Scientico

Made of brass, Single action pump with oiled silk valves, cylinder 20 cm. x 3.2 cm drawplate 175 mm dia, with stopcock, and inlet screw fitted on wooden polished base

Cabinet frame of ply-board covered with sunmica from outside. Work bench top of stainless steel. Side and front door of work bench covered with acrylic. Motor & blower assembly to provide sufficient air pressure. HEPA filter efficiency 99.97% down to 0.3 micron. Pre-filter efficiency 99% down to 5 micron. Cock for gas. Front half opening collapsible acrylic door with gloves arrangement. Virus burnt out unit attachment. 20W flourscent tube light & 15/30W UV Germicidal Tube. Removable covers. With exhaust system.
CAE-35006-01 Working area size 60 x 60 x 60 cm.
CAE-35006-02 Working area size 90 x 60 x 60 cm.
CAE-35006-03 Working area size 120 x 60 x 60 cm.
CAE-35006-04 PORTABLE LAMINAR AIR FLOW FOR FIELD USE. Specially designed and developed for on field culture and analysis of specimens. MDF sturdy body with sunmica finish. acrylic covers on front & sides. front door height adjustable,

Our Audiometer Equipment Calibration Complies with - ANSI S 3.6 1989, ISO 389 1991, IEC 645, Standards for electromedical equipment.

The setup is designed to study the discharge through different notches. Set up consists of a flow channel section, supply tank, measuring tank and pump for closed loop water circulation. The flow channel is fitted with arrangement for creating jet using different interchangeable notches. It also consists a hook gauge for measuring x-y coordinates of jet and a vernier pointer to measure the height of water in channel. The flow rate of water is measured using measuring tank and stop watch provided. A Trapezoidal Notch can be tested by adjoining 2 different notches

Made from borosilicate glass with two bulbs, overall height 125x25mm dia. Approx.

One three way syringe and provision for air motor and air rotor hand piece.

The setup is designed to study the forced developed by a jet of water on different surfaces and to compare it with momentum theory. Set up consists of two side visible test enclosure, supply tank, measuring tank and pump for closed loop water circulation. The visible test section housed one nozzle fitted in vertical upward direction to target the jet of water opposite an interchangeable test surface (either flat plate or a hemispherical cup) which in term is connected to a spring loaded stem. The lift of stem and weight added to the pan on other side gives the calculation of corresponding force. The flow rate of water is measured using measuring tank and stop watch provided

The apparatus consists of a plain steel shaft excavated in a bearing and directly driven by a fhp motor. The bearing is freely supported on the shaft and sealed at the motor end. The speed of the motor is controlled accurately by the speed control unit and it can be made run in both directions. Twelve equal-spaced pressure taping around the circumference and four along the axis are provided and are connected to manometer by pu tubing so that the pressure head of oil in all tubes can be observed at a time. The bearing can be loaded by attaching weights to the arm supported beneath it.

Available in 3 Models - 5ul-40, 40ul-200, 200ul-1000ul
Ergonomic Design, light weight construction reduces strain on your hand.
Piston action smooth and controllable.
Two step operation reduces use of reverse pipetting from same tip, ensures last drop dispersing.

EDUCATIONAL ROTATING WORLD GLOBE: Available in Laminated and Varnished finish. Colours: Blue /Black /Yellow wood

Animal cell on stand showing very correctly details of all the structures. Dissectable in seven parts on stand

With triple revolving nose-piece, iris diaphragm and fixed condenser, complete with Indian optics, two objectives 10x, 45x or 40x and two eye-pieces 10x, 15x in ply wood case with lock and key.

AIDS VIRUS HIV virus model is enlarged millions of times, shows the outer lipid membrane with protein structures and the internal nucleus which contains the viral hereditary matter [RNA]. The nucleus is removable and condoms can be put underneath to provide a message regarding measures to be taken for protecting against HIV infections.Supplied without condoms, on stand,with key card.

IC engines are widely used in automobile, domestic and industrial sector. They are classified according to cycle, number of cylinders, arrangement of cylinders, fuel used, type of ignition, valve arrangement, cooling system. Test rigs are used to find out the performance of an IC engine. It consists of an IC Engine, dynamometer, fuel measuring, air intake measuring and various other arrangements. Provision for mores test is done.

The apparatus consists of a Nozzle meter. The flow can be regulated by the valve provided at the down stream Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch

In plastic container, mass type rating at slow discharge. With terminals. PHY-1001.1 2 volt 20 Amphr PHY-1001.2 2 volt 40 Amphr

It consists of two concentric chambers, the inner chamber and the outer chamber, which communicates with each other through an opening at the top. As the steam discharges through the metal basket, which has a large number of holes, the water particles due to their heavier momentum get separated from the steam and collect in the chamber. The comparatively dry steam in the inner chamber moves up and than down aging through the annular space between the two chambers and enters the Throttling Calorimeter.

Gear train is any combination of gear wheels by which motion is transmitted from one shaft to another shaft. In epicyclic gear trains, the axes of shafts on which the gears are mounted may move relative to a fixed axis.
it is a motorized unit consisting of a sun gear mounted on input shaft. Two plane gear meshes with the annular gear. These planet gears are mounted on a common arm to which output shaft is fitted. Loading arrangement is provided for loading the system and to measure holding torque.

The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter and other contain an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter & Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stopwatch.