOL-20-2027-025

Product Description:
Seaclean Plus is a modern low-toxic, biodegradable solvent based product. It meets IMO’s requirements regarding safety and pollution hazards of chemicals.

Applications:
This product is excellent as a tank cleaner and degreaser. Directions for Use and Dose Rates Direct injection method - for tank cleaning machines The dose rate should be between 0.1-0.2% i.e. 1-2 liters per ton wash water. Recirculation method - for tank cleaning machines It is advised to use a solution of 0.1-0.2% i.e. 1-2 liters per ton wash water mixed in the tank to be cleaned. The washing solution is usually 5-10% of the tank capacity. Dose rates and results will vary depending on contamination, the temperature of the cleaning solution, and number of tanks to be cleaned with the solution. Best results are obtained when water is heated to a temperature between 65-80°C

Spot cleaning:
Seaclean Plus can be sprayed neat onto tank surfaces to be cleaned. The contact time should be at least 30 minutes. Bulkheads/walls can be washed down by use of tank washing machines or high pressure cleaning machines. The best result is achieved with hot water between 60-80°C. Slops should be constantly stripped from the tank and transferred to a holding tank or pumped ashore to slop tanks.

Spray method:
Spray Seaclean Plus undiluted onto soiled areas. Allow between 15-30 minutes of penetration time before rinsing off with water.

Features, Benefits and Applications:
1.Highly concentrated tank cleaner with quick penetration and powerful emulsifying properties.
2.The emulsifying agents in this product are biological degradable.
3.Does not contain nonyl phenol ethoxylates or other estrogenic compounds.
4.Versatile, can be used for a wide range of applications.
5.Easy to use by any conventional means.





Cold Wash

Cold Wash


Item Code: Rxsol-10-2003-025

COLD WASH GENERAL(RXSOL-10-2003) Introduction:
RXSOL-10-2003-CW is a unique formulation blended with oxidized fatty Compound and high flash point solvents( due to that can be used undiluted up to 70°C) with powerful dispersing agent along with ionic and non ionic surfactant . OB1005 is readily soluble in water in all proportions .RXSOL-10-2003 is non- corrosive to metal like copper, aluminum, Mild steel, and plastic. It is non toxic which makes handling easy.

Functions:
Complete removal of dirt, oil, carbonized grease, heavy oil, gum , vegetable oil , Lube oil, soot , asphalt ,paraffin, carbon stains etc. Gives clear finish to the surface. Highly effective for the removal of crude and other high melting point stains.

PROCEDURE OF USE :
1st Method ( SPRAY METHOD ):- Mix 1 part of RXSOL-10-2003-CW with 2 -10 parts of water / GAS-OIL ( For heavy oil, greasy surface use directly)Spray directly on the entire surface to be cleaned. This can be achieved by Hand spray / mechanical spray pump. Immediately after 2 -5 minted of spray the RXSOL-10-2003-CW starts its function. The Dirt, oil grease etc will loosen. 5 to 6 minutes after spraying start rinsing the system with water (High pressure recommended). Dirt and mud starts vanishing with cleaning media and water.

2nd Method (IMMERSION PROCESS ):-
Application in immersion process with or without ultrasonic support, manual wiping.

3rd Method (RE-CIRCULATION METHOD ):-
RXSOL-10-2003-CW is also used in conjunction with alkaline degreasing bath at 2-10% (v/v) concentration for better and quick degreasing action. Either’s the bath is heated to be 70°Cor the solution can be stirred or air agitated. FINALLY RINSE THE SYSTEM WITH FRESH WATER.

Advantages :
RXSOL-10-2003 is easily soluble in water Action is quite fast even at low temperature which gives advantages of cleaning under operation And avoid shut down and down time. on corrosive to most of the metals / plastics. Gives clear finish to the surface .Lower cost due to high concentration.

Fields of Application:
Treated for the really tough daily cleaning problems faced in the proper Maintenance of Industrial and Institutional physical plants. Can be used as a stripper for all types of waxes and finishes and as a Degreaser where regular cleaners will not perform. May be brushed on , sprayed or used in a dip tank . Excellent for use as a wash for fuel tankers & as a liquid steam jenny compound.

Caution:
AVOID contact of RXSOL-10-2003 with skin or eye Contact. If contact occurs wash with ample quantity of water. NOTE : on dilution RXSOL-10-2003-CW is more effective and safe for use on epoxy, polyurethane ,zinc-silicate coatings and stainless steel.





Dye Remover (ORG Dichlor)

Dye Remover (ORG Dichlor)


Item Code: RXSOL-20-2018-025

Description:–
RXSOL ORG DICHLOR Mixture of Emulsifier, new technology OXIDIZER, Corrosion inhibitors, Rust preventive. due to free from  caustic  and Hydrocarbon very  gentle on hands & ideal  for  cleaning  Walls  Wood  works, Metals  and  all areas . Acts as superior quality cleaner / degreaser.
**These products become more aggressive with temperature increase, and should not  be allowed to dry on  tank walls or stored in cargo tanks as cleaning solution or slops.

Bleach will –
• Remove odors.
• Remove color.
• Improve permanganate time.

Spraying – Following rough washing to a good Water White or better, apply dilute RXSOL ORG DICHLOR to 1 – 3% strength.  First wet the tank surface (spray with DI water), then spray all over with Bleach, wait 30 minute  (but do not allow to dry) and then rinse very well with DI water, including the tank top towards the sump.  To  ensure  that you have covered all areas properly, this process should be carried out at least twice with good DI water. Injection no.
 
Re-circulation– Following rough washing  to a good Water White standard  or  better, apply  dilute  RXSOL  ORG DICHLOR  to 1-3% strength.  Mix sufficient RXSOL—org-dichlor with fresh water in the tank and heat this mixture to 40 – 50 0 C, circulate through the drop line if fitted  and  than  circulate  through  Butterworth  machine  for  3 hours.  After re-circulation immediately warm Butterworth to (500 C) the tank for 3 hours at maximum  pressure, increase the water temperature to 80-85 o C after 45 minutes.  Check (by smell) that there is no RXSOL—ORG-Dichlor remaining, then fresh water rinse and dry.

1. When there are a number of tanks requiring re-circulation, it may be significantly more efficient to.
2. Make up a large batch or number of batches that can be transferred on between tanks as required.
3. Use a strainer at the pump stack when circulating any solution.
4. Tank Lining – Stainless / Zinc / Epoxy / Phenolic (Extreme care must be taken if product other than bleach  
    substitute is to be used in any coated space)





LAC (Liquid Alkaline Cleaner)

LAC (Liquid Alkaline Cleaner)


Item Code: RXSOL-20-2015-025

Description:-
LAC liquid alkaline cleaner is a combination of fast-acting detergents, wetting agents and alkaline cleaners blended in a water-based carrier. It is applied as a highly diluted solution, with fresh or salt water, to remove edible fats and oils, as well as light fuel and lube oils from cargo and storage tanks and associated systems. LAC liquid alkaline cleaner can be used as a tank deodorizer when tanks have been cleaned with petroleum based tank cleaners. LAC liquid alkaline cleaner can also be used as a general purpose cleaner to remove oil and grease from surfaces in the engine and deck departments and other areas where grease and oil are encountered. In addition, LAC liquid alkaline cleaner can be used in boiling out new or retuned boilers, as well as in cleaning contaminated boilers and associated systems. LAC liquid alkaline cleaner should be diluted to a concentration of 20% or less in water before use in systems containing non-ferrous metals. LAC liquid alkaline cleaner has been evaluated by the IMO Bulk Liquids and Gases (BLG) Working Group on the Evaluation of Safety and Pollution Hazards of Chemicals (ESPH) and found to meet the requirements of Paragraph 1.8.2 of the Procedures & Arrangements Standards and is listed on the IMO MEPC.2/CIRC.11. Only cleaners listed on the IMO MEPC.2/ CIRC.11 can be used for cargo tank cleaning when cargo residue slops are disposable at sea.

Application and Use:-

Preliminary Considerations for Any Cleaning Method:
• Tanks should be stripped completely at the recommended cargo pumping temperatures.
• To avoid delays, all equipment for the cleaning method to be used should be onboard and in a condition ready
   for use before cleaning is begun.
• Tanks containing drying oils should be cleaned with cold water immediately after discharge to prevent
   formation of a hard, tenacious residue.
• Adequate ventilation should be provided and other standard procedures should be observed to allow personnel
   to enter tanks as soon as possible after unloading.

Machine Washing:-
• Direct Injection Method (the once-through or total loss method).
• Introduce LAC liquid alkaline cleaner directly into the tank wash-water line by means of an educator or small 
   metering pump. Adjust the feed rate to give the correct solution strength (0.2%-0.8%).
• The tank should be stripped continuously while washing.
• Rinse the tank with ambient temperature water immediately after cleaning with LAC liquid alkaline cleaner.
• If necessary, spot clean manually to remove any patches of soil material that remain after cleaning.

Recirculation Method:-
• While filling the recirculation tank with water, add the amount of LAC liquid alkaline cleaner required for correct 
  solution strength (0.2%-0.8%).
• Except for the fact that tanks being washed are stripped back to the recirculation tank, the procedure is similar
  to that for once-through washing.
  
Rock-and-Roll Method:
• Fill the tanks to be cleaned with water to the required level, at the same time adding enough LAC liquid
   alkaline  cleaner to give correct solution strength (0.2%- 0.8%).
• If a warm or hot cleaning solution is required, apply full heat on the heating coils until proper.
                                  





Furnace Oil Cleaner (Rxsol FO)

Furnace Oil Cleaner (Rxsol FO)


Item Code: RXSOL-20-2030-025

Product Description:-
RXSOL-20-2030 is an extremely effective liquid blend of concentrated emulsifier with penetrating agents, mild abrasives and wetting agents which makes this an excellent liquid scouring cleansers for cleaning and degreasing of double bottom, deep tanks etc which is used for fuel oils It can also be used for BOILERS, MARINE DIESEL ENGINE COOLING WATER SYSTEM and for local cleaning and degreasing of engine rooms on deck.

Directions for Use and Dose Rates:
RXSOL-20-2030 is specially formulated for cleaning double bottom, deep and wing tanks etc, used for fuel oils. It can also be used for local cleaning and degreasing of engine rooms and on deck. Soak Method for  heavy  soil  put  parts into undiluted RXSOL-20-2030, for general soiling use a solution of 10-30% RXSOL-20 water. Parts should be soaked for at least 30 minutes before washing off with  water. Spraying  Method  Use  neat  RXSOL-20-2030  over  all  soiled areas. Allow 10-20 minutes for reaction , then rinse with high pressure water hose., Scrubbing will assist the cleaning operation for stubborn deposits.

Rock and Roll Method Recommended time to clean and gas-free under normal circumstances would be 3-days ,for cleaning of double bottom tanks at sea.
1. First of all heat the remaining oil in tanks.
2. By stripping constantly. flush the tank with sea water,
3. Close all suction and discharge valves.
4. 1st Dose Fill the tanks by ½ to 1 liter RXSOL-20-2030 per ton of water through pipe or main hole, for 75-80%
  of capacity of tank to be cleaned.
5. Then fill tank to 25% capacity with sea water, raise the temperature up to 60°C maximum, and maintain this
   temperature for 24 hours. 
6. Top up tank to 75-80% capacity with sea water, continue to heat for 48 to 72 hours.
7. Discharge and strip tank. Fill to 50-60% capacity with sea water and allow 2 hours rinsing time.
8. Discharge tank and strip, flushing tank with sea water  for 2  hours,  stripping  continuously.  When  
  completed, inspect tank to ascertain if second cleaning is required. If so:
9. For completion add second dose of RXSOL-20-2030, fill tank with sea water 75-80% capacity and raise the
   temperature to 60°C maximum. Maintain this for 48 to 72 hours. And recalculate the solution.
10. Discharge and strip tank, flush with sea water, stripping continuously for 2 hours. 





Dual HD Cleaner

Dual HD Cleaner


Item Code: RXSOL-20-2012-025

Introduction:-
Heavy Duty Blend of liquid cleaner, Organic Synthetic detergent and Emulsifying solvents, which makes economical  to use and highly effective on heavy deposition of  many soils . A very strong cleaner, which can be used to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, Tung oil etc.  It is low toxic product with an exceptional solvency power on soil & oily matter. It  is  free  from  Hydrocarbon  solvents, Biodegradable and minimizes the extreme hazards to personnel in handling materials.

Fields of Application:-
Highly  effective cleaner for cleaning of tanks, bilges, tank tops, animal oil, vegetable  oil,  and  grime  are  rapidly emulsified  with  this  chemicals.  in  factories   for  cleaning  machinery ,  manufactured  parts,  engines,  motors, conveyors, floors, and floor plates,  machinery spaces etc. By contractors  for  cleaning  road  building  machinery, scrapers, mixers, bulldozers, cranes, trucks, equipment, etc. Dirt oil, grease, animal oil, vegetable oil, and grime are rapidly emulsified and rinsed away from aluminum, brass, steel, cast, iron, chrome plate, porcelain, glass, painted surfaces, stone, cement and wood.

Application:
Materials consumption and Using procedure is completely depends up on NATURE of  materials going to clean.

Using Procedure:
First of all flush the system with cold water to prevent evaporation  rates  and  polymerization  then  the  most economical method of using RXSOL 20 2012  is by direct injection followed by recirculation washing, using tank cleaning machines.

Spraying Method:-
Using RXSOL 20 2012 as delivered in drums, spray onto areas where residue remains  following  rough  washing leave for 10-45 minutes (but do not allow to dry), then Butterworth at maximum pressure and warm water  60oC for at least 3 hours, checking that there is no foam remaining in the final stages.  Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.

Re-circulation Method:–
Fill tank with fresh water and heat up to warm 50oC .  IF a drop line is available on the tank line  system, then start to circulate the water and add the required amount of Caustic flakes ( if required )  and RXSOL 20 2012 to make a 0.5%  to 2.5% solution.  A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank.  Under normal  circumstances, between 2.5% and 4.5% will be sufficient strength.  If there is no drop line, then lower Butterworth hoses  into  the  tank  from  the pump stack header without machines attached and circulate through  these  hoses  while  you  fill  the  solution material.

Gel method:
Use 0.5 kg. RXSOL TC 1001 semi solid gel  to  5 liters Of RXSOL 20 2012. , mixture becomes gel  , which can be applied on heavy deposited vertical area for  20-30 minutes , then finally   Rinse  with  high  pressure  water  for removal of  solid soils . Handling: Non-flammable, non-explosive, and non-toxic. RXSOL 20 2012  will  cause  eye irritation and possible allergenic sanitation if it comes in contact with the eyes. Avoid contact with skin and do not get in the eyes.





Edgesol

Edgesol


Item Code: RXSOL-16-3014-025

Product Description:-
RXSOL-16-3014 is a superior Heavy duty and highly concentrated water based alkaline cleaner, containing specially selected detergents and powerful long chain organic syndet, specific salts with surfactants  &  wetting agents. It is low toxic product with an exceptional solvency power on soil & oily  matter & having good  foaming  qualities. It  is  free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling  materials. Also suitable for TANK CLEANING .It can be used as a general purpose cleaner to remove oil and grease deposits.

Using Procedure:-
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-16-3014 is by direct  injection  followed  by  recirculation  washing, using  tank cleaning machines. Spraying method: Directly spray on the contaminated area and let it act for 5-10 minutes. Then clean the system  under high pressure. A solution of 5-10% in fresh water can be used for this  purpose  also , and may be sprayed on and hosed off using high pressure.

Circulation method:-
Cleaning the oil side of  tank can be cleaned by circulating through with RXSOL-16-3014. 

Rock and Roll method:-
fill the tank with water (fresh or sea) up to 25 - 30% of its volume then 5–20%  (Depend  on  contamination) RXSOL-16-3014 will add , let it stand for approximately 12-24 hours. Then fill with more water to 90% of the tank's capacity. This way the tank will be cleaned by natural agitation due to wave motion. Let for a few days, then drain the tank and ballast- de- ballast  2-3  times  in  order  to  achieve  complete  and  thorough  rinse off.   

Characteristics:-
Removes grease, oil, carbon deposits, soil and  grime.Keeps  loosened  deposits  in suspension preventing  re-deposition. Low toxic.  , Non-flammable. Free from hydrocarbon  solvents.  Effective  and  econ  omical  in  use , Water-based cleaner. RXSOL-16-3014 has numerous cleaning applications including removal of greases, waxes, oil, sludge, soot, carbon deposits and general dirt and grime . Non-corrosive to ferrous metals.  Suitable for all tank-coatings. Can be used for gas and hydrocarbon freeing of tanks. Can  be used  for deodorizing  Contains wetting agents. Suitable for accommodation cleaning of wood work, leather, desks, etc.


            





Sodium Dichromate

Sodium Dichromate


Item Code: RXSOL-20-2400-025

Sodium Dichromate:-
After thorough cleaning, the stainless steel part is ready for immersion in a passivating acid bath. Any one of three approaches can be used--nitric acid passivation, nitric acid with sodium dichromate passivation and citric acid passivation. Which approach to use depends on the grade of stainless steel and prescribed acceptance criteria.
More resistant chromium-nickel grades can be passivated in a 20 percent-by-volume nitric acid bath . As indicated in the same table, less resistant stainless grades can be passivated by adding sodium dichromate to the nitric acid bath to make the solution more oxidizing and capable of forming a passive film on the surface.
Another option, used in place of nitric acid plus sodium dichromate, is to increase the concentration of nitric acid to 50 percent-by-volume , The sodium dichromate addition and lit : higher nitric acid concentration both reduce the chance of undesirable flash attack.

APPEARANCE : Odorless orange crystal grain
Na2Cr2O7· 2H2O : 98.0% min
SULPHATES : 0.4% max
CHLORIDES : 0.2% max

Application:
• Chromium source in preparing chromium compounds
• Leather tanning and screen printing
• Electroplating
• Pyrotechnics and explosives
• Pigment preparation
• Wood Preservative
• Metal Treating and corrosion inhibitor
• Oil drilling
• Catalyst for the chromium metal production
• Photographic engraving

Note:
10588-01-9 (Anhydrous)
7789-12-0 (Dihydrate)





Sodium Hypo Chlorite

Sodium Hypo Chlorite


Item Code: RXSOL-31-3025-025

Sodium Hypo Chlorite:
A 12% solution is widely used in waterworks for the chlorination of water and a 15% solution is more commonly used for disinfection of waste water in treatment plants. Hightest hypochlorite (HTH) is sold for chlorination of swimming pools and contains approximately 30% calcium hypochlorite. The crystalline salt is also sold for the same use; this salt usually contains less than 50% of calcium hypochlorite. However, the level of active chlorine may be much higher.

HANDLING AND STORAGE PRECAUTIONS:
Do not store adjacent to chemicals that may react if spillage occurs. Comply with Oman regulations, when shipped. If closed containers become heated, vent to release decomposition products (mainly oxygen under normal decomposition). Do not mix or contaminate with ammonia, hydrocarbons, acids, alcohol or ethers.

DO NOT REUSE CONTAINERS:
Product residues may remain in containers. All labeled precautions MUST be observed. Dispose of container in a manner meeting government regulations.

PRODUCT DISPOSAL:
Product should be completely removed from containers. Material that cannot be used or chemically reprocessed should be disposed of, in a manner meeting government regulations.

Precaution:
A weak soln. ( 1.2 % ) is used.For purifying water 0.02 to 0 .2 % volumetric is sufficient for Potable Water Treatment.





Alkaleen Liquid Heavy Duty

Alkaleen Liquid Heavy Duty


Item Code: RXSOL-20-2005-25

Product Description:
RXSOL - 20 - 2005 - HD is a superior Heavy Duty and highly concent rated Alkaline Cleaner, containing specially selected detergents and powerful long chain organic syndet , specific salts with surfactants & wetting agents .It is low toxic product with an exceptional solvency power on soil & oily matter & having good foaming qualities. It is free from Hydrocarbon solvents, Biodegradable and minimizes the extreme hazards to personnel in handling materials. It is suitable for TANK CLEANING used For cargo hold cleaning after coal and pet coke exceptional solvency power on soil & oily matter & having good foaming qualities. It is free from Hydrocarbon solvents, Biodegradable and minimizes the extreme hazards to personnel in handling materials. It is suitable for TANK CLEANING used for cargo hold cleaning after coal and pet coke.

Using Procedure:
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2005-HD is by direct injection followed by recirculation washing, using tank clening machines.

Spraying method:
Directly spray on the contaminated area and let it act for 5-10 minutes. Then clean the system under high pressure. A solution of 5-10% in fresh water can be used for this purposealso , and may be sprayed on and hosed off using high pressure. Circulation method : Cleaning the oil side of tank can be cleaned by circulating through with RXSOL-20-2005-HD.

Rock and Roll method:
Fill the tank with water (fresh or sea) up to 25 - 30% of itsvolum e then 5–20% (Depend on contamination)RXSOL-20-2005-HD will add ,let it stand for approximately12-24 hours. Then fill with more waterto 90% of the tank's capacity. This way the tank will be Cleaned by natural agitation due to wave motion. Letfor a few days, then drain the tank and ballast- deballast 2-3 times in order to achieve comple-te andtho- ugh rinse off.





All Purpose Cleaner Tech

All Purpose Cleaner Tech


Item Code: RXSOL-15-1037-210

All Purpose Cleaner Tech:-
It is a alkaline buffer cleaner containing corrosion inhibitors to prevent the corrosion of metals . Can be used for all types of cleaning and degreasing and may be applied by brush ,  hand spray , high and low pressure washing machines etc. Leave surface residue free.

Application:
For cleaning engine parts like fuel and lube oil filters , injection nozzles , pump parts , inlet and exhaust valves and cleaning of hard surfaces , such as deck , tanks , engine - rooms , etc

Dose:
Depending on contamination 50 - 200 ml per 10 litrs of water . i. e. 200 mol to a bucket of water .





Dechlorination Soln De Hypo

Dechlorination Soln De Hypo


Item Code: RXSOL-20-2021-025

Description:-
RXSOL ORG DICHLOR Mixture of Emulsifier, new  technology  OXIDIZER , Corrosion  inhibitors, Rust  preventive. due to free from  caustic  and Hydrocarbon very  gentle on hands & ideal  for  cleaning Walls Wood works, Metals and all areas . Acts as superior quality cleaner / degreaser.

**These products become more aggressive with temperature increase, and should not be allowed to dry on tank walls or stored in cargo tanks as cleaning solution or slops. 

Bleach will -
• Remove odors.
• Remove color.
• Improve permanganate time

praying:-
Following rough washing to a good Water White or better, apply dilute RXSOL ORG DICHLOR to 1 - 3% strength.  First wet the tank surface (spray with DI water), then spray all  over  with  Bleach, wait 30 minute (but do not allow to dry) and then rinse very well with DI water, including the tank top towards the sump.  To ensure that you have covered all areas properly, this process should be carried out at least twice with good DI water.

Re-circulation:-
Following rough washing  to a good Water White standard or better, apply  dilute  RXSOL  ORG DICHLOR  to 1-3% strength.  Mix sufficient Bleach with fresh water  in  the  tank and heat  this mixture to 40 - 50 0 C, circulate  through  the  drop  line  if  fitted  and  than circulate through butterworth machine for 3 hours.  After re-circulation immediately warm butterworth to (500 C) the tank for 3 hours at maximum pressure, increase the water temperature to 80-85 o C after 45 minutes.  Check (by smell) that there is no Bleach remaining, then fresh water rinse and dry.





HCF Remover

HCF Remover


Item Code: RXSOL-20-2007-25

Product Description:-
RXSOL-20-2007-210 is a  very  strong low foaming cleaner, Especially formulated to  soften  up / remove  baked  on  drying oils and  also  used after animal  and  vegetable  oils,  fish  oils, tall
oils,tug oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter .It is free  from  hydrocarbon  solvents  and minimizes  the  extreme hazards to personnel in handling materials.

Application:
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2007-210 is by direct injection followed by recirculation washing, using tank cleaning machines.

Note:
Tank Lining– Stainless / Epoxy / Phenolic / Zinc-silicate.





Latex Remover

Latex Remover


Item Code: RXSOL-20-2040-025

Latex Remover:-
Rxsol Latex Remover is very strong cleaner to remove various type of latex and latex films. It is free from hydrocarbon solvent and it is biodegradable.

Application:
Use for Tank cleaning of Cargo tank, Tank Container and Storage Tank. Also use in workshop as a stripper to clean the lates from floor.

Dose:
1.  Butter worth the tank after discharge without any delay for 2 hours with warm fresh water and inject from the beginning on the RXSOL  LATEX  REMOVER.  Make  the  solution  of  Rxsol  Latex Remover  4-10% with water for tank cleaning procedures. Allow product to soak for 20 minutes and flash down with fresh water. Same for circulation method where time for circulation could be between 1-3 hours. An additional circulation could be necessary when  deposits  of  Latex  are  quite  heavy . Spray RXSOL  LATEX  REMOVER  at  ambient  temperature  and  allow  approximately  20  minutes activation time. The latex can then be removed with  cold  water  by  means  of  high  pressure.  If necessary, repeat this treatment.

2.   Ventilate, mop and dry the tank. Some minor dried latex residues which could be present on heating coils and pump body have to be removed manually.Recommended preparations before loading and discharge of Latex: Prepare the loading/discharge connection directly at the pump stack of the respective tank and flange off the line to the manifold. Install a valve at this connection  and use hoses for the shore connection (necessary length should be as short as possible). Close the drop line inside the tank by a flange or alternatively with wooden plug.If a plug has to be used cover this with plastic foil (at least 3 layers) and fix it with a stainless steel band. For loading and discharge use the deep well pump only. All other connections and openings inside the tank should   be dismantled, flanged off or protected as described above (e.g. steam, nitrogen,vapour line connections etc.).Fixed tank cleaning machines should be dismantled and blinder flanged. Tank dome hatches and Butter worth hatches including gaskets should be protected with a plastic foil which has to be placed between the dome and the hatch. Before loading steam the tank with very low pressure (1 bar) to make sure that the bulkheads, tank  top, bottom and the lines inside the tank are humid but avoid any heat up. All equipment that might come into  contact with the Latex should be washed with fresh water so they are humid before the loading takes place. Load the tank 100% and into the tank domes to prevent that the Latex comes into contact with air during the voyage.During loading the vessel must be therefore trimmed and kept on even keel to prevent air pockets in the tank. Before discharge remove the plugs of the vapour connection and steam connection and flush all equipment that might come into contact with Latex with fresh water During discharge keep the tank closed tokeep the humidity.





ORG - 8 Cleaning Chemical

ORG - 8 Cleaning Chemical


Item Code: RXSOL-20-2061-210

Description:
Cleaner for zinc and epoxy based tank coatings.
ORG -8 will clean and upgrade coated cargo tanks after cargoes such as leaded gasoline, gasoline blends containing MTBE, carbon tetrachloride, methylene chloride as well as virgin naphtha.It will in a cost effective way remove lead, hydrocarbons, chloride, sulphides  etc.  from  the  pores  of  zinc silicate and epoxy coatings. It has been designed with  a  pH  value  of  5.5 for safe application on these types of cargo tank coatings.

The ordinary cleaning  method  with  a  synthetic  soap  takes  a  long  time  and  is  insufficient  in removing the described contaminants. A week acid solution in combination with synthetic soap gives a much better cleaning result.

ORG -8 is used as a final cleaning procedure when the cargo tanks have to  be  completely  free  of lead, chlorides, sulphides or MTBE prior to loading of special high purity cargoes.

Application:
Cleaning of cargo tanks after cargoes of leaded gasoline,  gasoline  blends  contaning  MTBE  & Virgin Naphtha.

Dose:
HAND SPRAYING METHOD
1. Apply 1 litre undiluted ORG -8 per /10-15 M2
2. Let the cleaner penetrate for 30-45 minutes
3. Wash down with freshwater and check results preferably with a wall wash test kit.

RECIRCULATION METHOD
1. Make a 10% solution in freshwater in a slop (solution) tank.
2. Heat the solution to a maximum of 60.C.
3. Wash tanks by recirculation for 60 minutes.
4. Usually one solution is used for washing 3-6 tanks
5. Rinse with freshwater and check the results
6. For chloride-free cleaning and passing chloride test use chloride-free De-Ionised Water for
    the final rinse.

Note:
APPLICATION, FEATURES & BENEFITS1. Cleaning of cargo tanks after cargoes of leaded gasoline, gasoline blends contaning MTBE &
    Virgin Naphtha.
2. Biodegradable
3. No hydrocarbon solvents
4. Safe to use on epoxy coatings.
5. Safe to use on zinc silicate coatings.





Phenol Cleaner

Phenol Cleaner


Item Code: RXSOL-20-2047-210

Phenol Cleaner:-
Direct after discharge flush lines and tanks thoroughly with hot fresh water or demi water and recirculate. This is done to bring the freezing point down prior to the prescribed tank cleaning procedure. Demi water will be used if the pre-wash quantity can be pumped ashore.

1) Butterworth the tanks 1, 5-2 hours with hot seawater or freshwater (80°C).

2) Prepare the following cleaning solution in freshwater:0.4 % RXSOL CTC-VOLC  Butter worth the
    tank 1 hour by recirculation with a temperature of approx 70°C. The necessary temperature can
    be achieved/maintained by means of heating coils, or  going via the Butter worth heater. The
    solution can be used for 1 to 4 tanks. 

3) Butterworth the tank for 0, 5 hours with hot fresh water.

4) Ventilate, mop and dry the tank.

5) Instead of recirculation cleaning the RXSOLCTC-VOLC can be as well injected into the
    Butter worth system (see cleaning method 3).





RXSOL 666

RXSOL 666


Item Code: Rxsol-20-0666-025

RXSOL 666:-
Rxsol 666 is surfactant base highly concentrate Product specially designed to clean Tank Container , Cargo Tank which are carrying Heavy Aromatic , hydrocarbon solvent and, natural Latex etc. Rxsol 666 due to strong concentration provides a quick penetration and powerful reaction to remove stubborn hydrocarbon and other organic deposits, from all type of surface. It is ideal Product to Clean Tank container, cargo Tank , latex Surface etc.

Dose:-
Rxsol 666 is covering 10-12 squire meter are when spraying directly. It is advised to use a solution of 2-5% wash water mixed in the tank to be cleaned. Dose rates and results will vary depending on contamination, the temperature of the cleaning solution, and number of tanks to be cleaned with the solution.

Spot cleaning:-
Rxsol 666 can be sprayed neat onto tank surfaces to be cleaned. The contact time should be
at least 30 minutes. Bulkheads/walls can be washed down by use of tank washing machines
or high pressure cleaning machines. The best result is achieved with warm water. Slops
should be constantly stripped from the tank and transferred to a holding tank or pumped
ashore to slop tanks.

Rock and Roll method (Cargo Tank):-
1) Cleaning of double bottom tanks during voyages.
2) Flush tank with sea water, stripping constantly.
3) After flushing, ensure all suction and discharge valves in the engine room are closed.
4) Dose tank with Rxsol 666 through the sounding pipe or manhole between
0.5 - 1 litre per ton of water, for 75-80% of capacity of tank to be cleaned.
5) Fill tank to 25% capacity with sea water, raise the temperature up to 60°C and maintain this
for 24 hours.








G 50 Marine

G 50 Marine


Item Code: RXSOL-20-2026-025

G 50 Marine:-
A very strong alkaline cleaner, which can be used to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, tung oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter.It is free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling materials.

Application:
Liquid water based strong alkaline cleaning agent suitable for Tank Cleaning.

Dose:
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-G 50 Marine is by direct injection followed by recirculation washing, using tank cleaning machines. Spraying Method - Using RXSOL-G 50 Marine as delivered in drums. Make the solution 0.5 to 5% concentration and spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks and if desired result has been achieved fresh water rinse and dry.

Future and Benefit:-
· Liquid water based strong alkaline cleaning agent.
· Rxsol G 50 Marine is a very suitable tank cleaning agent.
· Removes oil, fats, fatty acids and mineral pollution.
· Suitable to use on additives (pure).
· Also used on chemical contamination in tanks.
· Suitable on ferro metals and stainless steel.
· Rxsol G 50 Marine is easily washed out of tanks.
· Can be used with sea water
· Rxsol G 50 Marine contains a water-hardness stabiliser





Lube Oils Cleaner

Lube Oils Cleaner


Item Code: RXSOL-20-2050-210

Lube Oils Cleaner:-
Rxsol Lube Oils Cleaner is a multi purpose product that can handle several different applications as well as solve and clean complex contaminations. Rxsol Lube Oil Cleaner removes lube oil,oil mixed with hard deposit, like rust and lime. Rxsol Lube Oil Celaner can also remove deposits from glycol and similar products.

Application:
Rxsol Lube Oils Celaner can be used for cleaning of lube oil, Lube and fuel oil separators, heat exchangers , Lube oil Tanks and pipe systems. Rxsol Lube Oil Celaner can be used for manual cleaning and Cleaning In Place with cleaning equipment.

Dose:

Manual Cleaning:-
For manual cleaning of separator parts and machinery parts.Make a solution between 5-20% concentration depending on how dirty Tank and equipment to be cleaned is. Both oil and lime will be solved with time, let soak for at least 2 hours. After 2 hours the parts can be cleaned using by High Pressure Machine rinsing or brushing.

Cleaning In Place of Separator:-
For the lube oil separator use a 20% solution
For the fuel oil separator use a 10% solution

Recommended cleaning temperature is 70-90oC (158-194oF). A normal cleaning cycle is between 1 to 3 hours depending on the dirtiness and character. If the separator has very hard deposits the cleaning cycle may have to be repeated with new cleaning fluid.

Lube Oil Tank:-
• Instead of recirculation cleaning the RXSOL Lube Oils Cleaner can injected into the Butter
worth system . Kindly make the solution 0.5 -5% and inject same. Depending on the tank
size and height fill the necessary amount of freshwater or seawater into the service
tank .
• Butter worth all tanks to be cleaned 1-1,5 hour using the water from the service tank .
• Heat the water by means of heating coils, cargo heat exchanger or going via the Butter
worth heater.
• The pre-cleaning temperature should be between 70 and 80°C.
• Pump the waste water from the tanks to be cleaned back to service tank (overtop).





Marine Clean SC

Marine Clean SC


Item Code: RXSOL-20-2010-025

Product Description:-
Marine clean SC is is a superior NON- CAUSTIC BASED cleaner which is developed for use in TANK and other systems containing aluminium and other soft metal. It is also novel blend of organic and inorganic corrosion inhibitors, including molybdate, intended to protect steel, copper and other nonferrous metals. RXSOL-20-2010-210 strong non-caustic surfactant basis Tank cleaning and degreasing Product. It is based on the latest and most powerful biodegradable Surface Active and emulsifying agents. It contains fatty alcohol  etoxylates, metasilikates and complexing agents. It works well in hard, soft, ambient and hot water. It is ideal for soot removing and cleaning of extremely dirty tanks after Mineral Oils/Petroleum Products. Note. All cleaning chemicals have reduced effect with seawater.

Application:-
1) Non-Flammable.
2) Leaves no film in the cargo tanks.
3) Easy to apply.Effective ande conomical in use.
4) Suitable in sea & fresh water.
5) Contains no ethoxylated nonylphenol (NF).
6) Biodegradable.

Dose:
Prior to use of any chemicals, make sure the tanks and lines are well stripped and drained. A proper pre-cleaning will reduce the amount of chemicals required. Further, do not overheat as this may change the characteristic of the cargo and in some cases burn the cargo to the bulkhead. Carefully read the cargo specification.For vegetable, animals, and fats: Tanks containing drying or semi-drying oils should be flushed or pre-washed or moisten as soon as possible After Completion of discharging to prevent formation of hard tenacious residues. The temperature used for precleaning will depend on whether the cargo is drying, semi-drying or non-drying, and the cargoes melting point. Thus an individual cleaning operation should be made for each cargo.

Due to the fact that the zinc is porous, a prolonged precleaning with lower temperatures is highly advisable prior to introduction of chemicals on such lining.

Re-circulations:
1) Flush tanks with ambient seawater to remove remaining cargo to slop. (As per MARPOL 78/73).
2) Recycle tanks with increasing temperature for 2-8 hr, depending cargo and size of tank. This is a very important operation, as it will   
     remove oilymud and residues in the coating/steel.
3) Make a mixture with fresh water and 0,5 -2 % Marine clean SC. Insert the mixture into the tank and commence the re-circulation
     wash for 2-8 hr. Increased temperatures will improve the cleaning result. Maximum effect from chemical at 650C. Do not overheat, 
     as this may burn the cargo.
4) Flush tanks with large amount of warm seawater (2-3 hr) to remove any residues of Chemicals.
5) Flush tanks with freshwater to remove salts,mop and dry.

Spot cleaning after most CPP / hydroc- hydrocarbons.
1) Marine clean SC may be sprayed on the bulkhead neat or diluted , to areas where residues remain after tank washing,“Spot 
     Cleaning”. A heated dilution is found to be very efficient.
2) Product should be allowed to stand for 10-30 minutes prior to re-washing areas. Do not leave the product to dry on bare coating.
3)  Clean areas by flushing manually with high pressure, using fresh water, or by performing a re-circulation. For
     persistent deposits, agitation by scrubbing will assist the cleaning operation. Heated water will increase the cleaning effect . 





Metalic Brightner Eco Rust Clean

Metalic Brightner Eco Rust Clean


Item Code: RXSOL-20-2054-210

Metalic Brightner Eco Rust Clean:-It is a superior heavy duty and highly concentrated liquid blend of surfactants & organic compounds containing rust penetrating agents , solubilizer and inhibitors. Acts as rust proofing agent before the application of paint  or  coatings. It  is  non-flammable.  Prevents further rusting.

Application:
Specially designed for removal of rust from any steel surface area and  rust  stains  from  brass, copper, stainless steel, aluminum, wood and ceramic surfaces. Also acts as a surface brightener.

Dose:
It should be applied in full concentrated for heavy stains, or diluted with 20-50% with fresh water for light strains.





Moya Oil

Moya Oil


Item Code: RXSOL-20-2023-025

Moya Oil:-
RXSOL MOYA OIL is effective and  economical emulsifier. Safe to use on most metal surfaces, painted and coated surfaces and also used as a multipurpose degreaser in extremely hard cleaning conditions.

Degreaser Moya oil
Specification:
Colour Redish Yellow
appearance homogeneous clear.
Odour- Citrus
PH value- 8.50 - 9.50,
Viscosity- Ford cup B-4-12 seconds at 22 Deg.c
Specific Gravity - 1.042-055.
Non flammable, Non Toxic, Non Caustic, Non Explosive and causes no pollution.

Application:
RXSOL-20-2023   is    applied   by   Spraying ,  Brushing,  Soaking,   Dipping ,  Rubbing,   or     Mopping Spraying  is  used for cold cleaning  interiors of oil storage  tanks or  where surfaces to  becleaning   interior  or oil  storage tanks or  where surfaces to be cleaned are irregular. After spraying  RXSOL-20-2023 should  be allowed  to remain for 10 to 20 minutes before rinsing. If  dry surfaces  is not  required it is necessary to rinse with water .Brushing and mopping is used with  RXSOL-20-2023 for removing oil from decks  piers and other large areas.

Dipping & soaking in unheated  RXSOL-20-2023 is the most economical way of cleaning small or large parts.Rubbing with a soft cloth or  sponge soaked  with  RXSOL-20-2023   is  an  easy  and quick method of  cleaning larger  parts and painted surface. Steam  cleaning can be speeded up by spraying RXSOL-20-2023 a few minutes prior to steam lancing.

Dose:
Ready to use for tank cleaning or general degreasing.

Note:
Dirt, Oil Grease and  Grind  rapidly emulsified  and  rinsed away from Aluminium,  Brass, Steel, Cast iron, Chrome  plate ,  Proceline,  Glass,  Painted  surfaces,  Stone, cement  &  Wood  The ingredients incorporated in RXSOL-20-2023   has  a much more efficient function . Particles  of  soil and oil are rapidly reduced to colloidal size by this interfacial action and thereby moreeasily emulsified and washed away fresh or salt water having cleaned metal surface.


 





Nitric Acid 62 to 68

Nitric Acid 62 to 68


Item Code: RXSOL-20-1106-25

Product Description:
Extra pure NITRIC, removes iron residue & forms an oxide layer that boosts the corrosion resistance of the stainless steel intended to improve the corrosion resistance of parts  made from austenitic, ferritic and materialistic corrosion resistant steels of the 200, 300 and 400 series and precipitation hardened corrosion-resistant steels.High carbon, high chromium materialistic 440C grades which are selected for high hardness and resistance may be exempt from passivisation treatments at the discretion of the procuring activity.

PRECAUTION:
Loose iron particles or other foreign particles must be removed or they will appear as rust or stain spots. May become smeared over or imbedded into the surface of corrosion-resistant steel parts.

DO avoid chlorides that, in excess, can Cause a harmful flash attack. When possible,Use only a good grade of water containing less than about 50 parts per million (ppm) of chlorides. Tap water is usually adequate, and in some cases up In several hundred ppm chlorides can be tolerated.

Application:
Transparent, colorless or yellowish corrosive liquid. A strong oxidizing agent that will attack allmost all metals. Hazard: Dangerous fire risk in contact with orgenic materials. Highly toxic by inhalation, corrosive to the skin and mucous membrane.

Note:
During processing operations such as forming, machining, tumbling and lapping, iron particles or other foreign particles may become smeared over or imbedded into the surface of corrosion-resistant steel parts. These particles must be removed or they will appear as rust or stain spots.High carbon, high chromium martensitic 440C grades which are selected for high hardness and resistance may be
exempt from passivation treatments at the discretion of the procuring activity.





Rxsol Org-6

Rxsol Org-6


Item Code: RXSOL-20-2059-025

Product Description:-
RXSOL-20-2059-210 is an all purpose degreaser for cleaning of Oil and Sludge with emulsifiers. It is an excellent blend of powerful solvent base and  emulsifying  inorganic  products . Specially  designed   for engine room and cargo  tank cleaning .Main feature of RXSOL-20-2006-210 is, it finally  dissociate  slop emulsion  to  separate  oil  and  water .This  provide  us with ability to dispose o f waste  solution as per MARPOL & IMO rules and regulation.

Dosage:-
 Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended, where as medium contamination dilute 1:10, and for heavy contamination neat rxsol-20-2059-210 is suggested to use.

Procedure of use:-
RXSOL-20-2059 is recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-2059-210 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for at least 3-5 hours before passing through an oily water separator.

Tank Cleaning  Sludge/ Lube Oils / Slope-Black Oil:-
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2059-210 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2059-210 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.





PH Booster

PH Booster


Item Code: RXSOL-40-5024-025


PH Booster:-
RXSOL pH Boosters are liquid  alkaline formulation,used as alkalinity source for boiler feed water. It is synergized with properties of pH boosting and water conditioning.

Dosage and Method:-
Rxsol pH Boosters are dosed depending upon the feed water characteristic and alkalinity requirement. It is compatible with all other treatment chemicals. It is dosed  exactly  as  per  the  dosage  rate  and method of RXSOL-50-5001.
Please refer to your CSL service engineer for exact product dosage.

Key Features & Benefits:-
Minimizes corrosion of feed water tank, lines and pump
Imparts water and sludge conditioning to minimize scaling and deposition
Compatible with other treatment Chemicals
Completely biodegradable chemicals





Tank Clean

Tank Clean


RXSOL TC 2001 is highly concentrated organic/inorganic emulsifier with powerful penetrating agents, corrosion inhibitors and surfactants. Quickly removes oil, grease, gimres, adhesive and dyes. Best results also achieved forcleaning of oil side of fuel and lube oil heat exchangers.

APPLICATION:  Used as a tank cleaner or for general degreasing, cleaning and gs freeing for double bottom tanks, wing tanks, pipe lines, fuel oil tanks, etc.

DOSE:  Refer to technical datasheet.


PACKAGING: 25 ltrs, 210 ltrs





Secleaner

Secleaner


RXSOL SC 2002 is a liquid blend of concentrated emulsifier with detergetns. Specially formulated for cleaning fuel oil double bottom tanks, deep tanks and wing tanks. Also can be used for local cleaning and degreasing of deck and engine rooms.

APPLICATION:  For cleanign and degreasing of boilers and marine diesel engines. Specially suitable for cleaning of tanks at sea where mechanical action is limited.

DOSE:  Should be diluted at the rate of 1/2 to 1 ltrs. Of concetrte to 1000 ltrs. Of water for the Rock & roll method tank cleaning, fuel oil double bottom tanks, deep tanks and wing tanks.


PACKAGING: 25 ltrs, 210 ltrs





Liquid Alkaline Cleaner

Liquid Alkaline Cleaner


RXSOL AL 2005 is a superior heavy duty and highly concentrated water based alkaline cleaner. It is free from hydrocarbon solvents. Also suitable for tank cleaning. NON-CAUSTIC ALKALINE CLEANER

APPLICATION:  It can be used as a general purpose cleaner to remove oil and grease deposits.

DOSE:  Refer to technical datasheet.


PACKAGING: 25 ltrs, 210 ltrs





Tamcks

Tamcks


we are the leading manufacturer and supplier of tamcks









Contact Us
Rx Marine International
Mr. R. Tiwari / Kiran tiwari
No. 105, A- Wing, BSEL Tech Park, Near Vashi Railway Station, Vashi
Navi Mumbai - 400705, Maharashtra, India

Contact via E-mail


Home  |  Profile  |  Our Product Range   |  Site Navigation  |  Contact Us

Member IndiaMART.com © Rx Marine International. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited