We offer Power Control Centres that are customized according to our valuable clients. Manufactured with the maximum rating of 4000A under various ratings. These are available with switch boards in fixed and semi-draw out configuration which defines single front design.

Technical Specification:

• The operational voltage of these control centers is 415V in 3 phase 4 wire distribution system.
• Ambient temperature is 40 degree Celsius.
• Insulation voltage is 660V.
• Withstand capacity for short circuit is 50KA.
• Available form of separation is IS 8623, form 4.
• Degree of protection is according to the specifications of IP:52.

We offer designing and manufacturing of Motor Control Centers or MCC that have great capacity to tolerate larger loads. Our range of MCCs are available with multiple power stabs that helps in supporting high capacity industrial motors. These MCCs are available at industry's leading rates. These MCC units comprise:

• Full voltage non-reversing and full voltage reversing starters
• AC variable frequency drives
• PLC I/O chassis
• Solid-state motor controllers
• Lighting panels
• Transformers
• Analog or digital metering
• Feeder circuit breakers
• Feeder fusible disconnects

With auto-manual options, we offer a wide range of customized control Desks panels. The control desks are used to control the operation of individual machinery or plants. Our range of Control Desks are designed as per international rules and norms and are customized as per clients requirements.

We offers APF Automatic Power Factor Control Panel used for low tension & high tension factories and windmills. These panels are designed with the state of the art technology to suit the environment of the industry. The entire panel fuses and highly reliable in maintaining PF. We have the facility to manufacture these in different shapes like one sided, double sided and desk type. These panels are made using careful wiring and are used for the below mentioned machines:

• Automatic Control Panels for Granite Cutting Machines
• Control Panels for Rubber Extrude-rs
• Control Panels for PVC Extrude-rs
• Automatic Control Panels for Tyre / Tube Curing Presses
• Control Panels for Gantry and EOT Cranes
• DC Drive Panels for Sugar Mills
• AC Drive Panels for Power Plant Boards

We offer exclusive distribution boards that helps in protecting electrical appliances from overload voltage and current.

Features:

• Distribution system is suitable for circuit of AC 50/60Hz, rated voltage up to AC 660V, rated current up to 125A.
• Distribution control of modern buildings such as large office mansions, hotels, commerce departments, industrial and mining enterprises.
• It can protect electrical appliances from overload voltage and current.
• It also can shorten frequent switch ON/OFF under normal operation condition.
• It is one of the most reliable general distribution systems in the world.

We offer Feeder Pillars that are perfect for outdoor use and are widely applicable in different non-industry and industrial applications. Our specially designed pillars are made as per the requirements of the clients. We are achieving accurate results in our production by mixing variety of resources in our manufacturing process. These feeder pillars are extensively used in:

• Hotels
• Residential Complexes
• Townships

We are pioneer in Design, Engineering & Manufacturer of various types of Bus Ducts and Bus Trunking Systems that are available up to 4000 A, which can be operated with less than 35 degree Celsius Temperature Rise over an Ambient of 40 degree Celsius. Their short circuit withstands capacity falls at 50kA. The non-segregated Bus Ducts with inter leaving design are aptly designed for indoor and outdoor installation with IP: 55 degree of protection. All our bus duct systems are tested.

We offer various kinds of bus ducts such as:

• Super compact
• Sandwich type bus duct
• Super compact, resin cast IP 68 bus duct
• Can-allies system for lighting & low power distribution ranging from 40 Amp. to 120 Amp.

We undertake designing and manufacturing of AMF Panels (Auto Mains Failure) panels that are used for managing DG sets. Our panels have built-in safety features for protecting the Engine & alternator. They are manufactured up to 1250 KVA and are fabricated from 16 SWG thickness, high grade CRCA sheet steel. The good quality raw material made our panels dust & vermin proof. We offer powder coating for longer shelf life. A separate battery charger for continuous charging of batteries in trickle/boost mode to ensure prompt starting of the engine.

Features

• A power circuit consisting of contractor, MCB and fuses.
• Automatic start/stop of the gen-set in case of AC mains failure and its restoration respectively.
• Manual start/stop facility also provided.

Logic
Mains Failure: 3-attempt engine cranking after mains failure otherwise the engine fails to start. Engine starts-up within 10 sec of mains failure otherwise 2 more start pulses after every 10-15 seconds.
Unhealthy Mains: Any of the phase failure or voltage drops below set value.
Mains Restoration: Engine keeps running for 30 seconds before stopping, as recommended by the Engine manufacturer.

Metering

One Ammeter with CTs & selector switch, one frequency meter, one voltmeter with selector switch and one hour meter.

Set of indications

• Load on DG
• Load on mains
• Fault indications
• LLOP
• High water temp/high cylinder head temp
• Overload

Set of Push Buttons

• Engine start/stop
• Alarm acknowledge button for hooter
• Reset button for fault indication

Safety

• High water temperature
• LLOP
• Overload trip

We manufacture premium quality of Load Sharing and Synchronizing Panels that are made from high quality raw materials. These panels synchronize the different DG sets as per the load requirement of the system and if the load increases, it switches on the other DG sets one by one and synchronizes with the system automatically through PLT (Panel Logic Control) and when the load decreases below the desired level, it automatically disconnects the DG sets one by one and switches off as per the load requirement.

We offer high precision PLC panels for global giant like Siemens PLC (S7-300), MMI with ALTIWAR drive for filter press applications. This press can be operated from local/remote and auto/manual modes. Our PLC system communicates with various instruments like temperature indicating controllers, pressure indicating controllers, sensors etc.

Our main customer in this product category is Andritz Separation Ltd.

We also offer power control centers, which are manufactured from high quality raw materials. Our LT Panels comprise of the following:

• Main LT Panel (PCC)
• Automatic Power Factor Control Panel
• Power Distribution Panels
• Motor Control Center Panels (MCC)
• AC/DC Drive Panels
• Soft Starter Panels
• PLC Panels
• DG Set AMF/Synchronizing Panels
• Instrument/Mimic Panels
• Pneumatic Panels (Solenoid)
• LT Bus ducts