The machine is strong, sturdy and simple to operate powered by 0.5Hp Single phase motor. The drive is transferred through a reduction gear box directly transferred to a set of gear wheels to S.S. Crushing rollers.

Specifications:

The side frames are made of graded cast iron and coated with Epoxy paint for protecting from rust. The inner surfaces are lined with Stainless steel sheet to prevent rust formation. The crushing rollers are made of non magnetic Stainless Steel of grade 304, mounted on S.S. shaft supported by ball bearings/Needle bearings. The chamber area where the sugarcane is crushed is totally covered with Stainless Steel Sheets. The bottom side of the machine is with fabricated steel frame with with fibre glass sheets and finished with good paint. The top cover is of Stainless Steel sheet. The motor is controlled by a forward and reverse switch and a safe trip MCB.

Special Features:

• Stainless Steel Crushing rollers.
• Small Size – L 23 X W 23 & Ht 25(Without Stand) and With Stand 57 Ht.
• Power: Single phase 0.5HP – Very low power consumption – Required to run only when it is needed.
• Single time crushing gives maximum amount of juice.
• Totally Enclosed by S.S. covers– Protects from atmospheric dust and insects.
• Needle bearings with double protection seal- No mixing of grease and oil with juice.
• Easy to maintenance.
• Waste Disposal– prevents contact from insects
• No Noise
• Filters provided and easy to clean
• Easy to move

Technical Specifications:

• Power input: Single Phase= 220V/50Hz OR 110V/60Hz
• Drive motor: 0.5hp (500 w) 1440RPM Single phase
• Capacity of juice extraction: 60 litres per Hour (165Kgs Crushing per hour)
• Two pairs of Stainless steel 304 grade crushing rollers with FIXED gap
• Weight: 72Kgs

Our sugarcane crusher is designed to extract sugarcane juice in safe method. The machine is powered by 1 hp or 0.5 hp single phase motor. The drive is transferred through a reduction gear box directly transferred to a set of hardened steel gear wheels to S.S. Crushing Rollers.

Specifications

The inner surface of plates are lined with ss sheet to prevent rust formation. The crushing rollers are made of non-magnetic stainless steel of grade 304, mounted on S.S. shaft supported by ball bearings/ needle bearings. The bottom of machine is covered with fabricated steel frame with good paint finish. The motor is controlled by a forward and reverse switch and a safe trip MCB.

Special Features

• Size: 23" x 23" x 25" (without stand) and with stand 57" height.
• Single time crushing gives maximum amount of juice (upto 65% by weight basis) giving purity in taste. (Maximum crushing, output is 70% only- The left over 5% consists water and it will be bitter in taste).
• Enclosed by S.S. covers.
• Needle bearings with double protection seal - No mixing of grease and oil with juice.
• Waste garbage is collected in a polythene bag provided at the delivery bend.

Process:

The sugarcane is first passed through first set of rollers and then transferred to second set of rollers by a plain chute guide. Thus the sugarcane juice is extracted in safe manner. A polythene bag is tied to the outlet cover to collect the waste bagasee and can be disposed as and when it is full. This also helps to prevent entry of dust and insects.

Uses

• Useful for extracting fresh sugarcane juice.
• Suitable for all fruit juice shops and restaurants.
• Used by medicine manufacturers and by sugar mills for laboratory uses.

We are dedicated to achieve our target production with full accuracy.

Specifications

• Power: 0.50 HP. TO 15 HP
• Flow Range: 10 lpm To 2600 lpm
• Head Range: 6 mtr. To 60 mtr

Features

• No need of pump houses.
• Noiseless operation.
• No suction and priming problem.
• High operating efficiency.
• Maintenance free water lubricated bushes.
• Designed for wide voltage fluctuations.
• Highly durable water cooled rewindable motor.
• Single shaft for pump and motor ensures permanent correct line alignment.

We are manufacturing Single Phase Horizontal Openwell Submersible Pumps to meet customer's expectation.

Features

• Capacity: Single Phase 140/240 Volts, 50 Hz.
• Insulation: 2880 RPM
• Body: Made up of closed Stainless Steel or Gr. 20 Cast Iron, S.S. Shafts.
• The stator windings are made of water proof PVC coated polyester film wrapped copper winding wires.
• Silicon Lamination: M 45 Gr. The rotor lamination arfe fitted with E.C. Grade copper rods, brazed at ends with copper forged rings, aluminium pressure die cast rotors.
• Oil seal used prevent silt entry
• Axial Thrust developed by the pump is absorbed by thrust bearings

Applications

• Water Supply
• Small/Medium/Large Scales Irrigation
• Sprinkler Irrigation
• Gardening and Forestry Water Supply
• Village Water Supply
• Lawn Sprinkler
• Canal and Pond Irrigation
• Industrial Purpose

Advantages

• Easy to install
• Maintenance Free
• Heavy duty.
• Full fledged testing facilities

With our appropriate material selection and innovative production techniques, we design Single Phase Centrifugal Monoset Pumps.

Features

• Motors are capacitor start
• Run single phase induction type.
• 140/240 Volts range, 50Hz, Class'B' Insulation
• High pressure Aluminium Die Casted Rotors are dynamically balanced for longer bearing life.

Applications

• Domestic Water Supply
• Gardening & Irrigation
• Forestry and Nursery Water Supply
• Village Water Supply
• Lawn Sprinkler
• Canal & Pond Irrigation
• Sprinkler Irrigation

Advantages

• Easy to carry and install.
• Heavy duty, high efficiency, minimize power consumption.
• Monosets confirm to IS:9079:89.

With quality and customer satisfaction as our forte, we provide V-6 Submersible Pumps for 6" Borewell.

Features

• Material of construction and manufacturing tolerance are of high standard ensuring reliability and durability.
• 140-240 Volts 50Hz.
• Single Phase AC Supply
• Wet type water cooled
• Water lubricated squirrel cage induction motor
• Dynamically balanced rotor provide smooth running.
• The pumps are tested in the testing lab

Applications

• Domestic, Commercial & Industrial Water Supply
• Small/Medium Type Irrigation.
• Gardening & Forestry Supply
• Sprinkler Irrigation
• Lawn Sprinkler
• Fountains, Mines and Hotels

Advantages

• Compact design.
• Easy to install
• Can suck water upto 150 meter
• Heavy duty, high effiency, minimize power consumption

Being customer centric and quality conscious, we are manufacturing V-4 Submersible Pumps for 4.5" Borewell which are used in various applications.

Features

• Manufacturing tolerance are of high standard ensuring reliability and durability.
• 280-440 Volts 50Hz.
• Three Phase AC Supply
• Wet type water cooled
• Lab tested pumps.

Applications

• Irrigation
• Gardening and Forestry Water Supply
• Sprinkler Irrigation.
• Fountains, mines and hotels

Advantages

• Compact Design
• Easy to Install
• Suck water upto 180 Meter
• Heavy Duty
• Full fledged Testing Facilities

Justifying our position, as one of the leading names to manufacture Three Phase Centrifugal Monosets.

Features

• Material of construction and manufacturing tolerance are high standard.
• Motors are three phase 280/440 voltage range.
• 50 Hz Class 'A'/'B' Insulation
• Totally enclosed fan cooling type.
• Class 'B' varnish, High Pressure Die Casted.

Applications

• Water Supply
• Large Scale Irrigation
• Sprinkler Irrigation
• Gardening and Forestry water supply
• Canal and Pond Irrigation
• Industrial Purpose

Advantages

• Easy to Install
• Maintenance Free
• High Efficiency
• Monosets Confirm to IS:9079:89

Being customer centric and quality conscious company, we offer Three Phase Open Well Submersible Pumpsets.

Features

• Three phase 280/440 volts
• 50 Hz, Cat 'B' Insulation, 2880 RPM
• Body is made up of closed stainless steel
• Stator Windings are made of water proof PVC Coated Polyster film.
• Dynamically balanced rotors to provide smooth running.
• Axial thrust developed by the pump is absorbed by the two way acting thrust bearings.

Applications

• Water Supply
• Irrigation Purpose
• Sprinkler Irrigation
• Forestry Water Supply
• Village Water Supply
• Lawn Sprinkler

Advantages

• Easy to operate.
• Easy to install.

Our Coconut Trimming Machines are powered by 1Hp /440Volts/ Three Phase/ 50Hz/ Motor.

Production of Coconuts trimming per hour: About 50 to 80 Nos.

Frame Structure: Fabricated of Hot rolled Steel Frame with side and top covers of S.S.202 grade to prevent rust formation.

Head Stock and Revolving, Quick operating Tail Stock assemblies mounted on the Steel Frame. Motor controlled by a Forward & Reverse Switch. (Additional back up DOL Starter and Switch Fuse units to be provided by the buyer for the safety of the Motor).