I. Rating
• 2 KVA to 25 KVA (I/P)
• 6 KVA to 2000 KVA (III/P)

II. InputRange
• 140V-280V (Single Phase)
• 160V-280V (Single Phase)
• 180V-280V (Single Phase)
• 240V-485V (Three Phase)
• 270V-485V (Three Phase)
• 300V-485V (Three Phase)

III. OutputRange
• 230V (Single Phase)
• 400V (Three Phase)

IV. Accuracy
• ± 1% (I/III Phase)

V. Frequency
• 47Hz-53Hz (Single Phase)
• 47Hz-53Hz (Three Phase)

VI. Power Factor Effect
• None

VII. Wave Form Distortion
• None added

VIII. Control
• Digital

IX. Response Time
• Less Than 10 ms.

X. Correction Rate
• 15V-40V/Sec.

XI. Display
• Digital / Analogue

XII. Log book
• Memory(Non-volatile)
• No. of Hrs. of operation on mains
• Peak Current demand
• Nos. of Abnormal High Voltage cut-off events.
• Nos. of Abnormal Low Voltage cut-off events.
• No.of Hrs.of operation on DG

XIII.Programmable Features(Through two parallel way reset table passwords)
• HV cut-off set
• LV cut-off set
• O/L trip set
• Time delay set
• Operating mode (auto / manual)

XIV. Cooling
• Air / Oil Cooled

XV.Protection
• Automatic Switch-Off against:
• Under / Over-Voltage
• Over-Load/Short - Circuit
• Single Phasing
• Surge Protection
• Lightning Protection

XVI. Efficiency
• 97%

The Air Cooled Stabilizers manufactured by us are automatic line voltage corrector which uses synchronous motor in close loop control. These also have provision for manual correction of voltage which is introduced on client's requirement.

Rating:

Single phase unit: 1 KVA– 25 KVA
Three phase unit: 6 KVA– 200 KVA

Nominal Output Voltage:

Single phase unit: 230 V
Three phase unit: 400 V

Voltage Correction Rate:

Air Cooled: 10-25 V/ Sec in Single Phase and 15-40 V/ Sec in Three Phase

Efficiency:

97% in both the cases

Our Isolation Transformers isolates the equipments from noisy power line hence providing a better option to clients. These remove power line noise, surges, spikes and transients.

Other Features :

• High insulation resistance
• Provide complete electromagnetic and electrostatic shielding

Applications:

They have got use in Analytical Instruments, CNC Machines, Computers & Peripherals, Communication Equipments, Medical Instruments etc.

Other Specifications:

Input voltage: 220 V
Output voltage: 220 V
Frequency: 50 hz
Construction: As per ISO- 2026
Lamination: Cargo
Losses: 5%

Phase & Neutral Balance System: Phase & Neutral Balance System: Phase & Neutral Balancing System is a three-phase system, which is installed at the low voltage supply line between phases and neutral i.e., parallel to the impedances. PNBS due to its magnetic symmetry tries to establish neutral point symmetrical with respect to the phase voltages. Thus, it equalizes the voltages in all the three phases and minimizes the neutral current.

Insurance Against Neutral Break: Due to any break in neutral connection, a consumer gets 415 Volts instead of 230 Volts. This damages most of the Electrical, Electronic, Telecom equipments and Household appliances. PNBS continues to provide neutral, protecting valuable equipment / appliances against any such damages.

Capacity of PNBS:

Capacity of PNBS In a balanced Three Phase system the current flowing through the neutral should be zero. However, it is practically not possible to distribute & ensure equal loading of each phase. Uneven loading on the phases, causes unbalanced phase voltage, phase distortion and excessive current flowing through the neutral, which results in loss of energy. PNBS corrects this situation. In a balanced Three Phase system the current flowing through the neutral should be zero. However, it is practically not possible to distribute & ensure equal loading of each phase. Uneven loading on the phases, causes unbalanced phase voltage, phase distortion and excessive current flowing through the neutral, which results in loss of energy. PNBS corrects this situation.
The PNBS equalizes the phase voltage, maintains phase angle symmetry and minimizes the neutral current. The capacity of PNBS is therefore defined in terms of its ability to correct the error measured in terms of the neutral current. The capacity of the PNBS required is dependent on the situation, at a particular location.

Specifications of Battery Protector

1. Operating Voltage: 24-72 V DC

2. Cut-off Voltage: @ 1.75 V per cell

3. Pre alarm before disconnection of battery: Audio Provided

4.DC Contactor used: Prestolite UK make SPST Connector

5. Measurement of battery voltage & current: Through 72 x 72 mm Digital DC V/A. Meter for charging current and discharging current.

6.Display of the meter: 3½ digital display

7. Re-connection: Batteries get automatically connected to the power plant as
soon as mains are resumed.

8.Suitable for rural as well as urban telecom areas.

Specification Of Automatic Voltage Stabilizer:

1. Input range from 160- 280, 140- 280, 110- 275 & 90- 280 Volts
2. Output Voltage 200- 240
3. Load capacity range from 1 KVA to 10 KVA in single phase & 3 KVA to 30 KVA in three phase.
4. Completely copper bound Buck / Boost Transformer
5. Special grade silicon steel lamination (core) for transformer
6. Completely solid-state control card.
7. Electromagnetic realy for reliable performance
8. Digital / Analogue volt/ Amp. Meter

Optional Features:

1. Under / Over Voltage % time delay protection
2. Over current protection
3. By-pass & Single Phase Preventer

We offer high quality Step Down Transformers. These are offered with the following features:

• 100 Watt maximum capacity heavy-duty continuous use transformer
• One grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs)
• Hard wired
• Durable design with a heavy-duty cord

We offer high quality Voltage Transformers. These are offered with the following features:

• Panel mount, single phase (fixed and adjustable shaft)
• Enclosed cord and plug
• Metered
• Fully enclosed
• Ganged